Emulate Device ID, Vendor ID and MSE(Memory Space Enable) bit in
configuration space for an assigned VF, initialize assgined VF Bars.
The Device ID comes from PF's SRIOV capability
The Vendor ID comes from PF's Vendor ID
The PCI MSE bit always be set when VM reads from an assigned VF.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add cfg_header_read_cfg and cfg_header_write_cfg to handle the 1st 64B
CFG Space header PCI configuration space.
Only Command and Status Registers are pass through;
Only Command and Status Registers and Base Address Registers are writable.
In order to implement this, we add two type bit mask for per 4B register:
pass through mask and read-only mask. When pass through bit mask is set, this
means this bit of this 4B register is pass through, otherwise, it is virtualized;
When read-only mask is set, this means this bit of this 4B register is read-only,
otherwise, it's writable. We should write it to physical CFG space or virtual
CFG space base on whether the pass through bit mask is set or not.
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
1. Renames DEFINE_IOAPIC_SID with DEFINE_INTX_SID as the virtual source can
be IOAPIC or PIC
2. Rename the src member of source_id.intx_id to ctlr to indicate interrupt
controller
2. Changes the type of src member of source_id.intx_id from uint32_t to
enum with INTX_CTLR_IOAPIC and INTX_CTLR_PIC
Tracked-On: #4447
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
For SRIOV needs ARI support, so enable it in HV if
the PCI bridge support it.
TODO:
need check all the PCI devices under this bridge can support ARI,
if not, it is better not enable it as PCIe spec. That check will be
done when scanning PCI devices.
Tracked-On: #3381
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This is to enable relocation for code32.
- RIP relative addressing is available in x86-64 only so we manually add
relocation delta to the target symbols to fixup code32.
- both code32 and code64 need to load GDT hence both need to fixup GDT
pointer. This patch declares separate GDT pointer cpu_primary64_gdt_ptr
for code64 to avoid double fixup.
- manually fixup cpu_primary64_gdt_ptr in code64, but not rely on relocate()
to do that. Otherwise it's very confusing that symbols from same file could
be fixed up externally by relocate() or self-relocated.
- to make it clear, define a new symbol ld_entry_end representing the end of
the boot code that needs manually fixup, and use this symbol in relocate()
to filter out all symbols belong to the entry sections.
Tracked-On: #4441
Reviewed-by: Fengwei Yin <fengwei.yin@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
One argument is missing for the function ptirq_alloc_entry.
This patch fixes the doc generation error.
Tracked-On: #3882
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Fixed misspellings and rst formatting issues.
Added ptdev.h to the list of include file for doxygen
Tracked-On: #3882
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add doxygen style comments to ptdev public APIs.
Add these API descriptions to group acrn_passthrough.
Tracked-On: #3882
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
This patch adds RDT MBA support to detect, configure and
and setup MBA throttle registers based on VM configuration.
Tracked-On: #3725
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add a new parameter pf_vdev for function vpci_init_vdev to support SRIOV
VF vdev initializaiton.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The init_one_dev_config is used to initialize a acrn_vm_pci_dev_config
SRIOV needs a explicit acrn_vm_pci_dev_config to create a VF vdev,so
refine it to return acrn_vm_pci_dev_config.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Due to SRIOV VF physical device needs to be initialized when
VF_ENABLE is set and a SRIOV VF physical device initialization
is same with standard PCIe physical device, so expose the
init_pdev for SRIOV VF physical device initialization.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
All SRIOV VF physical devices don't have bars in configuration space,
they are from the VF associated PF's VF_BAR registers of SRIOV capability.
Adding a vbars data structure in pci_cap_sriov data structure to store
SRIOV VF_BAR information, so that each VF bars can be initialized directly
through the vbars instead multiple accessing of the PF VF_BAR registers.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Current code avoid the rule 88 S in MISRA-C, so move xsaves and xrstors
assembler to individual functions.
