The break key (key value 0x0) was used as switch key from guest serial
to hv console and guest serial could not receive break key. This blocked
some guest debugging features like KGDB/KDB, sysrq, etc.
This patch leverages escape sequence "<escape> + <break>" to send break to
guest and "<escape> + e" to switch from guest serial to hv console.
Tracked-On: #8583
Signed-off-by: Qiang Zhang <qiang4.zhang@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
1) region ID shall be configured by user via config tool.
2) region ID is programmed to "Subsystem ID" of PCI config space.
2) "Subsystem Vendor ID" is harded coded as 0x8086
Tracked-On: #8566
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
This patch adds ivshmem region ID configuration support when user
configure ACRN IVSHMEM devices via ACRN config tool, this ID provides
VMs with a stable identification of multiple shared memory regions.
Also add logic to generate launch script with region ID configured
as below:
`add_virtual_device 8 ivshmem hv:/shm_region_0,256,1`
Tracked-On: #8566
Signed-off-by: Kunhui-Li <kunhuix.li@intel.com>
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
sbuf_put copies sbuf->ele_size of data, and puts into ring. Currently
this function assumes that data size from caller is no less than
sbuf->ele_size.
But as sbuf->ele_size is usually setup by some sources outside of the HV
(e.g., the service VM), it is not meant to be trusted. So caller should
provide the max length of the data for safety reason. sbuf_put() will
return UINT32_MAX if max_len of data is less than element size.
Additionally, a helper function sbuf_put_many() is added for putting
multiple entries.
Tracked-On: #8547
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
When a guest OS performs an RTC change action, we wish this event be
captured by developers, and then they can decide what to do with it.
(e.g., whether to change physical RTC)
There are some facts that makes RTC change event a bit complicated:
- There are 7 RTC date/time regs (year, month…). They can only be
updated one by one.
- RTC time is not reliable before date/time update is finished.
- Guests can update RTC date/time regs in any order.
- Guests may update RTC date/time regs during either RTC halted or not
halted.
A single date/time update event is not reliable. We have to wait for
the guest to finish the update process. So the DM's event handler
sets up a timer, and wait for some time (1 second). If no more change
happens befor the timer expires, we can conclude that the RTC
change has been done. Then the rtc change event is emitted.
This logic of event handler can be used to process HV vrtc time change
event too.
Tracked-On: #8547
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Jian Jun Chen <jian.jun.chen@intel.com>
This patch creates a thread for vm_event delivery. The thread uses epoll
to poll event notifications, then read out the msg data queued in sbuf.
An event handler is called upon success receiving. Both HV and DM event
sources share the same process.
Also vm_event tx API for DM event source is added in this patch.
Tracked-On: #8547
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Jian Jun Chen <jian.jun.chen@intel.com>
This patch creates vm_event support in HV, including:
1. Create vm_event data type.
2. Add vm_event sbuf and its initializer. The sbuf will be allocated by
DM in Service VM. Its page address will then be share to HV through
hypercall.
3. Add an API to send the HV generated event.
Tracked-On: #8547
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Add four per-vm bvt parameters as the initial bvt parameter values for
vCPU threads.
- bvt_weight
The time sharing of a thread on CPU.
- bvt_warp_value
Boost value of virtual time of a thread (time borrowed from future) to
reduce Effective Virtual Time to prioritize the thread.
- bvt_warp_limit
Max warp time in one warp.
- bvt_unwarp_period
Min unwarp time after a warp.
Tracked-On: #8500
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Qiang Zhang <qiang4.zhang@intel.com>
Abstract out schedulers config data for vCPU threads and other hypervisor
threads to sched_params structure. And it's used to initialize per
thread scheduler private data. The sched_params for vCPU threads come
from vm_config generated by config tools while other hypervisor threads
need give them explicitly.
Tracked-On: #8500
Signed-off-by: Qiang Zhang <qiang4.zhang@intel.com>
Add clamp macro to clamp a value within a range.
Tracked-On: #8500
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Qiang Zhang <qiang4.zhang@intel.com>
When all vCPU threads on one pCPU are put to sleep (e.g., when all
guests execute HLT), hv would schedule to idle thread. Currently the
idle thread executes PAUSE which does not enter any c-state and consumes
a lot of power. This patch is to support HLT in the idle thread.
When we switch to HLT, we have to make sure events that would wake a
vCPU must also be able to wake the pCPU. Those events are either
generated by local interrupt or issued by other pCPUs followed by an
ipi kick.
