CAVS audio driver depends on the NHLT table to get topology info.
Enable NHLT table in DM for audio passthrough.
Also increase the size reserved for NHLT in ACPI table from 2048B to 2560B.
Tracked-On: #1284
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
This is temperory workaround for DM crash when doing fastboot
reboot. In fastboot, it will disable USB host functionality by
disable device respsone to one PCI bar. While DM code just release
the bar in this case. Which break the reboot functionality.
The workaround is to remove the assert to avoid DM abort. This is
safe because reboot will remove all memory range registered.
We will have offiical fixing later.
Tracked-On: #1277
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
USB device is connected before UOS is booted up, this scenario is
called 'cold plug' for easy to refer.
Under 'cold plug' situation, the libusb will not report 'connect'
event to device model, hence UOS will not discover 'cold plugged'
device.
This patch add support to fix this issue.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1242
Flat Mode for hub emulation means DM emulates USB devices under hub but
hide hub itself. Under this design the Guest OS cannot see any emulated
hub. So in the perspective of Guest OS, all the emulated devices are
under root hub.
This patch is used to enable feature as mentioned above. And please NOTE,
it is the initial version of hub flat Mode hub emulation, there are one
limitation: only one physical hub is supported. If second physical hub is
connected, the connect and disconnect behavior in second hub may affect
the function of first emulated hub.
The USB HUB device model should be the final long term solution, but it is
very complex. Use flat mode HUB emulation as the short term solution first
to support some USB touch devices which integrated internal HUB.
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Reviewed-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1243
In current code, when read/write msix table, it first handle the case
the offset is in pba range when msix talbe and pba share the same bar.
But the code didn't add the condition whether pba bar equals msix table
bar. It will cause problems for the passthrugh devices,whose pba and msix
table don't share the same bar.
Tracked-On: #1209
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
if some pci devices behind gvt got failures when initlizing at init_pci(), gvt
instance have no chance to be destroied even acrn-dm exits.
NOTE: this patch can not work standalone, a following patch to kernel
side(643d40961cf: "vhm: init client->kthread_exit true") is requied as well,
otherwise it will stucks during destroying gvt instance.
Tracked-On: #1141
Signed-off-by: Li Zhijian <zhijianli88@163.com>
Unmap ptdev BAR when deinit to comply with native system, who zap out
all pre-allocated BARs.
Tracked-On: #1146
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1. In default prescaler, the wdt clock is 1 KHz for a 20-bit counter,
which means approximate 1 second for 10 bits;
2. the default reset timer in seconds need to left shift 10 bits to
represent the value that set to i6300esb register;
Tracked-On: #1142
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
To align with the configuration of the HOST tool, the SW masters
are organized in slices of 8 masters each.
The slice is also the minimal unit to allocate the SW masters for
each UOS.
The patch is to update the parameter checking function.
Tracked-On: #1138
Signed-off-by: Zhi Jin <zhi.jin@intel.com>
Reviewed-by: Chen Gang <gang.c.chen@intel.com>
This patch is used to fix a potential issue resulted from typo.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
When reset VBS-K status should be set to VIRTIO_DEV_INIT_SUCCESS
because at the time the char dev of VBS-K is still opened and
when set_status callback is called later, it depends on
VIRTIO_DEV_INIT_SUCCESS to resume.
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
A new ioctl is introduced in VBS-K to issue reset command to kernel
VBS-K driver. This is used to support VBS-K S3. When FE enters S3
reset command is sent to device model. Backend driver in device model
should use this ioctl to inform the VBS-K drvier in kernel.
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
RPMB frontend driver in UOS kernel has fixed unstable issue,
which requires BE for update as well. E.g. structure adjustment,
definition modification and so on.
Signed-off-by: Deng Wei <wei.a.deng@intel.com>
Signed-off-by: Huang Yang <yang.huang@intel.com>
Acked-by: Zhu Bing <bing.zhu@intel.com>
This patch enable the support for SOS S3 from the perspective
of USB xHCI.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The xHCI emulation greatly depends on the user space library libusb
which is based on the usbfs module in Linux kernel. The libusb will
bind usbfs to physical USB device which makes hardware control over
libusb in user space possible.
The pci_xhci_dev_create is called in pci_xhci_native_usb_dev_conn_cb
which is a callback function triggered by physical USB device plugging.
This function will bind the physical USB device to usbfs in SOS, which
we depend to create the communication between UOS xHCI driver with
physical USB device.
This design will fail if the reconnection happened in the SOS, which
will bind class driver to the physical USB device instead of usbfs,
hence the libusb device handle in DM is invalid.
Currently, the native S3 will disable the vbus for all xHCI ports and
re-drive during S3 resume. This behavior cause native USB driver unbind
the usbfs and bind to related class driver, then made the DM lost
control and failed to continue emulation.
