The ve820 table' hpa1_low area is divided into two parts, which
is making the code too complicated and causing problems. Moving
the entries that divides the hpa1_low could make things easier.
This patch moves the GPU OpRegion to the tail area of 2G,
consecutive to the acpi data/nvs area.
before:
|<---low_1M--->|
|<---hpa1_low_part1--->|
|<---SSRAM--->|
|<---GPU_OpRegion--->|
|<---hpa1_low_part2--->|
|<---ACPI DATA--->|
|<---ACPI NVS--->|
---2G---
after:
|<---low_1M--->|
|<---hpa1_low_part1--->|
|<---SSRAM--->|
|<---hpa1_low_part2--->|
|<---GPU_OpRegion--->|
|<---ACPI DATA--->|
|<---ACPI NVS--->|
---2G---
Tracked-On: #6674
Signed-off-by: Zhou, Wu <wu.zhou@intel.com>
Reviewed-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
The length of the ACPI data entry in ve820 tab was 960K, while the
ACPI file is 1MB. It causes the ACPI file copy failed due to reserved
ACPI regions in ve820 table is not enough when loading pre-launched
VMs. This patch changes ACPI data area to 1MB to fix the problem.
And the ACPI data length was missed when calculating
ENTRY_HPA1_LOW_PART2 length. Fixed here too.
Also adds some refinement to the hard-coded ACPI base/addr definations
Tracked-On: #6674
Signed-off-by: Zhou, Wu <wu.zhou@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
Rename gpa_uos to gpa_user_vm
rename base_gpa_in_uos to base_gpa_in_user_vm
rename UOS_VIRT_PCI_MMCFG_BASE to USER_VM_VIRT_PCI_MMCFG_BASE
rename UOS_VIRT_PCI_MMCFG_START_BUS to USER_VM_VIRT_PCI_MMCFG_START_BUS
rename UOS_VIRT_PCI_MMCFG_END_BUS to USER_VM_VIRT_PCI_MMCFG_END_BUS
rename UOS_VIRT_PCI_MEMBASE32 to USER_VM_VIRT_PCI_MEMBASE32
rename UOS_VIRT_PCI_MEMLIMIT32 to USER_VM_VIRT_PCI_MEMLIMIT32
rename UOS_VIRT_PCI_MEMBASE64 to USER_VM_VIRT_PCI_MEMBASE64
rename UOS_VIRT_PCI_MEMLIMIT64 to USER_VM_VIRT_PCI_MEMLIMIT64
rename UOS in comments message to User VM.
Tracked-On: #6744
Signed-off-by: Liu Long <long.liu@linux.intel.com>
Reviewed-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Rename sos_vm to service_vm.
rename sos_vmid to service_vmid.
rename sos_vm_ptr to service_vm_ptr.
rename get_sos_vm to get_service_vm.
rename sos_vm_gpa to service_vm_gpa.
rename sos_vm_e820 to service_vm_e820.
rename sos_efi_info to service_vm_efi_info.
rename sos_vm_config to service_vm_config.
rename sos_vm_hpa2gpa to service_vm_hpa2gpa.
rename vdev_in_sos to vdev_in_service_vm.
rename create_sos_vm_e820 to create_service_vm_e820.
rename sos_high64_max_ram to service_vm_high64_max_ram.
rename prepare_sos_vm_memmap to prepare_service_vm_memmap.
rename post_uos_sworld_memory to post_user_vm_sworld_memory
rename hcall_sos_offline_cpu to hcall_service_vm_offline_cpu.
rename filter_mem_from_sos_e820 to filter_mem_from_service_vm_e820.
rename create_sos_vm_efi_mmap_desc to create_service_vm_efi_mmap_desc.
rename HC_SOS_OFFLINE_CPU to HC_SERVICE_VM_OFFLINE_CPU.
rename SOS to Service VM in comments message.
Tracked-On: #6744
Signed-off-by: Liu Long <long.liu@linux.intel.com>
Reviewed-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
In current design, when pass-thru dev,
for the PIO bar, need to ensure the guest PIO start address
equals to host PIO start address.
Then set the VMCS io bitmap to pass-thru the corresponding
port io to guest for performance.
ACRN-DM and acrn-config should ensure the identical mapping of PIO bar.
If ACRN-DM or acrn-config failed to achieve this,
we should deny the launch of VM
Tracked-On: #6508
Signed-off-by: Liu,Junming <junming.liu@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Relocate ACPI address to 0x7fe00000 and ACPI NVS to 0x7ff00000 correspondingly.
In this case, we could include TPM event log region [0x7ffb0000, 0x80000000)
into ACPI NVS.