Each of them have an interrupt involved, so they are also able to wake
the halted pCPU. Except when the pCPU has just scheduled to idle thread
but not yet halted, interrupts could be missed.
sleep-------schedule to idle------IRQ ON---HLT--(kick missed)
^
wake---kick|
This areas should be protected. This is done by a safe halt
mechanism leveraging STI instruction’s delay effect (same as Linux).
vCPUs with lapic_pt or hv with CONFIG_KEEP_IRQ_DISABLED=y does not allow
interrupts in root mode, so they could never wake from HLT (INIT kick
does not wake HLT in root mode either). They should continue using PAUSE
in idle.
Tracked-On: #8507
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
~0UL is widely used to specify the maximum memory size
when calling e820_alloc_memory(), this patch to define
a MACRO for it to avoid using this magic number.
Tracked-On: #8502
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
For a pdev which allocated to prelaunched VM or owned by HV, we need to check
whether it is a multifuction dev at function 0. If yes we have to emulate a
dummy function dev in Service VM, otherwise the sub-function devices will be
lost in guest OS pci probe process.
Tracked-On: #8492
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Qiang Zhang <qiang4.zhang@intel.com>
Signed-off-by: Victor Sun <victor.sun@intel.com>
When we do init_all_dev_config() in pci.c, the pdevs added to pci dev_config
will be exposed to Service VM or passthru to prelauched VM. The original code
would find service VM config in every pci pdev init loop, this is unnecessary
and definitely impact performance. Here we generate Service VM config pointer
with config tool so that init_one_dev_config() could refer service VM config
directly.
Tracked-On: #8491
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Qiang Zhang <qiang4.zhang@intel.com>
Signed-off-by: Victor Sun <victor.sun@intel.com>
doxygen will warn that documented return type is found for functions
that does not return anything in 1.9.4 or later versions. 'None' is
not a special keyword in doxyge, it will recognize it as description
to the return value that does not exist in void functions.
Tracked-On: #8425
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
The Hardware Feedback Interface (HFI) and Intel® Thread Director (ITD)
features require OS to provide a physical page address to
IA32_HW_FEEDBACK_PTR. Then the hardware will update the processor
information to the page address. The issue is that guest VM will program
its GPA to that MSR, causing great risk of tempering memory.
So HFI and ITD should be made invisible to guests, until we provide
proper virtulization of those features.
Tracked-On: #8463
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
arch/x86/guest/nested.c, where nested_vmexit_handler() is defined, is
only compiled when CONFIG_NVMX_ENABLED is enabled. Define a dummy
function in include/arch/x86/asm/guest/nested.h to fix the undefined
reference linker error.
Tracked-On: #8465
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
According to SDM Vol3 11.12.10, in x2APIC mode, Logical Destination has
two parts:
- Cluster ID (LDR[31:16])
- Logical ID (LDR[15:0])
Cluster ID is a numerical address, while Logical ID is a 16bit mask. We
can only use Logical ID to address multi destinations within a Cluster.
So we can't just 'or' all the Logical Destination in LDR registers to
get one mask for all target pCPUs. This would get a wrong destination
mask if the target Destinations are from different Clusters.
For example in ADL/RPL x2APIC LDRs for core 2-5 are 0x10001 0x10100
0x20001 0x20100. If we 'or' them together, we would get a Logical
Destination of 0x30101, which points to core 6 and another core.
If core 6 is running a RTVM, then the irq is unable to get to
core 2-5, causing the guest on core 2-5 driver fail.
Guests working in xAPIC mode may use 'Flat Model' to select an
arbitrary list of CPUs as its irq destination. HV may not be able to
include them all when transfering to physical destinations, because
the HW is working in x2APIC mode and can only use 'Cluster Model'.
There would be no perfect fix for this issue. This patch is a simple
fix, by just keep the first Cluster of all target Logical Destinations.
Tracked-On: #8435
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
On x86 platform, the upper 16 bit of I/O BAR should be initialized to
zero by BIOS. Howerever, some buggy BIOS still programs the upper 16
bits to non-zero, which causes error in check_pt_dev_pio_bars(). Since
I/O BAR reprogramming by VM is currently unsupported, this patch
ignores such I/O BARs when creating vpci devices to make VM boot.
