mirror of
https://github.com/projectacrn/acrn-hypervisor.git
synced 2025-06-21 21:19:35 +00:00
doc: update partition mode config on up2
Update the using_partition_mode_on_up2.rst to accormodate the latest configuration method for up2 partition mode. Signed-off-by: Victor Sun <victor.sun@intel.com>
This commit is contained in:
Victor Sun
David Kinder
parent
02ae775bfa
commit
4928be5f8b
@ -93,7 +93,7 @@ Enable partition mode in ACRN hypervisor
|
|||||||
****************************************
|
****************************************
|
||||||
|
|
||||||
#. Before building the ACRN hypervisor, you need to figure out the I/O address
|
#. Before building the ACRN hypervisor, you need to figure out the I/O address
|
||||||
of the serial port, and the PCI BAR addresses of the SATA controller and
|
of the serial port, and the PCI BDF addresses of the SATA controller and
|
||||||
the USB controller on your UP2 board.
|
the USB controller on your UP2 board.
|
||||||
|
|
||||||
Enter the following command to get the I/O addresses of the serial ports.
|
Enter the following command to get the I/O addresses of the serial ports.
|
||||||
@ -113,12 +113,10 @@ Enable partition mode in ACRN hypervisor
|
|||||||
The second with ``00:18.1`` is the one on the 40-pin expansion connector.
|
The second with ``00:18.1`` is the one on the 40-pin expansion connector.
|
||||||
|
|
||||||
The following command prints detailed information about all PCI buses
|
The following command prints detailed information about all PCI buses
|
||||||
and devices in the system. Look up the PCI BAR addresses of the SATA
|
and devices in the system.
|
||||||
controller and the USB controller, record these addresses (highlighted below) for
|
|
||||||
editing the source code later.
|
|
||||||
|
|
||||||
.. code-block:: none
|
.. code-block:: none
|
||||||
:emphasize-lines: 1,9,10,14,22
|
:emphasize-lines: 1,3,16
|
||||||
|
|
||||||
$ sudo lspci -vv
|
$ sudo lspci -vv
|
||||||
...
|
...
|
||||||
@ -164,136 +162,142 @@ Enable partition mode in ACRN hypervisor
|
|||||||
Refer to the :ref:`getting-started-building` for more information on how
|
Refer to the :ref:`getting-started-building` for more information on how
|
||||||
to install all the ACRN build dependencies.
|
to install all the ACRN build dependencies.
|
||||||
|
|
||||||
|
#. Prepare VM configurations for UP2 partition mode
|
||||||
|
|
||||||
|
The BOARD specific VM configurations should be under the folder:
|
||||||
|
``hypervisor/arch/x86/configs/$(CONFIG_BOARD)/``.
|
||||||
|
|
||||||
|
For UP2 board, we can simply copy configurations of apl-mrb to the up2 folder:
|
||||||
|
|
||||||
|
.. code-block:: none
|
||||||
|
|
||||||
|
$ cp hypervisor/arch/x86/configs/apl-mrb/* hypervisor/arch/x86/configs/up2/
|
||||||
|
|
||||||
|
#. Configure the partition mode configuration arguments
|
||||||
|
|
||||||
|
The partition mode configuration information is located in header file
|
||||||
|
``hypervisor/arch/x86/configs/up2/partition_config.h`` and configured by
|
||||||
|
``VMx_CONFIG_XXXX`` MACROs (where x is the VM id number and XXXX are arguments).
|
||||||
|
The most frequent configure items for end user are:
|
||||||
|
|
||||||
|
``VMx_CONFIG_NAME``: the VMx name string, must less than 32 bytes;
|
||||||
|
|
||||||
|
``VMx_CONFIG_PCPU_BITMAP``: assign physical CPUs to VMx by MACRO of ``PLUG_CPU(cpu_id)``;
|
||||||
|
|
||||||
|
Below is an example of partition mode configuration for UP2:
|
||||||
|
|
||||||
|
.. code-block:: none
|
||||||
|
:caption: hypervisor/arch/x86/configs/up2/partition_config.h
|
||||||
|
|
||||||
|
...