Tracked-On: #6320
Signed-off-by: Fei Li <fei1.li@intel.com>
IC_ADD_HV_VDEV -> ACRN_IOCTL_CREATE_VDEV
IC_REMOVE_HV_VDEV -> ACRN_IOCTL_DESTROY_VDEV
struct acrn_emul_dev -> struct acrn_vdev
Also, move struct acrn_vdev to acrn_common.h as this structure is used
by both DM and HV.
Tracked-On: #6282
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
IC_ASSIGN_PCIDEV -> ACRN_IOCTL_ASSIGN_PCIDEV
IC_DEASSIGN_PCIDEV -> ACRN_IOCTL_DEASSIGN_PCIDEV
QUIRK_PTDEV -> ACRN_PTDEV_QUIRK_ASSIGN
struct acrn_assign_pcidev -> struct acrn_pcidev
Move struct acrn_pcidev into acrn_common.h because it is used by both
DM and HV.
Tracked-On: #6282
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
When guest doing BAR re-programming, we should check whether
the base address of the BAR is valid.This patch does this check by:
1. whether the gpa is located in the responding MMIO window
2. whether the gpa is aligned with the BAR size
Tracked-On: #6011
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Li Fei <fei1.li@intel.com>
Create virtual root port through add_vdev hypercall. add_vdev
identifies the virtual device to add by its vendor id and device id, then
call the corresponding function to create virtual device.
-create_vrp(): Find the right virtual root port to create
by its secondary bus number, then initialize the virtual root port.
And finally initialize PTM related configurations.
-destroy_vrp(): nothing to destroy
Tracked-On: #5915
Signed-off-by: Rong Liu <rong.l.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Acked-by: Jason Chen <jason.cj.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Add virtual root port that supports the most basic pci-e bridge and root port operations.
- init_vroot_port(): init vroot_port's basic registers.
- deinit_vroot_port(): reset vroot_port
- read_vroot_port_cfg(): read from vroot_port's virtual config space.
- write_vroot_port_cfg(): write to vroot_port's virtual config space.
Tracked-On: #5915
Signed-off-by: Rong Liu <rong.l.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Acked-by: Jason Chen <jason.cj.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Instead of "#include <x86/foo.h>", use "#include <asm/foo.h>".
In other words, we are adopting the same practice in Linux kernel.
Tracked-On: #5920
Signed-off-by: Liang Yi <yi.liang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Requires explicit arch path name in the include directive.
The config scripts was also updated to reflect this change.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The commit 'Fix: HV: VM OS failed to assign new address to pci-vuart
BARs' need more reshuffle.
Tracked-On: #5491
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Signed-off-by: Eddie Dong <eddie.dong@intel.com>
When wrong BAR address is set for pci-vuart, OS may assign a
new BAR address to it. Pci-vuart BAR can't be reprogrammed,
for its wrong fixed value. That can may because pci_vbar.fixed and
pci_vbar.type has overlap in abstraction, pci_vbar.fixed
has a confusing name, pci_vbar.type has PCIBAR_MEM64HI which is not
really a type of pci BARs.
So replace pci_vbar.type with pci_vbar.is_mem64hi, and change
pci_vbar.fixed to an union type with new name pci_vbar.bar_type.
Tracked-On: #5491
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Add cteate method for vmcs9900 vdev in hypercalls.
The destroy method of ivshmem is also suitable for other emulated vdev,
move it into hcall_destroy_vdev() for all emulated vdevs
Tracked-On: #5394
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
if vuart type is pci-vuart, then use MSI interrupt
split vuart_toggle_intr() control flow into vuart_trigger_level_intr() &
trigger_vmcs9900_msix(), because MSI is edge triggered, no deassertion
operation. Only trigger MSI for pci-vuart when assert interrupt.
Tracked-On: #5394
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
support pci-vuart type, and refine:
1.Rename init_vuart() to init_legacy_vuarts(), only init PIO type.
2.Rename deinit_vuart() to deinit_legacy_vuarts(), only deinit PIO type.
3.Move io handler code out of setup_vuart(), into init_legacy_vuarts()
4.add init_pci_vuart(), deinit_pci_vuart, for one pci vuart vdev.
and some change from requirement:
1.Increase MAX_VUART_NUM_PER_VM to 8.
Tracked-On: #5394
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
The vuart_read()/vuart_write() are coupled with PIO vuart type. Move
the non-type related code into vuart_read_reg()/vuart_write_reg(), so
that we can re-use them to handle MMIO request of pci-vuart type.