Tracked-On: #4436
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
VF_ENABLE is one field of SRIOV capability that is used to create
or remove VF physical devices. If VF_ENABLE is set, hv can detect
if the VF physical devices are ready after waiting 100 ms.
v2: Add sanity check for writing NumVFs register, add precondition
and application constraints when VF_ENABLE is set and refine
code style.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Introduce SRIOV capability field for pci_vdev and add SRIOV capability
interception entries.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Make the SRIOV-Capable device invisible from SOS if there is
no room for its all virtual functions.
v2: fix a issue that if a PF has been dropped, the subsequent PF
will be dropped too even there is room for its VFs.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
if the device has PCIe capability, walks all PCIe extended
capabilities for SRIOV discovery.
v2: avoid type casting and refine naming.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
add vpci bridge operations in hypervisor, to avoid SOS mis-operations
to affect other VM's PCI devices.
assumption: before hypervisor bootup, the physical pci-bridge shall be
configured correctly by BIOS or other bootloader; for ACS (Access
Control Service) capability, it is configured by BIOS to support the
devices under it to be isolated and allocated to different VMs.
to simplify the emulations of vpci bridge, set limitations as following:
1. expose all configure space registers, but readonly
2. BIST not support; by default is 0
3. not support interrupt, including INTx and MSI.
TODO:
1. configure tool can select whether a PCI bridge is emulated or pass
through.
Open:
1. SOS how to reset PCI device under the PCI bridge?
Tracked-On: #3381
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
The init value for XCR0 and XSS should be the same with spec:
In SDM Vol1 13.3:
XCR0[0] is associated with x87 state (see Section 13.5.1). XCR0[0] is
always 1. The other bits in XCR0 are all 0 coming out of RESET.
The IA32_XSS MSR (with MSR index DA0H) is zero coming out of RESET.
The previous code try to fix the xsave area leak to other VMs during init
phase, but bring the error to linux. Besides, it cannot avoid the
possible leak in running phase. Need find a better solution.
Tracked-On: #4430
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
is not set
This patch does the following,
1. Removes RDT code if CONFIG_RDT_ENABLED flag is
not set.
2. Set the CONFIG_RDT_ENABLED flag only on platforms
that support RDT so that build scripts will automatically
reflect the config.
Tracked-On: #3715
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
cache configuration.
This patch creates a generic infrastructure for
RDT resources instead of just L2 or L3 cache. This
patch also fixes L3 CAT config overwrite by L2 in
cases where both L2 and L3 CAT are supported.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There can be times when user unknowinlgy enables
CONFIG_CAT_ENBALED SW flag, but the hardware might
not support L3 or L2 CAT. In such case software can
end up writing to the CAT MSRs which can cause
undefined results. The patch fixes the issue by
enabling CAT only when both HW as well software
via the CONFIG_CAT_ENABLED supports CAT.
The patch also address typo with "clos2prq_msr"
function name. It should be "clos2pqr_msr" instead.
PQR stands for platform qos register.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Upcoming intel platforms can support both L2 and L3
but our current code only supports either L2 or L3 CAT.
So split the MSRs so that we can support allocation
for both L2 and L3.
This patch does the following,
1. splits programming of L2 and L3 cache resource
based on the resource ID.
2. Replace generic platform_clos_array struct with resource
specific struct in all the existing board.c files.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
As part of rdt cat refactoring, goal is to combine all rdt
specific features such as CAT under one module. So renaming
rdt resouce specific files such as cat.c/.h to generic rdt.c/.h
files.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Initialize efi info of acrn mbi when boot from multiboot2 protocol, with
this patch hypervisor could get host efi info and pass it to Linux zeropage,
then make guest Linux possible to boot with efi environment;
Tracked-On: #4419
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The patch re-arch boot component header files by:
- moving multiboot.h from include/arch/x86/ to boot/include/ and keep
this header for multiboot1 protocol data struct only;
- moving multiboot related MACROs in cpu_primary.S to multiboot.h;
- creating an independent boot.h to store acrn specific boot information
for other files' reference;
Tracked-On: #4419
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
BVT (Borrowed virtual time) scheduler is used to schedule vCPUs on pCPU.
It has the concept of virtual time, vCPU with earliset virtual time is
dispatched first.