|
||||||
|
#define VM0_CONFIGURED
|
||||||
|
|
||||||
|
#define VM0_CONFIG_NAME "PRE-LAUNCHED VM1 for UP2"
|
||||||
|
#define VM0_CONFIG_TYPE PRE_LAUNCHED_VM
|
||||||
|
#define VM0_CONFIG_PCPU_BITMAP (PLUG_CPU(0) | PLUG_CPU(2))
|
||||||
|
#define VM0_CONFIG_FLAGS IO_COMPLETION_POLLING
|
||||||
|
#define VM0_CONFIG_MEM_START_HPA 0x100000000UL
|
||||||
|
#define VM0_CONFIG_MEM_SIZE 0x20000000UL
|
||||||
|
|
||||||
|
#define VM0_CONFIG_OS_NAME "ClearLinux 26600"
|
||||||
|
#define VM0_CONFIG_OS_BOOTARGS "root=/dev/sda3 rw rootwait noxsave maxcpus=2 nohpet console=hvc0 \
|
||||||
|
console=ttyS2 no_timer_check ignore_loglevel log_buf_len=16M \
|
||||||
|
consoleblank=0 tsc=reliable xapic_phys"
|
||||||
|
|
||||||
|
#define VM1_CONFIGURED
|
||||||
|
|
||||||
|
#define VM1_CONFIG_NAME "PRE-LAUNCHED VM2 for UP2"
|
||||||
|
#define VM1_CONFIG_TYPE PRE_LAUNCHED_VM
|
||||||
|
#define VM1_CONFIG_PCPU_BITMAP (PLUG_CPU(1) | PLUG_CPU(3))
|
||||||
|
#define VM1_CONFIG_FLAGS IO_COMPLETION_POLLING
|
||||||
|
#define VM1_CONFIG_MEM_START_HPA 0x120000000UL
|
||||||
|
#define VM1_CONFIG_MEM_SIZE 0x20000000UL
|
||||||
|
|
||||||
|
#define VM1_CONFIG_OS_NAME "ClearLinux 26600"
|
||||||
|
#define VM1_CONFIG_OS_BOOTARGS "root=/dev/sda3 rw rootwait noxsave maxcpus=2 nohpet console=hvc0 \
|
||||||
|
console=ttyS2 no_timer_check ignore_loglevel log_buf_len=16M \
|
||||||
|
consoleblank=0 tsc=reliable xapic_phys"
|
||||||
|
|
||||||
|
#define VM0_CONFIG_PCI_PTDEV_NUM 2U
|
||||||
|
#define VM1_CONFIG_PCI_PTDEV_NUM 3U
|
||||||
|
|
||||||
#. Configure the PCI device info for each VM
|
#. Configure the PCI device info for each VM
|
||||||
|
|
||||||
PCI devices that are available to the privileged VMs
|
PCI devices that are available to the privileged VMs
|
||||||
are hardcoded in the source file ``hypervisor/partition/apl-mrb/vm_description.c``.
|
are hardcoded in the source file ``hypervisor/arch/x86/configs/up2/pt_dev.c``.
|
||||||
You need to review and modify the ``vpci_vdev_array1`` and ``vpci_vdev_array2``
|
You need to review and modify the ``vm0_pci_ptdevs`` and ``vm1_pci_ptdevs``
|
||||||
structures in the source code to match the PCI BAR addresses of the SATA
|
structures in the source code to match the PCI BDF addresses of the SATA
|
||||||
controller and the USB controller noted in step 1:
|
controller and the USB controller noted in step 1:
|
||||||
|
|
||||||
.. code-block:: none
|
.. code-block:: none
|
||||||
:emphasize-lines: 3,39,44,49,56,72
|
:emphasize-lines: 5,9,17,21,25
|
||||||
:caption: hypervisor/partition/vm_description.c
|
:caption: hypervisor/arch/x86/configs/up2/pt_dev.c
|
||||||
|
|
||||||
...
|
...
