#!/bin/sh
# SPDX-License-Identifier: Apache-2.0
#
# Copyright (C) 2023 The Falco Authors.
#
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#

# By default, we use the automatic selection for drivers
chosen_driver="auto"
chosen_unit=
CHOICE=

# Every time we call this script we want to stat from a clean state.
echo "[POST-INSTALL] Disable all possible 'falco' services:"
systemctl --system stop 'falco-kmod.service' || true
systemctl --system stop 'falco-bpf.service' || true
systemctl --system stop 'falco-modern-bpf.service' || true
systemctl --system stop 'falco-custom.service' || true
systemctl --system stop 'falcoctl-artifact-follow.service' || true
systemctl --system disable 'falco-kmod.service' || true
systemctl --system disable 'falco-bpf.service' || true
systemctl --system disable 'falco-modern-bpf.service' || true
systemctl --system disable 'falco-custom.service' || true
systemctl --system disable 'falcoctl-artifact-follow.service' || true

# unmask falcoctl if it was masked
systemctl --system unmask falcoctl-artifact-follow.service || true

if [ "$1" = "configure" ]; then
	# "auto" case is not managed here since it is already the default, so no CHOICE=2
        case $FALCO_DRIVER_CHOICE in
              none)
                  CHOICE=1
                  ;;
              kmod)
                  CHOICE=3
                  ;;
              ebpf)
                  CHOICE=4
                  ;;
              modern_ebpf)
                  CHOICE=5
                  ;;
        esac     
        if [ -z $CHOICE ] && [ -x /usr/bin/dialog ] && [ "${FALCO_FRONTEND}" != "noninteractive" ]; then          
            # If dialog is installed, create a dialog to let users choose the correct driver for them
            CHOICE=$(dialog --clear --title "Falco drivers" --menu "Choose your preferred driver:" 12 55 4 \
                    1 "Manual configuration (no unit is started)" \
                    2 "Automatic selection" \
                    3 "Kmod" \
                    4 "eBPF" \
                    5 "Modern eBPF" \
                    2>&1 >/dev/tty)
        fi
        # "auto" case is not managed here since it is already the default, so no CHOICE=2
        case $CHOICE in
            1)
                chosen_driver=""
                ;;
            3)
                chosen_driver="kmod"
                ;;
            4)
                chosen_driver="ebpf"
                ;;
            5)
                chosen_driver="modern_ebpf"
                ;;
        esac
        if [ -n "$chosen_driver" ]; then
            echo "[POST-INSTALL] Configure falcoctl '$chosen_driver' driver type:"
            if [ "$chosen_driver" = "auto" ];  then
                # Configure falcoctl to enable all drivers
                falcoctl driver config --type "modern_ebpf" --type "kmod" --type "ebpf"
                # Load the actually automatic chosen driver
                chosen_driver=$(falcoctl driver printenv | grep DRIVER= | cut -d'"' -f2)
            else
                falcoctl driver config --type "$chosen_driver"
            fi
            CHOICE=
            case $FALCOCTL_ENABLED in
                no)
                    CHOICE=2
                    ;;
            esac
            if [ -z $CHOICE ] &&  [ -x /usr/bin/dialog ] && [ "${FALCO_FRONTEND}" != "noninteractive" ]; then
                CHOICE=$(dialog --clear --title "Falcoctl" --menu "Do you want to follow automatic ruleset updates?" 10 40 2 \
                        1 "Yes" \
                        2 "No" \
                        2>&1 >/dev/tty)
            fi  
            case $CHOICE in
                2)
                    # we don't want falcoctl enabled, we mask it
                    systemctl --system mask falcoctl-artifact-follow.service || true
                ;;
            esac
        fi    
        clear
fi

set -e

echo "[POST-INSTALL] Trigger deamon-reload:"
systemctl --system daemon-reload || true

# If needed, try to load/compile the driver through falcoctl
case "$chosen_driver" in
    "kmod")
      # Only compile for kmod, in this way we use dkms
      echo "[POST-INSTALL] Call 'falcoctl driver install for kmod:"
      falcoctl driver install --download=false
      chosen_unit="kmod"
      ;;
    "ebpf")
      echo "[POST-INSTALL] Call 'falcoctl driver install for ebpf':"
      falcoctl driver install
      chosen_unit="bpf"
      ;;
    "modern_ebpf")
      chosen_unit="modern-bpf"
      ;;
esac

if [ "$1" = "configure" ] || [ "$1" = "abort-upgrade" ] || [ "$1" = "abort-deconfigure" ] || [ "$1" = "abort-remove" ] ; then
        if [ -n "$chosen_unit" ]; then
            # we do this in 2 steps because `enable --now` is not always supported
            echo "[POST-INSTALL] Enable 'falco-$chosen_unit.service':"
            systemctl --system enable "falco-$chosen_unit.service" || true
            echo "[POST-INSTALL] Start 'falco-$chosen_unit.service':"
            systemctl --system start "falco-$chosen_unit.service" || true
        fi
fi