Tracked-On: #5394
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch enables doorbell feature for hv-land
ivshmem device to support interrupt notification
between VMs that use inter-VM(ivshmem) devices.
Tracked-On: #5407
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Li, Fei <fei1.li@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Per PCI Firmware Specification Revision 3.0, 4.1.2. MCFG Table Description:
Memory Mapped Enhanced Configuration Space Base Address Allocation Structure
assign the Start Bus Number and the End Bus Number which could decoded by the
Host Bridge. We should not access the PCI device which bus number outside of
the range of [Start Bus Number, End Bus Number).
For ACRN, we should:
1. Don't detect PCI device which bus number outside the range of
[Start Bus Number, End Bus Number) of MCFG ACPI Table.
2. Only trap the ECAM MMIO size: [MMCFG_BASE_ADDRESS, MMCFG_BASE_ADDRESS +
(End Bus Number - Start Bus Number + 1) * 0x100000) for SOS.
Tracked-On: #5233
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The old method of build pre-launched VM vacpi by HV source code is deprecated,
so remove related source code;
Tracked-On: #5266
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously we use a pre-defined structure as vACPI table for pre-launched
VM, the structure is initialized by HV code. Now change the method to use a
pre-loaded multiboot module instead. The module file will be generated by
acrn-config tool and loaded to GPA 0x7ff00000, a hardcoded RSDP table at
GPA 0x000f2400 will point to the XSDT table which at GPA 0x7ff00080;
Tracked-On: #5266
Signed-off-by: Victor Sun <victor.sun@intel.com>
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously the ACPI table was stored in F segment which might not be big
enough for a customized ACPI table, hence reserve 1MB space in pre-launched
VM e820 table to store the ACPI related data:
0x7ff00000 ~ 0x7ffeffff : ACPI Reclaim memory
0x7fff0000 ~ 0x7fffffff : ACPI NVS memory
Tracked-On: #5266
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When HV pass through the P2SB MMIO device to pre-launched VM, vgpio
device model traps MMIO access to the GPIO registers within P2SB so
that it can expose virtual IOAPIC pins to the VM in accordance with
the programmed mappings between gsi and vgsi.
Tracked-On: #5246
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
For ivshmem vdev creation, the vdev vBDF, vBARs, shared memory region
name and size are set by device model. The shared memory name and size
must be same as the corresponding device configuration which is configured
by offline tool.
v3: add a comment to the vbar_base member of the acrn_vm_pci_dev_config
structure that vbar_base is power-on default value
Tracked-On: #4853
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Ivshmem device defines four registers including Interrupt Mask, Interrupt
Status, IVPostion and Doorbell. The first two are useless and no emulation
is required. The latter two are used for interrupts and will be implemented
in the future.
This patch also introduces a new priv_data member for structure pci_vdev,
it can be used to find an ivshmem device through pci_vdev.
v2: refine code style
v3: 1) add @pre for ivshmem_mmio_handler function
2) refine code style
v4: 1) set ivshmem registers default value when vBAR mapping
2) change find_ivshmem_device to set_ivshmem_device
v5: 1) change set_ivshmem_device to find_and_set_ivshmem_device
2) add a ASSERT to check if the vdev->priv_data is set successfully
v6: change find_and_set_ivshmem_device to create_ivshmem_device
Tracked-On: #4853
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Ivshmem device is used for shared memory based communication between
pre-launched/post-launched VMs.
this patch implements ivshmem device configuration space initialization
and ivshmem device operation methods.
v2: introduce init_one_pcibar interface to simplify BAR initialization
operation of HV emulated PCI device.
v3: 1) due to init_one_pcibar API is only used for pre-launched VM vdevs
it can't be applied to all vdevs, so remove it.
2) move ivshmem BARs initialization to subsequent patch, this patch
only introduce ivshmem configuration space initialization.
Tracked-On: #4853
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The ivshmem memory regions use the memory of the hypervisor and
they are continuous and page aligned.
this patch is used to initialize each memory region hpa.
v2: 1) if CONFIG_IVSHMEM_SHARED_MEMORY_ENABLED is not defined, the
entire code of ivshmem will not be compiled.
2) change ivshmem shared memory unit from byte to page to avoid
misconfiguration.
3) add ivshmem configuration and vm configuration references
v3: 1) change CONFIG_IVSHMEM_SHARED_MEMORY_ENABLED to CONFIG_IVSHMEM_ENABLED
2) remove the ivshmem configuration sample, offline tool provides default
ivshmem configuration.
3) refine code style.
v4: 1) make ivshmem_base 2M aligned.
Tracked-On: #4853
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
-- move vm_state_lock to other place in vm structure
to avoid the memory waste because of the page-aligned.
