As ACRN prepares to support servers with large amounts of memory
current logic to allocate space for 4K pages of EPT at compile time
will increase the size of .bss section of ACRN binary.
Bootloaders could run into a situation where they cannot
find enough contiguous space to load ACRN binary under 4GB,
which is typically heavily fragmented with E820 types Reserved,
ACPI data, 32-bit PCI hole etc.
This patch does the following
1) Works only for "direct" mode of vboot
2) reserves space for 4K pages of EPT, after boot by parsing
platform E820 table, for all types of VMs.
Size comparison:
w/o patch
Size of DRAM Size of .bss
48 GB 0xe1bbc98 (~226 MB)
128 GB 0x222abc98 (~548 MB)
w/ patch
Size of DRAM Size of .bss
48 GB 0x1991c98 (~26 MB)
128 GB 0x1a81c98 (~28 MB)
Tracked-On: #4563
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There're some cases the SOS (higher severity guest) needs to access the
post-launched VM (lower severity guest) PCI CFG space:
1. The SR-IOV PF needs to reset the VF
2. Some pass through device still need DM to handle some quirk.
In the case a device is assigned to a UOS and is not in a zombie state, the SOS
is able to access, if and only if the SOS has higher severity than the UOS.
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Currently ept_pages_info[] is initialized with first element only that force
VM of id 0 using SOS EPT pages. This is incorrect for logical partition and
hybrid scenario. Considering SOS_RAM_SIZE and UOS_RAM_SIZE are configured
separately, we should use different ept pages accordingly.
So, the PRE_VM_NUM/SOS_VM_NUM and MAX_POST_VM_NUM macros are introduced to
resolve this issue. The macros would be generated by acrn-config tool when
user configure ACRN for their specific scenario.
One more thing, that when UOS_RAM_SIZE is less then 2GB, the EPT address
range should be (4G + PLATFORM_HI_MMIO_SIZE).
Tracked-On: #4458
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The patch re-arch boot component header files by:
- moving multiboot.h from include/arch/x86/ to boot/include/ and keep
this header for multiboot1 protocol data struct only;
- moving multiboot related MACROs in cpu_primary.S to multiboot.h;
- creating an independent boot.h to store acrn specific boot information
for other files' reference;
Tracked-On: #4419
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In platforms that support CAT, when it is enabled by ACRN, i.e.
IA32_resourceType_MASK_n registers are programmed with customized values,
it has impacts to the whole system.
The per guest flag GUEST_FLAG_CLOS_REQUIRED suggests that CAT may be
enabled in some guests, but not in others who don't have this flag,
which is conceptually incorrect.
This patch removes GUEST_FLAG_CLOS_REQUIRED, and adds a new Kconfig
entry CAT_ENABLED for CAT enabling. When it's enabled, platform_clos_array[]
defines a set of system-wide Class of Service (COS, or CLOS), and the
per guest vm_configs[].clos associates the guest with particular CLOS.
Tracked-On: #2462
Signed-off-by: Zide Chen <zide.chen@intel.com>
Add severity definitions for different scenarios. The static
guest severity is defined according to guest configurations.
Also add sanity check to make sure the severity for all guests
are correct.
Tracked-On: #4270
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
In current architecutre, the maximum vCPUs number per VM could not
exceed the pCPUs number. Given the MAX_PCPU_NUM macro is provided
in board configurations, so remove the MAX_VCPUS_PER_VM from Kconfig
and add a macro of MAX_VCPUS_PER_VM to reference MAX_PCPU_NUM directly.
Tracked-On: #4230
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
On some platforms, HPA regions for Virtual Machine can not be
contiguous because of E820 reserved type or PCI hole. In such
cases, pre-launched VMs need to be assigned non-contiguous memory
regions and this patch addresses it.
To keep things simple, current design has the following assumptions,
1. HPA2 always will be placed after HPA1
2. HPA1 and HPA2 don’t share a single ve820 entry.
(Create multiple entries if needed but not shared)
3. Only support 2 non-contiguous HPA regions (can extend
at a later point for multiple non-contiguous HPA)
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Tracked-On: #4195
Acked-by: Anthony Xu <anthony.xu@intel.com>
--remove unnecessary includes
--remove unnecssary forward-declaration for 'struct vhm_request'
Tracked-On: #861
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Add this vcpu_affinity[] for each VM to indicate the assignment policy.
