The patch re-arch boot component header files by:
- moving multiboot.h from include/arch/x86/ to boot/include/ and keep
this header for multiboot1 protocol data struct only;
- moving multiboot related MACROs in cpu_primary.S to multiboot.h;
- creating an independent boot.h to store acrn specific boot information
for other files' reference;
Tracked-On: #4419
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
BVT (Borrowed virtual time) scheduler is used to schedule vCPUs on pCPU.
It has the concept of virtual time, vCPU with earliset virtual time is
dispatched first.
Main concepts:
tick timer:
a period tick is used to measure the physcial time in units of MCU
(minimum charing unit).
runqueue:
thread in the runqueue is ordered by virtual time.
weight:
each thread receives a share of the pCPU in proportion to its
weight.
context switch allowance:
the physcial time by which the current thread is allowed to advance
beyond the next runnable thread.
warp:
a thread with warp enabled will have a change to minus a value (Wi)
from virtual time to achieve higher priority.
virtual time:
AVT: actual virtual time, advance in proportional to weight.
EVT: effective virtual time.
EVT <- AVT - ( warp ? Wi : 0 )
SVT: scheduler virtual time, the minimum AVT in the runqueue.
Tracked-On: #4410
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1. Rename BOOT_CPU_ID to BSP_CPU_ID
2. Repace hardcoded value with BSP_CPU_ID when
ID of BSP is referenced.
Tracked-On: #4420
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Now we split passthrough PCI device from DM to HV, we could remove all the passthrough
PCI device unused code.
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
To enable gvt-d,need to allow the GPU IOMMU.
While gvt-d hasn't been enabled on APL yet,
so let APL disable GPU IOMMU.
v2 -> v3:
* let APL platforms disable GPU IOMMU.
Tracked-On: #4405
Signed-off-by: Junming Liu <junming.liu@intel.com>
Reviewed-by: Wu Binbin <binbin.wu@intel.com>
In platforms that support CAT, when it is enabled by ACRN, i.e.
IA32_resourceType_MASK_n registers are programmed with customized values,
it has impacts to the whole system.
The per guest flag GUEST_FLAG_CLOS_REQUIRED suggests that CAT may be
enabled in some guests, but not in others who don't have this flag,
which is conceptually incorrect.
This patch removes GUEST_FLAG_CLOS_REQUIRED, and adds a new Kconfig
entry CAT_ENABLED for CAT enabling. When it's enabled, platform_clos_array[]
defines a set of system-wide Class of Service (COS, or CLOS), and the
per guest vm_configs[].clos associates the guest with particular CLOS.
Tracked-On: #2462
Signed-off-by: Zide Chen <zide.chen@intel.com>
1. Align the coding style for these MACROs
2. Align the values of fixed VECTORs
Tracked-On: #4348
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
is_polling_ioreq is more straightforward. Rename it.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Sometimes HV wants to know if there are pending interrupts of one vcpu.
Add .has_pending_intr interface in acrn_apicv_ops and return the pending
interrupts status by check IRRs of apicv.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Introduce two kinds of events for each vcpu,
VCPU_EVENT_IOREQ: for vcpu waiting for IO request completion
VCPU_EVENT_VIRTUAL_INTERRUPT: for vcpu waiting for virtual interrupts events
vcpu can wait for such events, and resume to run when the
event get signalled.
This patch also change IO request waiting/notifying to this way.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Since we restore BAR values when writing Command Register if necessary. We don't
need to trap FLR and do the BAR restore then.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Per SDM 10.12.5.1 vol.3, local APIC should keep LAPIC state after receiving
INIT. The local APIC ID register should also be preserved.
Tracked-On: #4267
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The patch abstract a vcpu_reset_internal() api for internal usage, the
function would not touch any vcpu state transition and just do vcpu reset
processing. It will be called by create_vcpu() and reset_vcpu().
The reset_vcpu() will act as a public api and should be called
only when vcpu receive INIT or vm reset/resume from S3. It should not be
called when do shutdown_vm() or hcall_sos_offline_cpu(), so the patch remove
reset_vcpu() in shutdown_vm() and hcall_sos_offline_cpu().
The patch also introduced reset_mode enum so that vcpu and vlapic could do
different context operation according to different reset mode;
Tracked-On: #4267
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Some MACROs in lapic.h are duplicated with apicreg.h, and some MACROs are
never referenced, remove them.
Tracked-On: #4268
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add severity definitions for different scenarios. The static
guest severity is defined according to guest configurations.
Also add sanity check to make sure the severity for all guests
are correct.
Tracked-On: #4270
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
For system S5, ACRN had assumption that SOS shutdown will trigger
system shutdown. So the system shutdown logical is:
1. Trap SOS shutdown
2. Wait for all other guest shutdown
3. Shutdown system
The new logical is refined as:
If all guest is shutdown, shutdown whole system
Tracked-On: #4270
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
ACRN hypervisor should trap guest doing PCIe FLR. Besides, it should save some status
before doing the FLR and restore them later, only BARs values for now.
