The recently introduced failure handling in ExpectNoError depends on error
wrapping: if an error prefix gets added with `fmt.Errorf("foo: %v", err)`, then
ExpectNoError cannot detect that the root cause is an assertion failure and
then will add another useless "unexpected error" prefix and will not dump the
additional failure information (currently the backtrace inside the E2E
framework).
Instead of manually deciding on a case-by-case basis where %w is needed, all
error wrapping was updated automatically with
sed -i "s/fmt.Errorf\(.*\): '*\(%s\|%v\)'*\",\(.* err)\)/fmt.Errorf\1: %w\",\3/" $(git grep -l 'fmt.Errorf' test/e2e*)
This may be unnecessary in some cases, but it's not wrong.
The recently introduced failure handling in ExpectNoError depends on error
wrapping: if an error prefix gets added with `fmt.Errorf("foo: %v", err)`, then
ExpectNoError cannot detect that the root cause is an assertion failure and
then will add another useless "unexpected error" prefix and will not dump the
additional failure information (currently the backtrace inside the E2E
framework).
Instead of manually deciding on a case-by-case basis where %w is needed, all
error wrapping was updated automatically with
sed -i "s/fmt.Errorf\(.*\): '*\(%s\|%v\)'*\",\(.* err)\)/fmt.Errorf\1: %w\",\3/" $(git grep -l 'fmt.Errorf' test/e2e*)
This may be unnecessary in some cases, but it's not wrong.
All code must use the context from Ginkgo when doing API calls or polling for a
change, otherwise the code would not return immediately when the test gets
aborted.
ginkgo.DeferCleanup has multiple advantages:
- The cleanup operation can get registered if and only if needed.
- No need to return a cleanup function that the caller must invoke.
- Automatically determines whether a context is needed, which will
simplify the introduction of context parameters.
- Ginkgo's timeline shows when it executes the cleanup operation.
The original intention (adding more information for later analysis)
is probably obsolete because there is no code which does anything
with the extended error.
The code in upgrade_suite.go collected it in an in-memory JUnit report, but
then didn't do anything with that field. The code also wouldn't work for
failures detected by Ginkgo itself, like the upcoming timeout handling. If the
upgrade suite needs the information, it probably should get it from Gingko with
a ReportAfterSuite call instead of depending in some fragile interception
mechanism.
- update all the import statements
- run hack/pin-dependency.sh to change pinned dependency versions
- run hack/update-vendor.sh to update go.mod files and the vendor directory
- update the method signatures for custom reporters
Signed-off-by: Dave Chen <dave.chen@arm.com>
On IPv6 clusters, one of the most frequent problems I encounter is
assumptions that one can build a URL with a host and port simply by
using Sprintf, like this:
```go
fmt.Sprintf("http://%s:%d/foo", host, port)
```
When `host` is an IPv6 address, this produces an invalid URL as it must
be bracketed, like this:
```
http://[2001:4860:4860::8888]:9443
```
This change fixes the occurences of joining a host and port with the
purpose built `net.JoinHostPort` function.
I encounter this problem often enough that I started to [write a linter
for it](https://github.com/stbenjam/go-sprintf-host-port). I don't
think the linter is quite ready for wide use yet, but I did run it
against the Kube codebase and found these. While the host portion in
some of these changes may always be an FQDN or IPv4 IP today, it's an
easy thing that can break later on.
This add e2e test for HPA ContainerResource metrics. This add test to cover two scenarios
1. Scale up on a busy application with an idle sidecar container
2. Do not scale up on a busy sidecar with an idle application.
Signed-off-by: Vivek Singh <svivekkumar@vmware.com>
Extract TestSuite, TestDriver, TestPattern, TestConfig
and VolumeResource, SnapshotVolumeResource from testsuite
package and put them into a new package called api.
The ultimate goal here is to make the testsuites as clean
as possible. And only testsuites in the package.
This drops testfiles.ReadOrDie and updated testfiles.Exists to return an
error, forcing the caller to decide whether to call framework.Fail or do
something else.
It makes for a slightly less friendly API, but also means the package is
decoupled from framework again, as per the comments at the top of the
file
The function is for persistent volumes and it doesn't have any
reason why it stays in core test framework. So this moves the
function into e2epv package for reducing e2e/framework/util.go
code.
There were framework.ExpectNoError(fmt.Errorf(..)) calls which just
raise an exception without actual value checks, they just raised the
specified error messages. These usages of framework.ExpectNoError()
seemed a little tricky, so this replaces them with corresponding check
functions for the readability.
Quite a few images are only used a few times in a few tests. Thus,
the images are being centralized into the agnhost image, reducing
the number of images that have to be pulled and used.
This PR replaces the usage of the following images with agnhost:
- mounttest
- mounttest-user
Additionally, removes the usage of the mounttest-user image and removes
it from kubernetes/test/images. RunAsUser is set instead of having that image.
As of https://github.com/kubernetes/kubernetes/pull/72831, the minimum
docker version is 1.13.1. (and the minimum API version is 1.26). The
only time the `RuntimeAdmitHandler` returns anything other than accept
is when the Docker API version < 1.24. In other words, we can be
confident that Docker will always support sysctl.
As a result, we can delete this unnecessary and docker-specific code.
