- add new struct member for acrn_vm_config;
- add sharing_config.c file with initialized vm_config array;
- add SOS VM config header for apl-mrb/apl-nuc/up2 and dnv-cb2 board;
- and partition_config.c file with dummy vm_config array;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This will be consistent with naming of apl-mrb/kbl-nuc ...
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
SBL doesn't support 40-pin header for now, so the serial PCI
device(0:18:1) on it doesn't work. Let's just workaround this by
changing hv's default serial output device to 0:18:0. In the future,
we'd rather change it back if SBL supports it.
This change is only for SBL, for UEFI, now we offer serial configuration
through command line parameter(vuart=...).
Tracked-On: #1995
Signed-off-by: Tw <wei.tan@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
before PCI_BDF uses its hex value like "0xC2" for "0:18.2" to
configure, now use "0:18.2" directly to make it more readable
and easier to configure.
Tracked-On: #2031
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
now UP2 board use ttyS1 as debug uart in HV, and vuart ttyS0 in
SOS kernel (acrn.conf default configure), its default IRQ is 4,
but SOS kernel will also assign IRQ4 to its ttyS1, they're sharing
one IRQ, and it can cause SOS boot hung issue, for HV not support
sharing IRQ now.
some boards use ttyS0 as debug uart, it has not this issue; for that
board, SOS will assign IRQ5 to its ttyS1, no sharing IRQ.
change it to IRQ6 to avoid the issue.
Tracked-On: #2030
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Combination of BOARD and FIRMWARE is a more precious definition.
And we decide PLATFORM_XXX based on FIRMWARE, remove relative one in
board config.
We reserve PLATFORM for backward compatibility.
Tracked-On: #1995
Signed-off-by: Tw <wei.tan@intel.com>
Reviewed-by: Yin Fengwei < fengwei.yin@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
replace serial PCI MMIO base address configure with its BDF configure.
Tracked-On: #1923
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch allows to disable the serial port directly from Kconfig. This used
to only be possible from the command-line (by passing "uart=disabled"). To
disable the serial port via Kconfig, simply unselect the "Serial IO type"
option.
The default options do not seem to have any effect anymore (and were confusing
anyway) so they are removed and the serial port is enabled for various platforms
in their corresponding *.config file.
Tracked-On: #1481
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
The current defconfigs are BIOS-specific which makes it difficult to maintain
multiple defconfigs for boards running the same BIOS.
This patch re-organizes the defconfigs to be board-specific. A command line
option BOARD is introduced to specify a board on which the current build targets
at. The original PLATFORM is kept for backward compatibility which redirects to
apl-mrb and nuc6cayh for sbl and uefi, respectively.
The getting started guide is also updated accordingly.
v1 -> v2:
* Rewrite 'up2' to 'UP2'.
Tracked-On: #1588
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Reviewed-by: Anthony Xu <anthony.xu@intel.com>
This patch converts the configuration entries (previously defined in
bsp/*/include/bsp/bsp_cfg.h) to a Kconfig script.
With the platform specified, the default values will be exactly those in the
corresponding bsp_cfg.h.
v4 -> v5:
* No changes.
v3 -> v4:
* No changes.
v2 -> v3:
* No changes.
v1 -> v2:
* No changes.
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