Tracked-On: #8373
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Thermal events are delivered through lapic thermal LVT. Currently
ACRN does not support delivering those interrupts to guests by
virtual lapic. They need to be virtualized to provide guests some
thermal management abilities. Currently we just hide thermal
lvt from guests, including:
1. Thermal LVT:
There is no way to hide thermal LVT from guests. But we need do
something to make sure no interrupt can be actually trigered:
- skip thermal LVT in vlapic_trigger_lvt()
- trap-and-emulate thermal LVT in lapic-pt mode
2. As We have plan to introduce virtualization of thermal monitor in the
future, we use a vm flag GUEST_FLAG_VTM which is default 0 to control
the access to it. So that it can help enabling VTM in the future.
Tracked-On: #8414
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Changes made by this patch includes:
1. Emulate HWP and pstate MSRs/CPUIDs. Those are exposed to guest when
the GUEST_FLAG_VHWP is set:
- CPUID[6].EAX[7,9,10]: MSR_IA32_PM_ENABLE(enabled by hv, always read
1), MSR_IA32_HWP_CAPABILITIES, MSR_IA32_HWP_REQUEST,
MSR_IA32_HWP_STATUS,
- CPUID[6].ECX[0]: MSR_IA32_MPERF, MSR_IA32_APERF
- MSR_IA32_PERF_STATUS(read as base frequency when not owning pCPU)
- MSR_IA32_PERF_CTL(ignore writes)
2. Always hide HWP interrupt and package control MSRs/CPUIDs:
- CPUID[6].EAX[8]: MSR_IA32_HWP_INTERRUPT(currently ACRN is not able
to deliver thermal LVT virtual interrupt to guests)
- CPUID[6].EAX[11,22]: MSR_IA32_HWP_REQUEST_PKG, MSR_IA32_HWP_CTL
Tracked-On: #8414
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Currently CPU frequency control is hidden to guests, and controlled
by hypervisor. While it is sufficient in most cases, some guest OS may
still need CPU performance info to make multi-core scheduling decisions.
This is seen on Linux kernel, which uses HWP highest performance level
as CPU core's priority in multi-core scheduling (CONFIG_SCHED_MC_PRIO).
Enabling this kernel feature could improve performance as single thread
workloads are scheduled on the highest performance cores. This is
significantly useful for guests with hybrid cores.
The concept is to expose performance interface to guest who exclusively
owns pCPU assigned to it. So that Linux guest can load intel_pstate
driver which will then provide the kernel with each core's schedule
priority.
Intel_pstate driver also relies on CONFIG_ACPI_CPPC_LIB to implement
this mechanic, this means we also need to provide ACPI _CPC in DM.
This patch sets up a guest flag GUEST_FLAG_VHWP to indicate whether
the guest can have VHWP feature.
Tracked-On: #8414
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
This patch emulates the PLATFORM_INFO MSR in hypervisor to make it
only visible to Service VM, and only processor ratios (bit 15:8,
47:40 and 55:48) and sample part bit (27) are exponsed. This is
intended to prevent Service VM from changing processor parameters
like turbo ratio.
Tracked-On: #8406
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
When assigning a physical interrupt to a Post-launched VM, if it has
been assigned to ServiceVM, we should remove that mapping first to reset
ioapic pin state and rte, and build new mapping for the Post-launched
VM.
Tracked-On: #8370
Signed-off-by: Qiang Zhang <qiang4.zhang@linux.intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When CPU support MONITOR/MWAIT, OS prefer to use it enter
deeper C-state.
Now ACRN pass through MONITOR/MWAIT to guest.
For vCPUs (ie vCPU A and vCPU B) share a pCPU, if vCPU A uses MWait to enter C state,
vCPU B could run only after the time slice of vCPU A is expired. This time slice of
vCPU A is gone to waste.
For Local APIC pass-through (used for RTVM), the guest pay more attention to
timeliness than power saving.
So this patch hides MONITOR/MWAIT by:
1. Clear vCPUID.05H, vCPUID.01H:ECX.[bit 3] and
MSR_IA32_MISC_ENABLE_MONITOR_ENA to tell the guest VM's vCPU
does not support MONITOR/MAIT.
2. Enable MSR_IA32_MISC_ENABLE_MONITOR_ENA bit for
MSR_IA32_MISC_ENABLE inject 'GP'.
3. Trap instruction 'MONITOR' and 'MWAIT' and inject 'UD'.
4. Clear vCPUID.07H:ECX.[bit 5] to hide 'UMONITOR/UMWAIT'.
5. Clear "enable user wait and pause" VM-execution control, so
UMONITOR/MWAIT causes an 'UD'.