Main concepts:
tick timer:
a period tick is used to measure the physcial time in units of MCU
(minimum charing unit).
runqueue:
thread in the runqueue is ordered by virtual time.
weight:
each thread receives a share of the pCPU in proportion to its
weight.
context switch allowance:
the physcial time by which the current thread is allowed to advance
beyond the next runnable thread.
warp:
a thread with warp enabled will have a change to minus a value (Wi)
from virtual time to achieve higher priority.
virtual time:
AVT: actual virtual time, advance in proportional to weight.
EVT: effective virtual time.
EVT <- AVT - ( warp ? Wi : 0 )
SVT: scheduler virtual time, the minimum AVT in the runqueue.
Tracked-On: #4410
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1. Rename BOOT_CPU_ID to BSP_CPU_ID
2. Repace hardcoded value with BSP_CPU_ID when
ID of BSP is referenced.
Tracked-On: #4420
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Now only PCI MSI-X BAR access need dynamic register/unregister. Others don't need
unregister once it's registered. So we don't need to lock the vm level emul_mmio_lock
when we handle the MMIO access. Instead, we could use finer granularity lock in the
handler to ptotest the shared resource.
This patch fixed the dead lock issue when OVMF try to size the BAR size:
Becasue OVMF use ECAM to access the PCI configuration space, it will first hold vm
emul_mmio_lock, then calls vpci_handle_mmconfig_access. While this tries to size a
BAR which is also a MSI-X Table BAR, it will call register_mmio_emulation_handler to
register the MSI-X Table BAR MMIO access handler. This will causes the emul_mmio_lock
dead lock.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Now we split passthrough PCI device from DM to HV, we could remove all the passthrough
PCI device unused code.
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add assign/deassign PCI device hypercall APIs to assign a PCI device from SOS to
post-launched VM or deassign a PCI device from post-launched VM to SOS. This patch
is prepared for spliting passthrough PCI device from DM to HV.
The old assign/deassign ptdev APIs will be discarded.
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
To enable gvt-d,need to allow the GPU IOMMU.
While gvt-d hasn't been enabled on APL yet,
so let APL disable GPU IOMMU.
v2 -> v3:
* let APL platforms disable GPU IOMMU.
Tracked-On: #4405
Signed-off-by: Junming Liu <junming.liu@intel.com>
Reviewed-by: Wu Binbin <binbin.wu@intel.com>
In platforms that support CAT, when it is enabled by ACRN, i.e.
IA32_resourceType_MASK_n registers are programmed with customized values,
it has impacts to the whole system.
The per guest flag GUEST_FLAG_CLOS_REQUIRED suggests that CAT may be
enabled in some guests, but not in others who don't have this flag,
which is conceptually incorrect.
This patch removes GUEST_FLAG_CLOS_REQUIRED, and adds a new Kconfig
entry CAT_ENABLED for CAT enabling. When it's enabled, platform_clos_array[]
defines a set of system-wide Class of Service (COS, or CLOS), and the
per guest vm_configs[].clos associates the guest with particular CLOS.
Tracked-On: #2462
Signed-off-by: Zide Chen <zide.chen@intel.com>
1. Align the coding style for these MACROs
2. Align the values of fixed VECTORs
Tracked-On: #4348
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
is_polling_ioreq is more straightforward. Rename it.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
'param' is BDF value instead of GPA when VHM driver
issues below 2 hypercalls:
- HC_ASSIGN_PTEDEV
- HC_DEASSIGN_PTDEV
This patch is to remove related code in hc_assign/deassign()
functions.
Tracked-On: #4334
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
SOS will use PCIe ECAM access PCIe external configuration space. HV should trap this
access for security(Now pre-launched VM doesn't want to support PCI ECAM; post-launched
VM trap PCIe ECAM access in DM).
Besides, update PCIe MMCONFIG region to be owned by hypervisor and expose and pass through
platform hide PCI devices by BIOS to SOS.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Use Enhanced Configuration Access Mechanism (MMIO) instead of PCI-compatible
Configuration Mechanism (IO port) to access PCIe Configuration Space
PCI-compatible Configuration Mechanism (IO port) access is used for UART in
debug version.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Sometimes HV wants to know if there are pending interrupts of one vcpu.
