In write_trampoline_stack_sym(), when do relocation for pcpu's stack,
it wrongly adds an offset. As a result, during booting, when non-BSP
CPU (APs) tries to run trampoline code once they are waken up by BSP
via SIPI, system hangs.
Tracked-On: #2349
Signed-off-by: Chaohong guo <chaohong.guo@intel.com>
Reviewed-By: Yin Fengwei <fengwei.yin@intel.com>
Reviewed-by: Zide Chen <zide.chen@intel.com>
when relocation is enabled, the calcuation of HV size in init_paging
routine is not right. As a result, it doesn't enable NX bit for many
pages which don't belong to hypervisor text section.
Tracked-On: #2349
Signed-off-by: Chaohong guo <chaohong.guo@intel.com>
Reviewed-by: Zide Chen <zide.chen@intel.com>
In init_paging(), when modify page table, it does a round up to 2M on
the starting address of HV memory. If the address is not 2M aligned,
memory overwrite occurs, or memory attribute(cache, u/s) may be not
right. Besides, trusty memory (uos_sworld_memory) in .bss section is 2M
aligned during compiling, after enabling HV memroy 2M alignment, when
relocation is enabled, EFI stub or other loaders just needs to find a
2M-aligned starting addr for HV memory.
Tracked-On: #2349
Signed-off-by: Chaohong guo <chaohong.guo@intel.com>
Reviewed-by: Zide Chen <zide.chen@intel.com>
efi_ctx is passed by EFI stub to hypervisor. The memory was allocated
right after HV binary and marked as Efireserved. But HV is doing a 2MB
alignment in init_paging() and might overwrite the efi_ctx struct or
change the page table attribute. Now, EFI STUB uses Efiloaderdata type
memory and the memory can be re-use by hypervisor/sos after boot time
done. HV should save itself a copy if the content is still needed after
init_paging().
Tracked-On: #2349
Signed-off-by: Chaohong guo <chaohong.guo@intel.com>
Reviewed-by: Zheng, Gen <gen.zheng@intel.com>
-- fix "Macro parameter not in brackets" for PLUG_CPU(n)
-- fix "Array has no bounds specified" for vm_configs[]
Tracked-On: #861
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
This is the following patch after removing pending_pre_work, it make sure
all io emulation is done on its own cpu.
For hv emulated request, it follows the steps:
hv_emulate_pio->emulate_pio_complete
hv_emulate_mmio->emulate_mmio_complete
For dm emulated request, it follows the steps:
acrn_insert_request->dm_emulate_io_complete
while in acrn_insert_request, it could trigger scheduling out then resume by
hcall_notify_ioreq_finish, or busy wait for ioreq completion if polling mode
is enabled.
Tracked-On: #2394
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Xu, Anthony <anthony.xu@intel.com>
Now we do not need pending_pre_work anymore, as we can make sure IO request
VCPU resume from where it paused.
Now only three fixed points will try to do schedule:
- vcpu_thread: before vm entry, will check reschedule flag and to it if needed
- default_idle: loop check reschedule flag to see if need switch out
- io request: if IO REQ need DM's handle, it will schedule out
Tracked-On: #2394
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Xu, Anthony <anthony.xu@intel.com>
this patch added full context switch support for scheduling, it make sure
each VCPU has its own stack, and added host_sp field in struct sched_object
to record host stack pointer for each switch out object.
Arch related function arch_switch_to is added for context switch.
To benefit debugging, a name[] field is also added into struct sched_object.
Tracked-On: #2394
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Xu, Anthony <anthony.xu@intel.com>
To support full context switch scheduling, each physical
CPU must have its own idle sched_obj.
Tracked-On: #2394
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Xu, Anthony <anthony.xu@intel.com>
This patch adds the dependency of $(LIB_FLAGS) when building .out file.
So that the target is updated whenever there is a update in
debug/release library.
Tracked-On: #2389
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
For binutils <= 2.26:
'U' suffix for unsigned constant is not accepted by binutils assembler.
This patch separates the MACRO definition for ASSEMBLER
and non-ASSEMBLER code in idt.h
Tracked-On: #2200
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
separate the private macro/structure/functions, which are just used
in instr_emul.c;
and move instr_emul.h to public include path.
Tracked-On: #1842
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
The member of lapic_pt in acrn_vm_config will be replaced by
guest_flag of LAPIC_PASSTHROUGH;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The member of bootargs in acrn_vm_config will be replaced by
acrn_vm_os_config struct.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The member of mem_size and start_hpa in acrn_vm_config struct will
be replaced with the acrn_vm_mem_config struct;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
For each vm_array[] item, its config is located in corresponding
index of vm_configs[], so vm_config pointer is not needed any more.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
All the legacy cpu configration in vm_description.c are all cleaned up;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The VM number configuration in description.c is never used, remove it;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
We will use guest_flags of SECURE_WORLD_ENABLED to check wthether
sworld is supported.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch creates a new get_sos_vm() api to replace get_vm_from_vmid(0U)
because VM 0 might not be SOS VM now;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The patch will show correct VM name per its configuration. As we do not
validate vm id when call get_vm_from_vmid() any more, we only show VM's
states which their VM type are defined;
If VM name is not configured in config file, then the name is specified
with vm id, i.e. "ACRN VM_(vm id)"
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When pcpu enter guest mode, it will call launch_vms() function to launch
VMs in global vm_configs array.
In launch_vms() function, current pcpu will go through vm_config array list
and check whether it is a bsp of configured VM, if yes then it will prepare
corresponding VM and start it. The index of vm_config array will be specified
to VM id.