With it, pcpu_bitmap is not needed, so remove it from vm_config.
Instead, vcpu_affinity is a must for each VM.
This patch also add some sanitize check of vcpu_affinity[]. Here are
some rules:
1) only one bit can be set for each vcpu_affinity of vcpu.
2) two vcpus in same VM cannot be set with same vcpu_affinity.
3) vcpu_affinity cannot be set to the pcpu which used by pre-launched VM.
v4: config SDC with CONFIG_MAX_KATA_VM_NUM
v5: config SDC with CONFIG_MAX_PCPU_NUM
Tracked-On: #3663
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Signed-off-by: Yu Wang <yu1.wang@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
There is plan that define each VM configuration statically in HV and let
DM just do VM creating and destroying. So DM need get vcpu_num
information when VM creating.
This patch return the vcpu_num via the API param. And also initial the
VMs' cpu_num for existing scenarios.
Tracked-On: #3663
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Signed-off-by: Yu Wang <yu1.wang@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Now that ACPI is enabled for pre-launched VMs, we can remove all mptable code.
Tracked-On: #3601
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Statically define the per vm RSDP/XSDT/MADT ACPI template tables in vacpi.c,
RSDP/XSDT tables are copied to guest physical memory after checksum is
calculated. For MADT table, first fix up process id/lapic id in its lapic
subtable, then the MADT table's checksum is calculated before it is copies to
guest physical memory.
Add 8-bit checksum function in util.h
Tracked-On: #3601
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Add a field (vdev_ops) in struct acrn_vm_pci_dev_config to configure a PCI CFG
operation for an emulated PCI device. Use pci_pt_dev_ops for PCI_DEV_TYPE_PTDEV
by default if there's no such configure.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Align SOS pci device configure with pre-launched VM and filter pre-launched VM's
PCI PT device from SOS pci device configure.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
pci_dev_config in VM configure stores all the PCI devices for a VM. Besides PT
devices, there're other type devices, like virtual host bridge. So rename ptdev
to pci_dev for these configure.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Define/Use variable in place of code to improve readability:
Define new local variable struct pci_bar *vbar, and use vbar-> in place of vdev->bar[idx].
Define new local variable uint64_t vbar_base in init_vdev_pt
Rename uint64_t vbar[PCI_BAR_COUNT] of struct acrn_vm_pci_ptdev_config to uint64_t vbar_base[PCI_BAR_COUNT]
Tracked-On: #3241
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The vcpu num could be calculated based on pcpu_bitmap when prepare_vcpu()
is done, so remove this redundant configuration item;
Tracked-On: #3214
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Zephyr kernel is stripped ram image, its entry and load address
are explicitly defined in vm configurations, hypervisor will load
Zephyr directly based on these configurations.
Currently we only support boot Zephyr from protected mode.
Tracked-On: #3214
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Previously multiboot mods[0] is designed for kernel module for all
pre-launched VMs including SOS VM, and mods[0].mm_string is used
to store kernel cmdline. This design could not satisfy the requirement
of hybrid mode scenarios that each VM might use their own kernel image
also ramdisk image. To resolve this problem, we will use a tag in
mods mm_string field to specify the module type. If the tag could
be matched with os_config of VM configurations, the corresponding
module would be loaded;
Tracked-On: #3214
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Different kernel has different load method, it should be configurable
in vm configurations;
Tracked-On: #3214
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Add EPC information in vm configuration structure.
EPC information contains the EPC base and size allocated to a VM.
Tracked-On: #3179
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
VM Name length is restricted to 32 characters. kata creates
a VM name with GUID added as a part of VM name making it around
80 characters. So increasing this size to 128.
v1->v2:
It turns out that MAX_VM_OS_NAME_LEN usage in DM and HV are for
different use cases. So removing the macro from acrn_common.h.
Definied macro MAX_VMNAME_LEN for DM purposes in dm.h. Retaining
original macron name MAX_VM_OS_NAME_LEN for HV purposes but defined
in vm_config.h.
Tracked-On: #3138
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Define a static mptable array and each VM could index its vmptable by
vm id, then mptable is not needed in vm configurations;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
For pre-launched VMs, currently we set all vbars to 0s initially in
bar emulation code, guest OS will reprogram the bars when it sees the bars are uninited (0s).
