'psram' and 'PSRAM' are legacy names and replaced
with 'ssram' and 'SSRAM' respectively.
Tracked-On: #6012
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Shuang Zheng <shuang.zheng@intel.com>
Define LIST_OF_VMX_MSRS which includes a list of MSRs that are visible to
L1 guests if nested virtualization is enabled.
- If CONFIG_NVMX_ENABLED is set, these MSRs are included in
emulated_guest_msrs[].
- otherwise, they are included in unsupported_msrs[].
In this way we can take advantage of the existing infrastructure to
emulate these MSRs.
Tracked-On: #5923
Spick igned-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In order to support nested virtualization, need to expose the "Enable VMX
outside SMX operation" bit to L1 hypervisor.
Tracked-On: #5923
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
For simplification purpose, use 'ssram' instead of
'software sram' for local names inside rtcm module.
Tracked-On: #6015
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Move Cache/TLB arch specific parts into cpu.h
After this change, we should not expose arch specific parts out from mmu.h
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Allow guest set CR4_VMXE if CONFIG_NVMX_ENABLED is set:
- move CR4_VMXE from CR4_EMULATED_RESERVE_BITS to CR4_TRAP_AND_EMULATE_BITS
so that CR4_VMXE is removed from cr4_reserved_bits_mask.
- force CR4_VMXE to be removed from cr4_rsv_bits_guest_value so that CR4_VMXE
is able to be set.
Expose VMX feature (CPUID01.01H:ECX[5]) to L1 guests whose GUEST_FLAG_NVMX_ENABLED
is set.
Assuming guest hypervisor (L1) is KVM, and KVM uses EPT for L2 guests.
Constraints on ACRN VM.
- LAPIC passthrough should be enabled.
- use SCHED_NOOP scheduler.
Tracked-On: #5923
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
moving invvpid and invept helper code from mmu.c to mmu.h, so that they
can be accessed by the nested virtualization code.
No logical changes.
Tracked-On: #5923
Signed-off-by: Zide Chen <zide.chen@intel.com>
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
TPAUSE, UMONITOR or UMWAIT instructions execution in guest VM cause
a #UD if "enable user wait and pause" (bit 26) of VMX_PROCBASED_CTLS2
is not set. To fix this issue, set the bit 26 of VMX_PROCBASED_CTLS2.
Besides, these WAITPKG instructions uses MSR_IA32_UMWAIT_CONTROL. So
load corresponding vMSR value during context switch in of a vCPU.
Please note, the TPAUSE or UMWAIT instruction causes a VM exit if the
"RDTSC exiting" and "enable user wait and pause" are both 1. In ACRN
hypervisor, "RDTSC exiting" is always 0. So TPAUSE or UMWAIT doesn't
cause a VM exit.
Performance impact:
MSR_IA32_UMWAIT_CONTROL read costs ~19 cycles;
MSR_IA32_UMWAIT_CONTROL write costs ~63 cycles.
Tracked-On: #6006
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
The current permission-checking and dispatching mechanism of hypercalls is
not unified because:
1. Some hypercalls require the exact vCPU initiating the call, while the
others only need to know the VM.
2. Different hypercalls have different permission requirements: the
trusty-related ones are enabled by a guest flag, while the others
require the initiating VM to be the Service OS.
Without a unified logic it could be hard to scale when more kinds of
hypercalls are added later.
The objectives of this patch are as follows.
1. All hypercalls have the same prototype and are dispatched by a unified
logic.
2. Permissions are checked by a unified logic without consulting the
hypercall ID.
To achieve the first objective, this patch modifies the type of the first
parameter of hcall_* functions (which are the callbacks implementing the
hypercalls) from `struct acrn_vm *` to `struct acrn_vcpu *`. The
doxygen-style documentations are updated accordingly.
To achieve the second objective, this patch adds to `struct hc_dispatch` a
`permission_flags` field which specifies the guest flags that must ALL be
set for a VM to be able to invoke the hypercall. The default value (which
is 0UL) indicates that this hypercall is for SOS only. Currently only the
`permission_flag` of trusty-related hypercalls have the non-zero value
GUEST_FLAG_SECURE_WORLD_ENABLED.
With `permission_flag`, the permission checking logic of hypercalls is
unified as follows.
1. General checks
i. If the VM is neither SOS nor having any guest flag that allows
certain hypercalls, it gets #UD upon executing the `vmcall`
instruction.
ii. If the VM is allowed to execute the `vmcall` instruction, but
attempts to execute it in ring 1, 2 or 3, the VM gets #GP(0).