The first least significant bit in pcpu_bitmap means the bsp of the VM.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Under sharing mode, VM0 is identical with SOS VM. But the coupling of
SOS VM and VM 0 is not friendly for partition mode.
This patch is a pure term change of vm0 to sos VM, it does not change
any code logic or senmantic.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
move this api from ept.c to io_emul.c to avoid
reverse dependency.
Tracked-On: #1842
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
move this api from io_emul.c to vm.c to avoid reverse
dependency
Tracked-On: #1842
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
to edge interrupt, like eth device, it can triger the interrupt again
when its IRQ in softirq entry queue or in timer list.
in current design, for sofrirq entry, it calls "list_del" before
"list_add_tail", to avoid the entry added twice.
so for interrupt delay timer, add to check if it is started
then just drop the next one; to avoid it enqueue twice.
Tracked-On: #2365
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Reviewed-by: Li, Fei1 <fei1.li@intel.com>
mptable pointer in acrn_vm_config struct and also extern struct mptable_vm1/2
declared in mptable.h are not used any more, remove them.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
- add new struct member for acrn_vm_config;
- add sharing_config.c file with initialized vm_config array;
- add SOS VM config header for apl-mrb/apl-nuc/up2 and dnv-cb2 board;
- and partition_config.c file with dummy vm_config array;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch is a pure term change of vm_description to vm_config,
the struct name of vm_description is changed to acrn_vm_config.
The patch does not change any code logic or senmantic.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Currently, we support SBL on two different boards.
So build and install them all in E2E build.
Tracked-On: #2344
Signed-off-by: Tw <wei.tan@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
Currently the SOS kernel will call hcall_set_callback_vector to config
the expected up-notification vector(0xF3) and then hypervisor uses the
passed vector to raise the interrupt to SOS when needed.
As sos kernel already switches to 0xF3 notification vector, the default
notification vector can be changed from 0xF7 to 0xF3. In such case it still
can work well even when the SOS kernel doesn't reconfigure the notification
vector.
Tracked-On: projectacrn/acrn-hypervisor#2355
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
1. move the CR related code from vmcs/vcpu to vCR source files.
2. also add virtual_cr.h to acrn.doxyfile to avoid doc failure.
Tracked-On: #1842
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
-- Change acrn_vhm_vector to static, only used in io_request.c
-- Add set_vhm_vector() api, it will call this api instead of
acrn_vhm_vector except io_request.c
Tracked-On: #1842
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Anthony Xu <anthony.xu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
- add definitions of all architectural MSRs
- add definitions of majority of non architectural MSRs
The non-architectural MSR definitions are specific to particular CPU model
or family.
e.g. MSR 0xE01 could refer to different MSRs in difference processors, and
in this patch, MSR_R0_PMON_BOX_STATUS is chosen without any particular reasons.
MSR_R0_PMON_BOX_STATUS in Xeon Processor 7500 Series
MSR_C0_PMON_EVNTSEL0 in Xeon E5 V3 family
MSR_UNC_PERF_GLOBAL_CTRL in 6th plus generations Core Processors
Tracked-On: #1867
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Split decode_prefixes() to 2 small APIs
v1-->v2:
split decode_prefixes to 2 APIs
Tracked-On: #861
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The MISRA-C Standards suggests procedures to be single exit
Tracked-On: #861
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Because ACRN_REQUEST_TMR_UPDATE is not needed anymore, this commit remove
the MACRO definition and its related logic, including following functions:
- apicv_batch_set_tmr()
- vlapic_apicv_batch_set_tmr()
- vlapic_set_tmr_one_vec()
- vioapic_update_tmr()
Tracked-On: #2343
Signed-off-by: Yan, Like <like.yan@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This commit changes the EOI_EXIT_BITMAP as follows:
- add a eoi_exit_bitmap to vlapic structure;
- go through all the RTEs and set eoi_exit_bitmap in the vlapic structure when related RTE fields are modified;
- add ACRN_REQUEST_EOI_EXIT_UPDATE, if eoi_exit_bitmap changed, request the corresponding vcpu to write the bitmap
to VMCS.
Tracked-On: #2343
Signed-off-by: Yan, Like <like.yan@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Current ACRN implementation update TMR bits one time only when related RTE fields changed,
which is not acting like actual hardware.
From SDM vol3 10.8.4:
"Upon acceptance of an interrupt into the IRR, the corresponding TMR bit is cleared for
edge-triggered interrupts and set for leveltriggered interrupts."
This commit change the ACRN implementation to set/clear corresponding TMR bit when inject
intr to vlapic.
Tracked-On: #2343
Signed-off-by: Yan, Like <like.yan@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
On platforms that put ACPI RSDT in "Reserved" type memory, ACRN
fails to parse RSDP and therefore ACPI Tables. This patch adds
"Reserved" memory regions in E820 as Supervisor pages.
Tracked-On: #2320
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Refer to sha256 description to rename function name
Tracked-On: #861
Signed-off-by: Chen Gang G <gang.g.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When we use script to analyze the latency between vm_exit and vm_entry,
it does not include the duration of vm_exit handler.
The patch moves the vm_exit trace before vmexit_handler.
v2: move vm_exit trace right after run_vcpu.
Tracked-On: #2341
Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed-by: Yan, Like <like.yan@intel.com>
The struct vm_lu_mem_map is not used by code. Remove it.
Also, add bracks () for the variables in macro foreach_vcpu.
Tracked-On: #861
Signed-off-by: Chaohong guo <chaohong.guo@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
to meeting MISRA, add more bracks for if conditions; also a small
change to copy_gpa() to fix DD flow complaint from MISRA
Tracked-On: #861
Signed-off-by: Chaohong guo <chaohong.guo@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
