P2SB_BAR_ADDR related macros should only be defined in misc_cfg.h only when
p2sb is enabled in scenario xml.
Tracked-On: #5340
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
so that vm_configurations.h/vm_configurations.c are consistent for different boards
The boilerplate code is protected by #ifdef P2SB_BAR_ADDR/#endif, so it will
not hurt if we always produce related code.
Define new macros P2SB_BAR_ADDR_GPA and P2SB_BAR_SIZE to make the code more flexible.
Tracked-On: #5229
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Always use P2SB_ as a prefix for all macro definitions related to P2SB
MMIO passthru. And introduce the new P2SB_VGPIO_DM_ENABLED macro to
indicate the presence of the pre-launched VM which requires the feature.
This macro intends to be used to enclose source files with ifdef where
macros defined by config-tool being used which are available only when
the feature is enabled. It is required to avoid causing compilation
errors when users build HV without enabling the feature.
Tracked-On: #5246
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Two PSE-GPIO controllers of EHL CRB require MSI-X emulation for
pass-thru because it uses multiple MSI vectors. Currently acrn-config
enables MSI-X emulation for only TSN devices. Enable MSI-X emulation
for PSE-GPIOs, too.
Tracked-On: #5242
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
This patch is to expose GPIO chassis interrupts as INTx to safety VM for
EHL. User can configure this per-VM attribute in scenario xml using the
following format:
<pt_intx desc="pt intx mapping.">
(phys_gsi0, virt_gsi0), (phys_gsi1, virt_gsi1), (phys_gsiN, virt_gsiN)
</pt_intx>
The physical and virtual interrupt gsi in each pair are separated by a
comma and enclosed in parentheses. If an integer begins with 0x or 0X,
it is hexadecimal, otherwise, it is assumed to be decimal. Example:
<pt_intx desc="pt intx mapping.">
(1, 0), (0x3, 1), (0x4, 2), (5, 6), (89, 0x12)
</pt_intx>
Tracked-On: #5241
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
This patch is to support direct assignment of P2SB bridge to one pre-launched
VM for EHL. User can configure this per-VM attribute in scenario xml:
<mmio_resources desc="MMIO resources.">
<p2sb>y</p2sb>
</mmio_resources>
Set p2sb to y to passthru P2SB bridge to VM, and n otherwise.
Tracked-On: #5221
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
1.Add macro MAX_CACHE_CLOS_NUM_ENTRIES for CAT, and MAX_MBA_CLOS_NUM_ENTRIES for MBA.
MAX_MBA_CLOS_NUM_ENTRIES:
Max number of Cache Mask entries corresponding to each CLOS.
This can vary if CDP is enabled vs disabled, as each CLOS entry will have corresponding
cache mask values for Data and Code when CDP is enabled.
MAX_CACHE_CLOS_NUM_ENTRIES:
Max number of MBA delay entries corresponding to each CLOS.
2.Move VMx_VCPU_CLOS macro to misc_cfg.h head file.
Tracked-On: #5229
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
HV_SUPPORTED_MAX_CLOS:
This value represents the maximum CLOS that is allowed by ACRN hypervisor.
This value is set to be least common Max CLOS (CPUID.(EAX=0x10,ECX=ResID):EDX[15:0])
among all supported RDT resources in the platform. In other words, it is
min(maximum CLOS of L2, L3 and MBA). This is done in order to have consistent
CLOS allocations between all the RDT resources.
Tracked-On: #5229
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Fix build issue while CDP_ENABLED=y for EHL-CRB-B.
Tracked-On: #5092
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Now the hypervisor configuration source code layout is changed, so acrn-config
need to change accordingly to make sure XML based configuration build success;
Tracked-On: #5077
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