Tracked-On: #8253
Signed-off-by: Yuanyuan Zhao <yuanyuan.zhao@linux.intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Exclude "GUEST_FLAG_PMU_PASSTHROUGH" from DM_OWNED_GUEST_FLAG_MASK
in case device model rewrite the value in release mode, reserve it
in debug mode.
Signed-off-by: hangliu1 <hang1.liu@linux.intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Tracked-On:#6690
The current code would write 'BAR address & size_maks' into PCIe virtual
BAR before updating the virtual BAR's base address when guest writing a
PCIe device's BAR. If the size of a PCIe device's BAR is larger than 4G,
the low 32 bits size_mask for this 64 bits BAR is zero. When ACRN updating
the virtual BAR's base address, the low 32 bits sizing information would
be lost.
This patch saves whether a BAR writing is sizing or not before updating the
virtual BAR's base address.
Tracked-On: #8267
Signed-off-by: Fei Li <fei1.li@intel.com>
When guest traps and wants to access a mmio region, the ACRN hypervisor
doesn't know the mmio size the guest wants to access until the trap
happens. In this case, ACRN should switch the mmio size and then call
mmio_read8/16/32/64 or mmio_write8/16/32/64 in each trap place.
This patch wrap the mmio read/write with a parameter to assign the mmio
size.
Tracked-On: #8255
Signed-off-by: Fei Li <fei1.li@intel.com>
The design of ACRN CPU performance management is to let hardware
do the autonomous frequency selection(or set to a fixed value),
and remove guest's ability to control CPU frequency.
This patch is to implement the CPU frequency initializer, which will
setup CPU frequency base on the performance policy type.
Two performance policy types are provided for user to choose from:
- 'Performance': CPU runs at its CPU runs at its maximum frequency.
Enable hardware autonomous frequency selection if HWP is presented.
- 'Nominal': CPU runs at its guaranteed frequency.
The policy type is passed to hypervisor through boot parameter, as
either 'cpu_perf_policy=Nominal' or 'cpu_perf_policy=Performance'.
The default type is 'Performance'.
Both HWP and ACPI p-state are supported. HWP is the first choice, for
it provides hardware autonomous frequency selection, while keeps
frequency transaction time low.
Two functions are added to the hypervisor to call:
- init_frequency_policy(): called by BSP at start up time. It processes
the boot parameters, and enables HWP if it is presented.
- apply_frequency_policy(): called after init_frequency_policy().
It applies initial CPU frequency policy setting for each core. It
uses a set of frequency limits data struct to quickly decide what the
highest/nominal frequency is. The frequency limits are generated by
config-tools.
The hypervisor will not be governing CPU frequency after initial policy
is applied.
Cores running RTVMs are fixed to nominal/guaranteed frequency, to get
more certainty in latency. This is done by setting the core's frequency
limits to highest=lowest=nominal in config-tools.
Tracked-On: #8168
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
For an IO request, hv will check if it was registered in asyncio desc
list. If yes, put the corresponding fd to the shared buffer. If the
shared buffer is full, yield the vcpu and try again later.
Tracked-On: #8209
Signed-off-by: Conghui <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add hypercall to add/remove asyncio request info. Hv will record the
info in a list, and when a new ioreq is come, hv will check if it is
in the asyncio list, if yes, queue the fd to asyncio buffer.
Tracked-On: #8209
Signed-off-by: Conghui <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Current IO emulation is synchronous. The user VM need to wait for the
completion of the the I/O request before return. But Virtio Spec
introduces introduces asynchronous IO with a new register in MMIO/PIO
space named NOTIFY, to be used for FE driver to notify BE driver, ACRN
hypervisor can emulate this register by sending a notification to vCPU
in Service VM side. This way, FE side can resume to work without waiting
for the full completion of BE side response.
Tracked-On: #8209
Signed-off-by: Conghui <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Extend sbuf hypercall to support other kinds of share buffer.
Tracked-On: #8209
Signed-off-by: Conghui <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
sbuf is now only used for debug purpose, but later, it will be used as a
common interfaces. So, move the sbuf related code out of the debug directory.
Tracked-On: #8209
Signed-off-by: Conghui <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Improve SMP call to support ACRN shell to operate RTVM.
before, the RTVM CPU can't be kicked off by notification IPI,
so some shell commands can't support it, like rdmsr/wrmsr,
memory/registers dump. So INIT will be used for RTVM, which
LAPIC is pass-thru.
Tracked-On: #8207
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
By default, notification IPI used to kick sharing pCPU, INIT
used to kick partition pCPU. If USE_INIT_IPI flag is passed to
hypervisor, only INIT will be used to kick pCPU.