|
||||||
static struct vpci_vdev_array vpci_vdev_array1 = {
|
struct acrn_vm_pci_ptdev_config vm0_pci_ptdevs[2] = {
|
||||||
.num_pci_vdev = 2,
|
{
|
||||||
|
.vbdf.bits = {.b = 0x00U, .d = 0x00U, .f = 0x00U},
|
||||||
|
.pbdf.bits = {.b = 0x00U, .d = 0x00U, .f = 0x00U},
|
||||||
|
},
|
||||||
|
{
|
||||||
|
.vbdf.bits = {.b = 0x00U, .d = 0x01U, .f = 0x00U},
|
||||||
|
.pbdf.bits = {.b = 0x00U, .d = 0x12U, .f = 0x00U},
|
||||||
|
},
|
||||||
|
};
|
||||||
|
|
||||||
.vpci_vdev_list = {
|
|
||||||
{/*vdev 0: hostbridge */
|
|
||||||
.vbdf.bits = {.b = 0x00U, .d = 0x00U, .f = 0x0U},
|
|
||||||
.ops = &pci_ops_vdev_hostbridge,
|
|
||||||
.bar = {},
|
|
||||||
.pdev = {
|
|
||||||
.bdf.bits = {.b = 0x00U, .d = 0x00U, .f = 0x0U},
|
|
||||||
}
|
|
||||||
},
|
|
||||||
|
|
||||||
{/*vdev 1: SATA controller*/
|
|
||||||
.vbdf.bits = {.b = 0x00U, .d = 0x01U, .f = 0x0U},
|
|
||||||
.ops = &pci_ops_vdev_pt,
|
|
||||||
.bar = {
|
|
||||||
[0] = {
|
|
||||||
.base = 0UL,
|
|
||||||
.size = 0x2000UL,
|
|
||||||
.type = PCIBAR_MEM32
|
|
||||||
},
|
|
||||||
[1] = {
|
|
||||||
.base = 0UL,
|
|
||||||
.size = 0x1000UL,
|
|
||||||
.type = PCIBAR_MEM32
|
|
||||||
},
|
|
||||||
[5] = {
|
|
||||||
.base = 0UL,
|
|
||||||
.size = 0x1000UL,
|
|
||||||
.type = PCIBAR_MEM32
|
|
||||||
},
|
|
||||||
},
|
|
||||||
.pdev = {
|
|
||||||
.bdf.bits = {.b = 0x00U, .d = 0x12U, .f = 0x0U},
|
|
||||||
.bar = {
|
|
||||||
[0] = {
|
|
||||||
.base = 0x91514000UL,
|
|
||||||
.size = 0x2000UL,
|
|
||||||
.type = PCIBAR_MEM32
|
|
||||||
},
|
|
||||||
[1] = {
|
|
||||||
.base = 0x91537000UL,
|
|
||||||
.size = 0x100UL,
|
|
||||||
.type = PCIBAR_MEM32
|
|
||||||
},
|
|
||||||
[5] = {
|
|
||||||
.base = 0x91536000UL,
|
|
||||||
.size = 0x800UL,
|
|
||||||
.type = PCIBAR_MEM32
|
|
||||||
},
|
|
||||||
}
|
|
||||||
...
|
...
|
||||||
static struct vpci_vdev_array vpci_vdev_array2 = {
|
struct acrn_vm_pci_ptdev_config vm1_pci_ptdevs[3] = {
|
||||||
.num_pci_vdev = 3,
|
{
|
||||||
...
|
.vbdf.bits = {.b = 0x00U, .d = 0x00U, .f = 0x00U},
|
||||||
{/*vdev 1: USB controller*/
|
.pbdf.bits = {.b = 0x00U, .d = 0x00U, .f = 0x00U},
|
||||||
.vbdf.bits = {.b = 0x00U, .d = 0x01U, .f = 0x0U},
|
|
||||||
.ops = &pci_ops_vdev_pt,
|
|
||||||
.bar = {
|
|
||||||
[0] = {
|
|
||||||
.base = 0UL,
|
|
||||||
.size = 0x10000UL,
|
|
||||||
.type = PCIBAR_MEM32
|
|
||||||
},
|
},
|
||||||
|
{
|
||||||
|
.vbdf.bits = {.b = 0x00U, .d = 0x01U, .f = 0x00U},
|
||||||
|
.pbdf.bits = {.b = 0x00U, .d = 0x15U, .f = 0x00U},
|
||||||
},
|
},
|
||||||
.pdev = {
|
{
|
||||||
.bdf.bits = {.b = 0x00U, .d = 0x15U, .f = 0x0U},
|
.vbdf.bits = {.b = 0x00U, .d = 0x02U, .f = 0x00U},
|
||||||
.bar = {
|
.pbdf.bits = {.b = 0x02U, .d = 0x00U, .f = 0x00U},
|
||||||
[0] = {
|
|
||||||
.base = 0x91500000UL,
|
|
||||||
.size = 0x10000UL,
|
|
||||||
.type = PCIBAR_MEM64
|
|
||||||
},
|
},
|
||||||
}
|
};
|
||||||
...
|
...
|
||||||
|
|
||||||
#. Optionally, configure the ``.bootargs`` kernel command line arguments
|
.. note::
|
||||||
|
|
||||||
|
The first BDF(0:0.0) is for host bridge;
|
||||||
|
``vbdf.bits`` in each VM could be any BDF if it is valid and no confliction.