To fix this issue, place the pci_xhci_dev_create in the function
pci_xhci_cmd_enable_slot. According to the xHCI spec 4.5.3 Figure 10,
the UOS always send Enable Slot command when a device is attached or
recovered from errors (by Disable Slot command). So every time the SOS
can't resuming normally or some unexpected disconnection happens, this
desigen will always survive by Disable Slot and Enable Slot command
series from UOS xHCI driver.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Replace 'native_assign_ports' with 'port_map_tbl' to be more accurate
for the role of this variable plays.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The variable native_assign_ports in struct pci_xhci_vdev is used
to record wether certain root hub port in SOS is assigned to UOS.
The logic uses zero to express 'not assigned' and nonzero to express
'assigned'. In this patch, use macro to replace number to express
better.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Currently the maximum number of bus and port for xHCI are
both set to 255, it is theoretically possible but in fact
not neccessary. This patch changes those two values to be
more proper: 4 buses and 20 ports.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Current design cannot get physical USB device information without
the creation of pci_xhci_dev_emu. This brings some difficulties in
certain situations, hence struct usb_native_devinfo is introduced
to describe neccessary information to solve this trouble.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
PORTSC (Port Status and Control Register) register play a very
important role in USB sub-system. This patch is used to refine
related manipulation functions.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Current DM design use two variables to do the indexing of xHCI
Event Ring: er_enq_idx and er_events_cnt. They are members of
the struct pci_xhci_rtsregs.
In UOS, during the process of xHCI resuming, the xHCI driver
will restore the ERSTBA (Event Ring Segment Table Base Address)
register to be the value before suspending. And at this point,
the old DM implementation will set both er_enq_idx and
er_events_cnt to be zero, so the DM will access the Event Ring
from the start position in the buffer. But at the same time the
UOS xHCI driver still wants to access the old position in the
Event Ring before suspending, which will result of unexpected
errors.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This device model is to configure the virtual IPU PCI device.
In order to execute this DM the lauch script needs to add
virtio-ipu as parameter to acrn-dm
For e.g. -s 21,virtio-ipu
Signed-off-by: Bandi,Kushal <kushal.bandi@intel.com>
Randomness sourced from /dev/random which does not block
once it has been seeded at bootup and you will always get
something when you read from that file. This is true on
Freebsd but unfortunately things are not the same on Linux.
Most cases, you can't read anything from /dev/random especially
on current acrn platform which lacking random events.
virtio_rnd inherted from freebsd doesn't work anymore.
This patch makes virtio_rnd working on Linux based SOS. It uses
blocking IO to sevice the front-end random driver and delays the
read operation into a new thread to avoid blocking the main
notify thread.
Signed-off-by: Jie Deng <jie.deng@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
1. support "writeback" and "writethru" mode toggling for virtio-blk
conditionally. When starting DM with "writethru" parameter in
virtio-blk, guest OS could not toggle cache mode. When starting DM
with "writeback" parameter in virtio-blk, guest OS could toggle
cache mode.
------------------------------
DM cmdline | toggle support
------------+-----------------
writeback | yes
writethru | no
------------------------------
2. To toggle cache mode, run below command in guest OS:
echo "write back" > /sys/devices/xxx/vdx/cache_type
OR
echo "write through" > /sys/devices/xxx/vdx/cache_type
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
currently, each virtio device has their own virtio_ops implementation.
Take virtio-blk for example:
static struct virtio_ops virtio_blk_ops = {
"virtio_blk",
1,
sizeof(struct virtio_blk_config),
virtio_blk_reset,
virtio_blk_notify,
virtio_blk_cfgread,
virtio_blk_cfgwrite,
NULL,
NULL,
VIRTIO_BLK_S_HOSTCAPS,
};
If start DM with two virtio-blk, this global variable will be
assigined to two virtio-blk instances. Changing hv_caps for one
instance will affect others. But different instances may need
different capabilities.
To support this requirement, we suggest to move hv_caps to
virtio_base structure, and each instance can return their own
capabilities.
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
With latest FW, ethernet/wifi BDF changes from 3:0.0/4:0.0 to
2:0.0/3:0.0.
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When guest enter/exit S3, we need to do
1. stop watchdog timer when guest enter S3 to avoid watchdog
timer reset guest when guest is in S3 state.
2. reset watchdog timer when guest exit from S3.
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add microframe index register support, which is an important timing
component for isochronous transport.
Change-Id: I615664275b539cfb713d7795edd3f213b0302b92
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Current ring buffer processing logic assumes every transaction
will be submited to physical device before next transaction
coming. So it use two states 0 (free) and 1 (used) to represent
the state of every data block in the ring buffer. With the help
of the two state, the ring buffer could accept and process data
normally.
But this logic is not proper for ISOC transfer, which generally
submits many transactions even none of them arrive the physical
device. So this patch uses three values to represent the state
of data block in the ring buffer:
USB_XFER_BLK_FREE: this block could be filled with new data;
USB_XFER_BLK_HANDLING: this block is submited to physical device
but response from device is still not received;
USB_XFER_BLK_HANDLED: this block has been processed by physical
device.