Tracked-On: #8207
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
INIT signal has been used to kick off the partitioned pCPU, like RTVM,
whose LAPIC is pass-through. notification IPI is used to kick off
sharing pCPU.
Add mode_to_kick_pcpu in per-cpu to control the way of kicking
pCPU.
Tracked-On: #8207
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The access to PCI config_space is handled in HV for Passthrough pci
devices. And it also provides one mechanism to forward cfg_access of
some registers to DM. For example: the opregion reg for GPU device.
This patch tried to add the support of emulated PCI ROM bar for the
device. And it doesn't handle the phys PCI ROM bar of phys PCI devices.
At the same time the rom firmware is provided in DM and pci rom bar_reg
is also emulated in DM, this leverages the quirk mechanism so that the
access to PCI rom bar_reg is forwarded to DM.
Tracked-On: #8175
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Acked-by: Wang Yu <yu1.wang@intel.com>
The design of ACRN CPU performance management is to let hardware
do the autonomous frequency selection(or set to a fixed value),
and remove guest's ability to control CPU frequency.
This patch is to remove guest's ability to control CPU frequency by
removing the guests' HWP/EIST CPUIDs and blocking the related MSR
accesses. Including:
- Remove CPUID.06H:EAX[7..11] (HWP)
- Remove CPUID.01H:ECX[7] (EIST)
- Inject #GP(0) upon accesses to MSR_IA32_PM_ENABLE,
MSR_IA32_HWP_CAPABILITIES, MSR_IA32_HWP_REQUEST,
MSR_IA32_HWP_STATUS, MSR_IA32_HWP_INTERRUPT,
MSR_IA32_HWP_REQUEST_PKG
- Emulate MSR_IA32_PERF_CTL. Value written to MSR_IA32_PERF_CTL
is just stored for reading. This is like how the native
environment would behavior when EIST is disabled from BIOS.
- Emulate MSR_IA32_PERF_STATUS by filling it with base frequency
state. This is consistent with Windows, which displays current
frequency as base frequency when running in VM.
- Hide the IA32_MISC_ENABLE bit 16 (EIST enable) from guests.
This bit is dependent to CPUID.01H:ECX[7] according to SDM.
- Remove CPID.06H:ECX[0] (hardware coordination feedback)
- Inject #GP(0) upon accesses to IA32_MPERF, IA32_APERF
Also DM do not need to generate _PSS/_PPC for post-launched VMs
anymore. This is done by letting hypercall HC_PM_GET_CPU_STATE sub
command ACRN_PMCMD_GET_PX_CNT and ACRN_PMCMD_GET_PX_DATA return (-1).
Tracked-On: #8168
Signed-off-by: Wu Zhou <wu.zhou@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
BVT schedule rule:
When a new thread is wakeup and added to runqueue, it will get the
smallest avt (svt) from runqueue to initiate its avt. If the svt is
smaller than it's avt, it will keep the original avt. With the svt, it
can prevent a thread from claiming an excessive share of CPU after
sleepting for a long time.
For the reboot issue, when the VM is reboot, it means a new vcpu thread
is wakeup, but at this time, the Service VM's vcpu thread is blocked,
and removed from the runqueue, and the runqueue is empty, so the svt is
0. The new vcpu thread will get avt=0. avt=0 means very high priority,
and can run for a very long time until it catch up with other thread's
avt in runqueue.
At this time, when Service VM's vcpu thread wakeup, it will check the
svt, but the svt is very small, so will not update it's avt according to
the rule, thus has a very low priority and cannot be scheduled.
To fix it, update svt in pick_next handler to make sure svt is align
with the avt of the first obj in runqueue.
Tracked-On: #7944
Signed-off-by: Conghui <conghui.chen@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
1. make memcpy_erms as a public API; add a new one
memcpy_erms_backwards, which supports to copy data from tail to head.
2. improve to use right/left/home/end key to move cursor, and support
delete/backspace key to modify current input command.
Tracked-On: #7931
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
For platform that supports RRSBA (Restricted Return Stack Buffer
Alternate), using retpoline may not be sufficient to guard against branch
history injection or intra-mode branch target injection. RRSBA must
be disabled to prevent CPUs from using alternate predictors for RETs.
Quoting Intel CVE-2022-0001/CVE-2022-0002:
Where software is using retpoline as a mitigation for BHI or intra-mode BTI,
and the processor both enumerates RRSBA and enumerates RRSBA_DIS controls,
it should disable this behavior.