This patch will trap guest Device Capabilities Register write operation if the device
supports PCI Express Capability and check whether it wants to do device FLR. If it does,
call pdev_do_flr to do the job.
Tracked-On: #3465
Signed-off-by: Li Fei1 <fei1.li@intel.com>
We don't use INIT signal notification method now. This patch
removes them.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
There is a window where we may miss the current request in the
notification period when the work flow is as the following:
CPUx + + CPUr
| |
| +--+
| | | Handle pending req
| <--+
+--+ |
| | Set req flag |
<--+ |
+------------------>---+
| Send NMI | | Handle NMI
| <--+
| |
| |
| +--> vCPU enter
| |
+ +
So, this patch enables the NMI-window exiting to trigger the next vmexit
once there is no "virtual-NMI blocking" after vCPU enter into VMX non-root
mode. Then we can process the pending request on time.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
The NMI for notification should not be inject to guest. So,
this patch drops NMI injection request when we use NMI
to notify vCPUs. Meanwhile, ACRN doesn't support vNMI well
and there is no well-designed way to check if the NMI is
for notification or for guest now. So, we take all the NMIs as
notificaton NMI for hard rtvm temporarily. It means that the
hard rtvm will never receive NMI with this patch applied.
TODO: vNMI support is not ready yet. we will add it later.
Tracked-On: #3886
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
Reserved bits in a 8-bit PAT field has been checked in pat_mem_type_invalid.
Remove this redundant check "(PAT_FIELD_RSV_BITS & field) != 0UL" in
write_pat_msr.
Tracked-On: #1842
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
This patch adds a helper function send_single_nmi. The fisrt caller
will soon come with the following patch.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
This patch installs a NMI handler in acrn IDT to handle
NMIs out of dispatch_exception.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
In current architecutre, the maximum vCPUs number per VM could not
exceed the pCPUs number. Given the MAX_PCPU_NUM macro is provided
in board configurations, so remove the MAX_VCPUS_PER_VM from Kconfig
and add a macro of MAX_VCPUS_PER_VM to reference MAX_PCPU_NUM directly.
Tracked-On: #4230
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
rename the macro since MAX_PCPU_NUM could be parsed from board file and
it is not a configurable item anymore.
Tracked-On: #4230
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
remove 'guest_init_pml4' and 'tmp_pg_array' in vm_arch
since they are not used.
Tracked-On: #1842
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
IO sensitive Round-robin scheduler aim to schedule threads with
round-robin policy. Meanwhile, we also enhance it with some fairness
configuration, such as thread will be scheduled out without properly
timeslice. IO request on thread will be handled in high priority.
This patch only add a skeleton for the sched_iorr scheduler.
Tracked-On: #4178
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Signed-off-by: Yu Wang <yu1.wang@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
On some platforms, HPA regions for Virtual Machine can not be
contiguous because of E820 reserved type or PCI hole. In such
cases, pre-launched VMs need to be assigned non-contiguous memory
regions and this patch addresses it.
To keep things simple, current design has the following assumptions,
1. HPA2 always will be placed after HPA1
2. HPA1 and HPA2 don’t share a single ve820 entry.
(Create multiple entries if needed but not shared)
3. Only support 2 non-contiguous HPA regions (can extend
at a later point for multiple non-contiguous HPA)
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Tracked-On: #4195
Acked-by: Anthony Xu <anthony.xu@intel.com>
With cpu-sharing enabled, there are more than 1 vcpu on 1 pcpu, so the
smp_call handler should switch the vmcs to the target vcpu's vmcs. Then
get the info.
dump_vcpu_reg and dump_guest_mem should run on certain vmcs, otherwise,
there will be #GP error.
Renaming:
vcpu_dumpreg -> dump_vcpu_reg
switch_vmcs -> load_vmcs
Tracked-On: #4178
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Deterministic is important for RTVM. The mitigation for MCE on
Page Size Change converts a large page to 4KB pages runtimely during
the vmexit triggered by the instruction fetch in the large page.
These vmexits increase nondeterminacy, which should be avoided for RTVM.
This patch builds 4KB page mapping in EPT for RTVM to avoid these vmexits.
Tracked-On: #4101
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Only apply the software workaround on the models that might be
affected by MCE on page size change. For these models that are
known immune to the issue, the mitigation is turned off.
Atom processors are not afftected by the issue.
Also check the CPUID & MSR to check whether the model is immune to the issue:
CPU is not vulnerable when both CPUID.(EAX=07H,ECX=0H).EDX[29] and
IA32_ARCH_CAPABILITIES[IF_PSCHANGE_MC_NO] are 1.
Other cases not listed above, CPU may be vulnerable.
This patch also changes MACROs for MSR IA32_ARCH_CAPABILITIES bits to UL instead of U
since the MSR is 64bit.