We consider this is not the right solution, change to populate the
vbars (to non zero valid pci hole address) based on the vbar base
addresses predefined in vm_config.
Store a pointer to acrn_vm_pci_ptdev_config in struct pci_vdev
Tracked-On: #3022
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Rename structure acrn_vm_type to acrn_vm_load_order as it is used to
indicate the load order instead of the VM type.
Tracked-On: #2291
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The name NORMAL_VM does not clearly reflect the attribute that these VMs
are launched "later". POST_LAUNCHED_VM is closer to the fact
that these VMs are launched "later" by one of the VMs launched by ACRN.
Tracked-On: #3034
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In previous code, only for pre-launched VM, hypervisor would create
vuart console for each VM. But for post-launched VM, no vuart is
created.
In this patch, create vuart according to configuration in structure
acrn_vm_config. As the new configuration is set for pre-launched VM and
post-launched VM, and the vuart initialize process is common for each
VM, so, remove CONFIG_PARTITION_MODE from vuart related code.
Tracked-On: #2987
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add vuart config in acrn_vm_config struct, support configuring 2 vuarts for
each VM. The first vuart is used to work as VM's console. The second vuart
is used to connect to other VM's vuart. When the port base for a vuart
is set to 0, hypervisor will not create this vuart.
Tracked-On: #2987
Signed-off-by: Victor Sun <victor.sun@intel.com>
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
ACRN builds mptable for pre-launched VMs. It uses CONFIG_PARTITION_MODE
to compile mptable source code and related support. This patch removes
the macro and checks if the type of VM is pre-launched to build mptable.
Tracked-On: #2941
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Currently VM id of NORMAL_VM is allocated dymatically, we need to make
VM id statically for FuSa compliance.
This patch will pre-configure UUID for all VMs, then NORMAL_VM could
get its VM id/configuration from vm_configs array by indexing the UUID.
If UUID collisions is found in vm configs array, HV will refuse to
load the VM;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Return true if vm configs is sanitized successfully, otherwise return false;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The code mixed the usage on term of UUID and GUID, now use UUID to make
code more consistent, also will use lowercase (i.e. uuid) in variable name
definition.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously we use unified vm_config.c for all scenarios and use MACROs
for each configuration items, then the initialization of vm_configs[]
becomes more complicated when definition of MACROs increase, so change
the coding style that all configurable items could be explicitly shown in
vm_configuration.c to make code more readable.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously the vm_configs[] is defined separately for sharing mode and
partition mode, but the concept of hypervisor mode will be removed. Instead
we will introduce scenario Kconfig for hypervisor to load different vm
configurations.
SDC(Software Defined Cockpit) is a typical scenario that ACRN supported
so we introduce this scenario for previously sharing mode and move its
configurations to scenarios/sdc folder. The configuration could be used
for all boards reference.
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The vm_config in hypervisor restricted VM name size to
MAX_CONFIG_NAME_SIZE (32 bytes). When UOS is launched by DM, the vmname
is passed in as the last optional args, we hope to to copy it to vm_config
in the future. So the size of vmname in DM args should be restricted to
MAX_CONFIG_NAME_SIZE, too. Because MAX_CONFIG_NAME_SIZE will be used by DM,
we move it from vm_config.h to acrn_common.h
We also rename MAX_CONFIG_NAME_SIZE to MAX_VM_OS_NAME_LEN, because it will
be used by another components, should has a clear name.
Tracked-On: #2851
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
- for all cases of referring guest bootargs size, replace MEM_2K with
CONFIG_MAX_BOOTARGS_SIZE for better readability.
- remove duplicated MAX_BOOTARGS_SIZE definition from vm_config.h.
Also fix one minor issue in general_sw_loader() which uses copy_to_gpa()
to copy a string. Since copy_to_gpa() makes use of memncpy_s() to do the
job, the size parameter should include the string null ternimator.
Tracked-On: #2806
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
VM use CLOS when set CLOS_REQUIRED in guest flags of vm_config. The
wrong comment is 'if guest_flags has CAT_ENABLED', and should be fixed
as 'if guest_flags has CLOS_REQUIRED'
Tracked-On: #2462
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
- merge sharing_config.c and partition_config.c to vm_config.c;
- make vm_configs[] static;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
- move sanitize_vm_config() from vm.c to vm_config.c;
- move get_vm_config() from vm.h to vm_config.h;
Tracked-On: #2291
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