|
||||||
|
|
||||||
|
#. Optionally, configure the ``VMx_CONFIG_OS_BOOTARGS`` kernel command line arguments
|
||||||
|
|
||||||
The kernel command line arguments used to boot the privileged VMs are
|
The kernel command line arguments used to boot the privileged VMs are
|
||||||
hardcoded as ``/dev/sda3`` to meet the Clear Linux OS automatic installation.
|
hardcoded as ``/dev/sda3`` to meet the Clear Linux OS automatic installation.
|
||||||
In case you plan to use your customized root
|
In case you plan to use your customized root
|
||||||
filesystem, you may optionally edit the ``root=`` parameter specified
|
filesystem, you may optionally edit the ``root=`` parameter specified
|
||||||
in the ``.bootargs`` field of the ``.vm_desc_array`` structure, to
|
in the ``VMx_CONFIG_OS_BOOTARGS`` MACRO, to instruct the Linux kernel to
|
||||||
instruct the Linux kernel to mount the right disk partition:
|
mount the right disk partition:
|
||||||
|
|
||||||
.. code-block:: none
|
.. code-block:: none
|
||||||
:emphasize-lines: 9-11,20-22
|
:emphasize-lines: 12-14
|
||||||
:caption: hypervisor/partition/vm_description.c
|
:caption: hypervisor/arch/x86/configs/up2/partition_config.h
|
||||||
|
|
||||||
...
|
...
|
||||||
/* Virtual Machine descriptions */
|
#define VM0_CONFIGURED
|
||||||
.vm_desc_array = {
|
|
||||||
{
|
#define VM0_CONFIG_NAME "PRE-LAUNCHED VM1 for UP2"
|
||||||
/* Internal variable, MUSTBE init to -1 */
|
#define VM0_CONFIG_TYPE PRE_LAUNCHED_VM
|
||||||
.vm_hw_num_cores = VM1_NUM_CPUS,
|
#define VM0_CONFIG_PCPU_BITMAP (PLUG_CPU(0) | PLUG_CPU(2))
|
||||||
.vm_pcpu_ids = &VM1_CPUS[0],
|
#define VM0_CONFIG_FLAGS IO_COMPLETION_POLLING
|
||||||
...
|
#define VM0_CONFIG_MEM_START_HPA 0x100000000UL
|
||||||
.bootargs = "root=/dev/sda3 rw rootwait noxsave maxcpus=2 nohpet console=hvc0 \
|
#define VM0_CONFIG_MEM_SIZE 0x20000000UL
|
||||||
|
|
||||||
|
#define VM0_CONFIG_OS_NAME "ClearLinux 26600"
|
||||||
|
#define VM0_CONFIG_OS_BOOTARGS "root=/dev/sda3 rw rootwait noxsave maxcpus=2 nohpet console=hvc0 \
|
||||||
console=ttyS2 no_timer_check ignore_loglevel log_buf_len=16M \
|
console=ttyS2 no_timer_check ignore_loglevel log_buf_len=16M \
|
||||||
consoleblank=0 tsc=reliable xapic_phys",
|
consoleblank=0 tsc=reliable xapic_phys"
|
||||||
.vpci_vdev_array = &vpci_vdev_array1,
|
|
||||||
.mptable = &mptable_vm1,
|
.. note::
|
||||||
},
|
|
||||||
{
|
The root device for VM1 is also /dev/sda3 since the USB controller is the only one seen in that VM.
|
||||||
/* Internal variable, MUSTBE init to -1 */
|
|
||||||
.vm_hw_num_cores = VM2_NUM_CPUS,
|
|
||||||
.vm_pcpu_ids = &VM2_CPUS[0],
|
|
||||||
...
|
|
||||||
.bootargs = "root=/dev/sda3 rw rootwait noxsave maxcpus=2 nohpet console=hvc0 \
|
|
||||||
console=ttyS2 no_timer_check ignore_loglevel log_buf_len=16M \
|
|
||||||
consoleblank=0 tsc=reliable xapic_phys",
|
|
||||||
.vpci_vdev_array = &vpci_vdev_array2,
|
|
||||||
.mptable = &mptable_vm2,
|
|
||||||
.lapic_pt = true,
|
|
||||||
},
|
|
||||||
}
|
|
||||||
|
|
||||||
#. Build the ACRN hypervisor and copy the artifact ``acrn.32.out`` to the
|
#. Build the ACRN hypervisor and copy the artifact ``acrn.32.out`` to the
|
||||||
``/boot`` directory:
|
``/boot`` directory:
|
||||||
@ -362,18 +366,18 @@ and press :kbd:`CTRL+Space` keys to return to the ACRN serial console.