Tracked-On: #4101
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
After changing init_vmcs to smp call approach and do it before
launch_vcpu, it could work with noop scheduler. On real sharing
scheudler, it has problem.
pcpu0 pcpu1 pcpu1
vmBvcpu0 vmAvcpu1 vmBvcpu1
vmentry
init_vmcs(vmBvcpu1) vmexit->do_init_vmcs
corrupt current vmcs
vmentry fail
launch_vcpu(vmBvcpu1)
This patch mark a event flag when request vmcs init for specific vcpu. When
it is running and checking pending events, will do init_vmcs firstly.
Tracked-On: #4178
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
xsave area:
legacy region: 512 bytes
xsave header: 64 bytes
extended region: < 3k bytes
So, pre-allocate 4k area for xsave. Use certain instruction to save or
restore the area according to hardware xsave feature set.
Tracked-On: #4166
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Anthony Xu <anthony.xu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
ptirq_msix_remap doesn't do the real remap, that's the vmsi_remap and vmsix_remap_entry
does. ptirq_msix_remap only did the preparation.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
We add new member pci_pdev.drhd_idx associating the DRHD
(IOMMU) with this pdev, and a method to convert a pbdf of a device to
this index by searching the pdev list.
Partial patch: drhd_index initialization handled in subsequent patch.
Tracked-On: #4134
Signed-off-by: Alexander Merritt <alex.merritt@intel.com>
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
add shell command to support dump dump guest memory
e.g.
dump_guest_mem vm_id, gva, length
Tracked-On: #4144
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In 64-bit mode, processor pushes SS and RSP onto stack unconditionally.
Also when dumping the exception info, it makes more sense to dump
the RSP at the point of interrupt, rather than the RSP after pushing
context (including GPRs)
Tracked-On: #4102
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Issue description:
-----------------
Machine Check Error on Page Size Change
Instruction fetch may cause machine check error if page size
and memory type was changed without invalidation on some
processors[1][2]. Malicious guest kernel could trigger this issue.
This issue applies to both primary page table and extended page
tables (EPT), however the primary page table is controlled by
hypervisor only. This patch mitigates the situation in EPT.
Mitigation details:
------------------
Implement non-execute huge pages in EPT.
This patch series clears the execute permission (bit 2) in the
EPT entries for large pages. When EPT violation is triggered by
guest instruction fetch, hypervisor converts the large page to
smaller 4 KB pages and restore the execute permission, and then
re-execute the guest instruction.
The current patch turns on the mitigation by default.
The follow-up patches will conditionally turn on/off the feature
per processor model.
[1] Refer to erratum KBL002 in "7th Generation Intel Processor
Family and 8th Generation Intel Processor Family for U Quad Core
Platforms Specification Update"
https://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/7th-gen-core-family-spec-update.pdf
[2] Refer to erratum SKL002 in "6th Generation Intel Processor
Family Specification Update"
https://www.intel.com/content/www/us/en/products/docs/processors/core/desktop-6th-gen-core-family-spec-update.html
Tracked-On: #4101
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
MISRA C requires specified bounds for arrays declaration, previous declaration
of platform_clos_array in board.h does not meet the requirement.
Tracked-On: #3987
Signed-off-by: Victor Sun <victor.sun@intel.com>
The DMAR info is board specific so move the structure definition to board.c.
As a configruation file, the whole board.c could be generated by acrn-config
tool for each board.
Please note we only provide DMAR info MACROs for nuc7i7dnb board. For other
boards, ACPI_PARSE_ENABLED must be set to y in Kconfig to let hypervisor parse
DMAR info, or use acrn-config tool to generate DMAR info MACROs if user won't
enable ACPI parse code for FuSa consideration.
The patch also moves the function of get_dmar_info() to vtd.c, so dmar_info.c
could be removed.
Tracked-On: #3977
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The value of CONFIG_MAX_IOMMU and MAX_DRHDS are identical to DRHD_COUNT
which defined in platform ACPI table, so remove CONFIG_MAX_IOMMU_NUM
from Kconfig and link these three MACROs together.
Tracked-On: #3977
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Now the e820 structure store ACRN HV memory layout, not the physical memory layout.
Rename e820 to hv_hv_e820 to show this explicitly.
Tracked-On: #4007
Signed-off-by: Li Fei1 <fei1.li@intel.com>
After adding PCI BAR remap support, mmio_node may unregister when there's others
access it. This patch add a lock to protect mmio_node access.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Since guest could re-program PCI device MSI-X table BAR, we should add mmio
emulation handler unregister.
However, after add unregister_mmio_emulation_handler API, emul_mmio_regions
is no longer accurate. Just replace it with max_emul_mmio_regions which records
the max index of the emul_mmio_node.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
In theory, guest could re-program PCI BAR address to any address. However, ACRN
hypervisor only support [0, top_address_space) EPT memory mapping. So we need to
check whether the PCI BAR re-program address is within this scope.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
kick means to notify one thread_object. If the target thread object is
running, send a IPI to notify it; if the target thread object is
runnable, make reschedule on it.
Also add kick_vcpu API in vcpu layer to notify vcpu.
Tracked-On: #3813
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Signed-off-by: Yu Wang <yu1.wang@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