-- remove the memset from create_vm
-- explicitly set max_emul_mmio_regions and vcpuid_entry_nr to 0
inside create_vm to avoid use without initialization.
-- rename max_emul_mmio_regions to nr_emul_mmio_regions
v1->v2:
add deinit_emul_io in shutdown_vm
Tracked-On: #4958
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Grandhi, Sainath <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
On WHL platform, we need to pass through TPM to Secure pre-launched VM. In order
to do this, we need to add TPM2 ACPI Table and add TPM DSDT ACPI table to include
the _CRS.
Now we only support the TPM 2.0 device (TPM 1.2 device is not support). Besides,
the TPM must use Start Method 7 (Uses the Command Response Buffer Interface)
to notify the TPM 2.0 device that a command is available for processing.
Tracked-On: #5053
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Add two hypercalls to support MMIO device pass through for post-launched VM.
And when we support MMIO pass through for pre-launched VM, we could re-use
the code in mmio_dev.c
Tracked-On: #5053
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Some OSes assume the platform must have the IOAPIC. For example:
Linux Kernel allocates IRQ force from GSI (0 if there's no PIC and IOAPIC) on x86.
And it thinks IRQ 0 is an architecture special IRQ, not for device driver. As a
result, the device driver may goes wrong if the allocated IRQ is 0 for RTVM.
This patch expose vIOAPIC to RTVM with LAPIC passthru even though the RTVM can't
use IOAPIC, it servers as a place holder to fullfil the guest assumption.
After vIOAPIC has exposed to guest unconditionally, the 'ready' field could be
removed since we do vIOAPIC initialization for each guest.
Tracked-On: #4691
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
hv: pci: refine pci_find_vdev with hash
1. Refined pci_find_vdev with BDF-hashing for better performance
Tracked-On: #4857
Signed-off-by: Wang Qian <qian1.wang@intel.com>
Reviewed-by: Li Fei <Fei1.Li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Some passthrough devices require multiple MSI vectors, but don't
support MSI-X. In meanwhile, Linux kernel doesn't support continuous
vector allocation.
On native platform, this issue can be mitigated by IOMMU via interrupt
remapping. However, on ACRN, there is no vIOMMU.
vMSI-X on MSI emulation is one solution to mitigate this problem on ACRN.
This patch adds MSI-X emulation on MSI capability.
For the device needs to do MSI-X emulation, HV will hide MSI capability
and present MSI-X capability to guest.
The guest driver may need to modify to reqeust MSI-X vector.
For example:
ret = pci_alloc_irq_vectors(pdev, 1, STMMAC_MSI_VEC_MAX,
- PCI_IRQ_MSI);
+ PCI_IRQ_MSI | PCI_IRQ_MSIX);
To enable MSI-X emulation, the device should:
- 1. The device should be in vmsix_on_msi_devs array.
- 2. Support MSI, but don't support MSI-X.
- 3. MSI capability should support per-vector mask.
- 4. The device should have an unused BAR.
- 5. The device driver should not rely on PBA for functionality.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The existing code do separately for each VM when we deinit vpci of a VM. This is
not necessary. This patch use the common handling for all VMs: we first deassign
it from the (current) user, then give it back to its parent user.
When we deassign the vdev from the (current) user, we would de-initialize the
vMSI/VMSI-X remapping, so does the vMSI/vMSI-X data structure.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong<eddie.dong@Intel.com>
Add a new field 'parent_user' to record the parent user of the vdev. And refine
'new_owner' to 'user' to record who is the current user of the vdev. Like
-----------------------------------------------------------------------------------------------
vdev in | HV | pre-VM | SOS | post-VM
| | |vdev used by SOS|vdev used by post-VM|
-----------------------------------------------------------------------------------------------
parent_user| NULL(HV) | NULL(HV) | NULL(HV) | NULL(HV) | vdev in SOS
-----------------------------------------------------------------------------------------------
user | vdev in HV | vdev in pre-VM | vdev in SOS | vdev in post-VM | vdev in post-VM
-----------------------------------------------------------------------------------------------
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong<eddie.dong@Intel.com>
Most code in the if ... else is duplicated. We could put it out of the
conditional statement.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Add FADT table support to support guest S5 setting.
According to ACPI 6.3 Spec, OSPM must ignored the DSDT and FACS fields if them're zero.
However, Linux kernel seems not to abide by the protocol, it will check DSDT still.
So add an empty DSDT to meet it.
Tracked-On: #4623
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Conceptually, the devices unregistration sequence of the shutdown process should be
opposite to create.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