2. Hypercall-specific checks
i. If the hypercall is for SOS (i.e. `permission_flag` is 0), the
initiating VM must be SOS and the specified target VM cannot be a
pre-launched VM. Otherwise the hypercall returns -EINVAL without
further actions.
ii. If the hypercall requires certain guest flags, the initiating VM
must have all the required flags. Otherwise the hypercall returns
-EINVAL without further actions.
iii. A hypercall with an unknown hypercall ID makes the hypercall
returns -EINVAL without further actions.
The logic above is different from the current implementation in the
following aspects.
1. A pre-launched VM now gets #UD (rather than #GP(0)) when it attempts
to execute `vmcall` in ring 1, 2 or 3.
2. A pre-launched VM now gets #UD (rather than the return value -EPERM)
when it attempts to execute a trusty hypercall in ring 0.
3. The SOS now gets the return value -EINVAL (rather than -EPERM) when it
attempts to invoke a trusty hypercall.
4. A post-launched VM with trusty support now gets the return value
-EINVAL (rather than #UD) when it attempts to invoke a non-trusty
hypercall or an invalid hypercall.
v1 -> v2:
- Update documentation that describe hypercall behavior.
- Fix Doxygen warnings
Tracked-On: #5924
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Instead of "#include <x86/foo.h>", use "#include <asm/foo.h>".
In other words, we are adopting the same practice in Linux kernel.
Tracked-On: #5920
Signed-off-by: Liang Yi <yi.liang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
We should only map [low32_max_ram, 4G) MMIO region as UC attribute,
not map [low32_max_ram, low32_max_ram + 4G) region as UC attribute.
Otherwise, the HV will complain [4G, low32_max_ram + 4G) region has
already mapped.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Both Windows guest and Linux guest use the MSR MSR_IA32_CSTAR, while
Linux uses it rarely. Now vcpu context switch doesn't save/restore it.
Windows detects the change of the MSR and rises a exception.
Do the save/resotre MSR_IA32_CSTAR during context switch.
Tracked-On: #5899
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
TLFS spec defines that when a VM is created, the value of
HV_X64_MSR_TIME_REF_COUNT is set to zero. Now tsc_offset is not
supported properly, so guest get a drifted reference time.
This patch implements tsc_offset. tsc_scale and tsc_offset
are calculated when a VM is launched and are saved in
struct acrn_hyperv of struct acrn_vm.
Tracked-On: #5956
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
TLFS spec defines that HV_X64_MSR_VP_INDEX and HV_X64_MSR_TIME_REF_COUNT
are read-only MSRs. Any attempt to write to them results in a #GP fault.
Fix the issue by returning error in handler hyperv_wrmsr() of MSRs
HV_X64_MSR_VP_INDEX/HV_X64_MSR_TIME_REF_COUNT emulation.
Tracked-On: #5956
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
TLFS spec defines different hypercall ABIs for X86 and x64. Currently
x64 hypercall interface is not supported well.
Setup the hypercall interface page according to the vcpu mode.
Tracked-On: #5956
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In order to support platform (such as Ander Lake) which physical address width
bits is 46, the current code need to reserve 2^16 PD page ((2^46) / (2^30)).
This is a complete waste of memory.
This patch would reserve PD page by three parts:
1. DRAM - may take PD_PAGE_NUM(CONFIG_PLATFORM_RAM_SIZE) PD pages at most;
2. low MMIO - may take PD_PAGE_NUM(MEM_1G << 2U) PD pages at most;
3. high MMIO - may takes (CONFIG_MAX_PCI_DEV_NUM * 6U) PD pages (may plus
PDPT entries if its size is larger than 1GB ) at most for:
(a) MMIO BAR size must be a power of 2 from 16 bytes;
(b) MMIO BAR base address must be power of two in size and are aligned with
its size.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
The platform which physical-address width over 39 bits must support
1GB large page (Both MMU and VMX sides ). This could save lots of
page table pages for EPT MMIO mapping.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
No one uses get_mem_range_info to get the top/bottom/size of the physical memory.
We could get these informations by e820 table easily.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: eddie Dong <eddie.dong@intel.com>
We used get_mem_range_info to get the top memory address and then use this address
as the high 64 bits max memory address of SOS. This assumes the platform must have
high memory space.
This patch removes the assumption. It will set high 64 bits max memory address of
SOS to 4G by default (Which means there's no 64 bits high memory), then update
the high 64 bits max memory address if the SOS really has high memory space.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: eddie Dong <eddie.dong@intel.com>
SOS's memory size could be calculated by its vE820 Tables easily.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: eddie Dong <eddie.dong@intel.com>
We used get_mem_range_info to get the top memory address and then use this address
as the high 64 bits max memory address. This assumes the platform must have high
memory space.