|
|||||||
|
|
||||||
ACRN Hypervisor
|
ACRN Hypervisor
|
||||||
calibrate_tsc, tsc_khz=1094400
|
calibrate_tsc, tsc_khz=1094400
|
||||||
[21017289us][cpu=0][sev=2][seq=1]:HV version 0.3-unstable-2018-11-08 12:41:24-ef974d1a-dirty DBG (daily tag:acrn-2018w45.3-140000p) build by clear, start time 20997424us
|
[21017289us][cpu=0][sev=2][seq=1]:HV version 0.6-unstable-2019-02-02 22:30:31-d0c2a88-dirty DBG (daily tag:acrn-2019w05.4-140000p) build by clear, start time 20997424us
|
||||||
[21034127us][cpu=0][sev=2][seq=2]:API version 1.0
|
[21034127us][cpu=0][sev=2][seq=2]:API version 1.0
|
||||||
[21039218us][cpu=0][sev=2][seq=3]:Detect processor: Intel(R) Pentium(R) CPU N4200 @ 1.10GHz
|
[21039218us][cpu=0][sev=2][seq=3]:Detect processor: Intel(R) Pentium(R) CPU N4200 @ 1.10GHz
|
||||||
[21048422us][cpu=0][sev=2][seq=4]:hardware support HV
|
[21048422us][cpu=0][sev=2][seq=4]:hardware support HV
|
||||||
[21053897us][cpu=0][sev=1][seq=5]:SECURITY WARNING!!!!!!
|
[21053897us][cpu=0][sev=1][seq=5]:SECURITY WARNING!!!!!!
|
||||||
[21059672us][cpu=0][sev=1][seq=6]:Please apply the latest CPU uCode patch!
|
[21059672us][cpu=0][sev=1][seq=6]:Please apply the latest CPU uCode patch!
|
||||||
[21074487us][cpu=0][sev=2][seq=28]:Start VM1
|
[21074487us][cpu=0][sev=2][seq=28]:Start VM id: 1 name: PRE-LAUNCHED VM2 for UP2
|
||||||
[21074488us][cpu=3][sev=2][seq=29]:Start VM2
|
[21074488us][cpu=3][sev=2][seq=29]:Start VM id: 0 name: PRE-LAUNCHED VM1 for UP2
|
||||||
[21885195us][cpu=0][sev=3][seq=34]:vlapic: Start Secondary VCPU1 for VM[1]...
|
[21885195us][cpu=0][sev=3][seq=34]:vlapic: Start Secondary VCPU1 for VM[1]...
|
||||||
[21889889us][cpu=3][sev=3][seq=35]:vlapic: Start Secondary VCPU1 for VM[2]...
|
[21889889us][cpu=3][sev=3][seq=35]:vlapic: Start Secondary VCPU1 for VM[2]...
|
||||||
ACRN:\>
|
ACRN:\>
|
||||||
ACRN:\>sos_console 1
|
ACRN:\>sos_console 0
|
||||||
|
|
||||||
----- Entering Guest 1 Shell -----
|
----- Entering Guest 1 Shell -----
|
||||||
[ 1.997439] systemd[1]: Listening on Network Service Netlink Socket.
|
[ 1.997439] systemd[1]: Listening on Network Service Netlink Socket.
|
||||||
@ -390,7 +394,7 @@ and press :kbd:`CTRL+Space` keys to return to the ACRN serial console.
|
|||||||
root@clr-932c8a3012ec4dc6af53790b7afbf6ba ~ #
|
root@clr-932c8a3012ec4dc6af53790b7afbf6ba ~ #
|
||||||
|
|
||||||
---Entering ACRN SHELL---
|
---Entering ACRN SHELL---
|
||||||
ACRN:\>sos_console 2
|
ACRN:\>sos_console 1
|
||||||
|
|
||||||
----- Entering Guest 2 Shell -----
|
----- Entering Guest 2 Shell -----
|
||||||
[ 1.490122] usb 1-4: new full-speed USB device number 2 using xhci_hcd
|
[ 1.490122] usb 1-4: new full-speed USB device number 2 using xhci_hcd
|
||||||
|
|||||||
Loading…
Reference in New Issue
Block a user