...
Software using retpoline as a mitigation for BHI or intra-mode BTI should use
these new indirect predictor controls to disable alternate predictors for RETs.
See: https://www.intel.com/content/www/us/en/developer/articles/technical/
software-security-guidance/technical-documentation/branch-history-injection.html
Tracked-On: #7907
Signed-off-by: Yifan Liu <yifan1.liu@intel.com>
TLFS defined 2 vMSRs which can be used by Windows guest to get the
TSC/APIC frequencies from hypervisor. This patch adds the support
of HV_X64_MSR_TSC_FREQUENCY/HV_X64_MSR_APIC_FREQUENCY vMSRS whose
availability is exposed by CPUID.0x40000003:EAX[bit11] and EDX[bit8].
v1->v2:
- revise commit message to highlight that the changes are for WaaG
Tracked-On: #7876
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
On some platforms CPUID.0x15:ECX is zero and CPUID.0x16 can
only return the TSC frequency in MHZ which is not accurate.
For example the TSC frequency obtained by CPUID.0x16 is 2300
MHZ and the TSC frequency calibrated by HPET is 2303.998 MHZ
which is much closer to the actual TSC frequency 2304.000 MHZ.
This patch adds the support of using HPET to calibrate TSC
when HPET is available and CPUID.0x15:ECX is zero.
v3->v4:
- move calc_tsc_by_hpet into hpet_calibrate_tsc
v2->v3:
- remove the NULL check in hpet_init
- remove ""& 0xFFFFFFFFU" in tsc_read_hpet
- add comment for the counter wrap in the low 32 bits in
calc_tsc_by_hpet
- use a dedicated function for hpet_calibrate_tsc
v1->v2:
- change native_calibrate_tsc_cpuid_0x15/0x16 to
native_calculate_tsc_cpuid_0x15/0x16
- move hpet_init to BSP init
- encapsulate both HPET and PIT calibration to one function
- revise the commit message with an example"
Tracked-On: #7876
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Modified the copyright year range in code, and corrected "int32_tel"
into "Intel" in two "hypervisor/include/debug/profiling.h" and
"hypervisor/include/debug/profiling_internal.h".
Tracked-On: #7559
Signed-off-by: Ziheng Li <ziheng.li@intel.com>
As mentioned in previous patch, wbinvd utilizes the vcpu_make_request
and signal_event call pair to stall other vcpus. Due to the fact that
these two calls are not thread-safe, we need to avoid concurrent call to
this API pair.
This patch adds wbinvd lock to serialize wbinvd emulation.
Tracked-On: #7887
Signed-off-by: Yifan Liu <yifan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Commit d575edf79a changes the internal
implementation of wait_event and signal_event to use a counter instead
of a boolean value.
The background was:
ACRN utilizes vcpu_make_request and signal_event pair to shoot down
other vcpus and let them wait for signals. vcpu_make_request eventually
leads to target vcpu calling wait_event.
However vcpu_make_request/signal_event pair was not thread-safe,
and concurrent calls of this pair of API could lead to problems.
One such example is the concurrent wbinvd emulation, where vcpus may
concurrently issue vcpu_make_request/signal_event to synchronize wbinvd
emulation.
d575edf commit uses a counter in internal implementation of
wait_event/signal_event to avoid data races.
However by using a counter, the wait/signal pair now carries semantics of
semaphores instead of events. Semaphores require caller to carefully
plan their calls instead of multiply signaling any number of times to the same
event, which deviates from the original "event" semantics.
This patch changes the API implementation back to boolean-based, and
re-resolve the issue of concurrent wbinvd in next patch.
This also partially reverts commit 10963b04d1,
which was introduced because of the d575edf.
Tracked-On: #7887
Signed-off-by: Yifan Liu <yifan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There is an issue of calculate 2^n roundup of CONFIG_MAX_PT_IRQ_ENTRIES,
and the code style is very ugly when we use macro to fix it.
So this patch move MAX_IR_ENTRIES to offline tool which could do align
check and calculate it automatically.
Signed-off-by: Chenli Wei <chenli.wei@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Current code limit the MAX vUART number to 8 which is not enough for
Service VM which should config S5 UART for each user VM.
We could count how many vUARTs we need by offline tool, so remove the
define of MAX_VUART_NUM_PER_VM to offline tool is a simple and accurate
way to allocate vUARTs.
Tracked-On: #8782
Signed-off-by: Chenli Wei <chenli.wei@intel.com>