The new logic will do different things for each state, which will
make the ISOC transfer work successfully.
Change-Id: I5559cae24c739633289742d64dd51751797b81a7
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The xHCI speed emulation is not right, which will cause failure
during enumeration of certain USB device. This patch is used to
fix it.
Change-Id: I2d996298983882ed6921a75a10dec9e8684a393e
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch is used to add support for USB 3.0 devices. Currently
USB 3.0 disk is supported and tested successfully.
Change-Id: I3fbfbe9c28bc4b14af0417104f8fa822f9758908
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Original code will reset the whole USB device when xHCI Reset
Endpoint command is received, this behavior is not right. This
patch is used to fix it.
And according to xhci spec 4.6.8, if the endpoint is not in the
halted state, xHC should reject to execute this command and the
Context State Error should be returned. This patch also add this
logic.
Change-Id: I55a5918148d82d103fb3eb27d582f9676f9f61d3
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Mainly change the logs for transfer submission and completion,
which are very important parts in USB emulation code.
Change-Id: I4e04f1426e164ca3693e70946ed51380201e49ee
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This function add high level reset_vdev function. Which is
implemented to call deinit/init pairing to emulate the virtual
device reset operation.
This patch also add the system reset which keep the UOS RAM
content functionality to DM.
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Guest has erquirement to support system/full reboot and S3. Which could
trigger different reset path in guest
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
We should keep variable name in function declaration. It makes
things clearer and easier to be understood.
Signed-off-by: Jie Deng <jie.deng@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
There has one new DRD driver followed usb role framework which is just
upstreamed to Linux community. This patch updates the xHCI DM to be
compatible with it. DM DRD code follows DRD spec to implement and make
it more reasonable.
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Reviewed-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
For dedicated xHCI extended capability, it need set corresponding PCI VID/PID.
This patch sets the Intel Apollo Lake platform PCI VID/PID for DRD
capability which will be checked for enabling DRD fucntion in new DRD
driver. Besides, this patch refines the PCI VID/PID related code.
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Reviewed-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
6300esb has bit in its register to show whether the watchdog
timeout is hit.
This patch adds this bit support. So the guest could query
whether last reset is triggered by watchdog reset.
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Reviewed-by: Cao Minggui <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Tested-by: Binbin Wu <binbin.wu@intel.com>
The lpc dm causes that UOS can't boot if the parameters are set incorrectly,
it is not friendly to users.
This patch optimizes the lpc error handle flow. UOS always can boot successfully
whatever the lpc settings are.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
WIFI dev has no FLR, so 'reset' in sysfs calls secondary bus reset,
which cause PCI configuration mess(all FF) then passthrough failure.
To fix it, this patch makes no reset before passthrough by default,
until append this option.
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Current option of removing vGSI capability is global, which exposes
vIOAPIC link for all ptdev even only one need this. This patch makes
it as ptdev local option to lower the system level impact. To keep
vGSI for MSI capable ptdev, just explicitly append ",keep_gsi" in
option list, like "-s 14,passthru,0/e/0,keep_gsi"
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Previously, either rnd->fd or vbs_k->fd isn't be closed in some cases.
this patch will close them in time.
V2: fix vbs_k->fd leak as well
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
- hardcode the devices' GSI info based on the platform
- reject the passthrough if the following requirement is not met
all the PCI devices that are sharing the same GSI should be assigned
to same VM to avoid physical GSI sharing between multiple VMs.
v4 -> v5
* Move the gsi_dev_mapping_tables definition in a separate file
* Add the GSI info that might be used by GPIO
* Update the HW name
v3 - > v4
* Refine the format of raw data to improve the readability
* Remove the redundant code when adding the new dev into the gsi
sharing group
v2 -> v3
* Add the MSI/MSI-x capability check
Do not add the device which supports MSI/MSI-x to the GSI sharing
group.
v1 -> v2
* Update the GSI raw data based on SBL
* Free the resources when gsi sharing violation occurs
* Move the MACRO PCI_BDF(b, d, f) to pci_core.h since passthrough.c
and gsi_sharing.c are both using it
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
Reviewed-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The device model is a userspace application on SOS to config the
PCI devices for the UOS. Audio mediator device model is to config
the virtual audio PCI device.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
When enabling GPU passthru for guest, stolen memory needs to be
disabled. This change disables stolen memory in passthru mode.
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Reviewed-by: Gong Zhipeng <zhipeng.gong@intel.com>
To enable GPU passthru, BAR2 allocation had problems when the allocation
is above the 4GB memory.This change is to accomodate the 256MB aperture
allocation in BAR2 to a more managable address.
v2: changed the MEMBASE64 address instead of increasing the mem_size.
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Reviewed-by: Gong Zhipeng <zhipeng.gong@intel.com>