This patch calculates the high 64 bits max memory address according the e820 tables
and removes the assumption "The platform must have high memory space" by map the
low RAM region and high RAM region separately.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: eddie Dong <eddie.dong@intel.com>
Now BSP may launch VMs before APs have not done its initilization,
for example, sched_control for per-cpu. However, when we initilize
the vcpu thread data, it will access the object (scheduler) of the
sched_control of APs. As a result, it will trigger the PF.
This patch would waits each physical has done its initilization before
to continue to execute.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Using the MFENCE to make sure trampoline code
has been updated (clflush) into memory beforing start APs.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Use MFENCE to strengthen the fast string operations execute order to ensure
all trampoline code was updated before flush it into the memory.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
For platform with HLAT (Hypervisor-managed Linear Address Translation)
capability, the hypervisor shall hide this feature to its guest.
This patch adds MSR_IA32_VMX_PROCBASED_CTLS3 MSR to unsupported MSR
list.
The presence of this MSR is determined by 1-setting of bit 49 of MSR
MSR_IA32_VMX_PROCBASED_CTLS. which is already in unsupported MSR list. [2]
Related documentations:
[1] Intel Architecture Instruction Set Extensions, version Feb 16, 2021,
Ch 6.12
[2] Intel KeyLocker Specification, Sept 2020, Ch 7.2
Tracked-On: #5895
Signed-off-by: Yifan Liu <yifan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
sanitize_pte is used to set page table entry to map to an sanitized page to
mitigate l1tf. It should belongs to pgtable module. So move it to pagetable.c
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
lookup_address is used to lookup a pagetable entry by an address. So rename it
to pgtable_lookup_entry to indicate this clearly.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
alloc_page/free_page should been called in pagetable module. In order to do this,
we add pgtable_create_root and pgtable_create_trusty_root to create PML4 page table
page for normal world and secure world.
After this done, no one uses alloc_ept_page. So remove it.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Add pgtable_create_trusty_root to allocate a page for trusty PML4 page table page.
This function also copy PDPT entries from Normal world to Secure world.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Add pgtable_create_root to allocate a page for PMl4 page table page.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Rename mmu_add to pgtable_add_map;
Rename mmu_modify_or_del to pgtable_modify_or_del_map.
And move these functions declaration into pgtable.h
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Requires explicit arch path name in the include directive.
The config scripts was also updated to reflect this change.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Each .c file includes the arch specific irq header file (with full
path) by itself if required.
Tracked-On: #5825
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
A new x86/guest/virq.h head file now contains all guest
related interrupt handling API.
Tracked-On: #5825
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Each of them now resides in a separate .c file.
Tracked-On: #5825
Signed-off-by: Yang, Yu-chu <yu-chu.yang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The common irq file is responsible for managing the central
irq_desc data structure and provides the following APIs for
host interrupt handling.
- init_interrupt()
- reserve_irq_num()
- request_irq()
- free_irq()
- set_irq_trigger_mode()
- do_irq()
API prototypes, constant and data structures belonging to common
interrupt handling are all moved into include/common/irq.h.
Conversely, the following arch specific APIs are added which are
called from the common code at various points:
- init_irq_descs_arch()
- setup_irqs_arch()
- init_interrupt_arch()
- free_irq_arch()
- request_irq_arch()
- pre_irq_arch()
- post_irq_arch()
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
This is done be adding irq_rsvd_bitmap as an auxiliary bitmap
besides irq_alloc_bitmap.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The common IRQ handling routine calls arch specific functions
pre_irq_arch() and post_irq_arch() before and after calling the
registered action function respectively.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The common part initializes the global irq_desc data structure while the
arch specific part initialize the HW and its own irq data.
This is one of the preparation steps for spliting IRQ handling into common
and architecture specific parts.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Arch specific IRQ data is now an opaque pointer in irq_desc.
This is a preparation step for spliting IRQ handling into common
and architecture specific parts.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
This patch moves pgtable definition to pgtable.h and include the proper
header file for page module.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Move the EPT page table related APIs to ept.c. page module only provides APIs to
allocate/free page for page table page. pagetabl module only provides APIs to
add/modify/delete/lookup page table entry. The page pool and the page table
related APIs for EPT should defined in EPT module.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Move the MMU page table related APIs to mmu.c. page module only provides APIs to
allocate/free page for page table page. pagetabl module only provides APIs to
add/modify/delete/lookup page table entry. The page pool and the page table
related APIs for MMU should defined in MMU module.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