Add .has_pending_intr interface in acrn_apicv_ops and return the pending
interrupts status by check IRRs of apicv.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Introduce two kinds of events for each vcpu,
VCPU_EVENT_IOREQ: for vcpu waiting for IO request completion
VCPU_EVENT_VIRTUAL_INTERRUPT: for vcpu waiting for virtual interrupts events
vcpu can wait for such events, and resume to run when the
event get signalled.
This patch also change IO request waiting/notifying to this way.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This simple event implemention can only support exclusive waiting
at same time. It mainly used by thread who want to wait for special event
happens.
Thread A who want to wait for some events calls
wait_event(struct sched_event *);
Thread B who can give the event signal calls
signal_event(struct sched_event *);
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Before we assign a PT device to post-launched VM, we should reset the PCI device
first. However, ACRN hypervisor doesn't plan to support PCIe hot-plug and doesn't
support PCIe bridge Secondary Bus Reset. So the PT device must support FLR or PM
reset. This patch do this check when assigning a PT device to post-launched VM.
Tracked-On: #3465
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Since we restore BAR values when writing Command Register if necessary. We don't
need to trap FLR and do the BAR restore then.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
When PCIe does Conventinal Reset or FLR, almost PCIe configurations and states will
lost. So we should save the configurations and states before do the reset and restore
them after the reset. This was done well by BIOS or Guest now. However, ACRN will trap
these access and handle them properly for security. Almost of these configurations and
states will be written to physical configuration space at last except for BAR values
for now. So we should do the restore for BAR values. One way is to do restore after
one type reset is detected. This will be too complex. Another way is to do the restore
when BIOS or guest tries to write the Command Register. This could work because:
1. The I/O Space Enable bit and Memory Space Enable bits in Command Register will reset
to zero.
2. Before BIOS or guest wants to enable these bits, the BAR couldn't be accessed.
3. So we could restore the BAR values before enable these bits if reset is detected.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Per SDM 10.12.5.1 vol.3, local APIC should keep LAPIC state after receiving
INIT. The local APIC ID register should also be preserved.
Tracked-On: #4267
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The patch abstract a vcpu_reset_internal() api for internal usage, the
function would not touch any vcpu state transition and just do vcpu reset
processing. It will be called by create_vcpu() and reset_vcpu().
The reset_vcpu() will act as a public api and should be called
only when vcpu receive INIT or vm reset/resume from S3. It should not be
called when do shutdown_vm() or hcall_sos_offline_cpu(), so the patch remove
reset_vcpu() in shutdown_vm() and hcall_sos_offline_cpu().
The patch also introduced reset_mode enum so that vcpu and vlapic could do
different context operation according to different reset mode;
Tracked-On: #4267
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Some MACROs in lapic.h are duplicated with apicreg.h, and some MACROs are
never referenced, remove them.
Tracked-On: #4268
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Structure pci_vbar is used to define the virtual BAR rather than physical BAR.
It's better to name as pci_vbar.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add severity definitions for different scenarios. The static
guest severity is defined according to guest configurations.
Also add sanity check to make sure the severity for all guests
are correct.
Tracked-On: #4270
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
For guest reset, if the highest severity guest reset will reset
system. There is vm flag to call out the highest severity guest
in specific scenario which is a static guest severity assignment.
There is case that the static highest severity guest is shutdown
and the highest severity guest should be transfer to other guest.
For example, in ISD scenario, if RTVM (static highest severity
guest) is shutdown, SOS should be highest severity guest instead.
The is_highest_severity_vm() is updated to detect highest severity
guest dynamically. And promote the highest severity guest reset
to system reset.
Also remove the GUEST_FLAG_HIGHEST_SEVERITY definition.
Tracked-On: #4270
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
For system S5, ACRN had assumption that SOS shutdown will trigger
system shutdown. So the system shutdown logical is:
1. Trap SOS shutdown
2. Wait for all other guest shutdown
3. Shutdown system
The new logical is refined as:
If all guest is shutdown, shutdown whole system
Tracked-On: #4270
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
ACRN hypervisor should trap guest doing PCI AF FLR. Besides, it should save some status
before doing the FLR and restore them later, only BARs values for now.
This patch will trap guest Conventional PCI Advanced Features Control Register write
operation if the device supports Conventional PCI Advanced Features Capability and
check whether it wants to do device AF FLR. If it does, call pdev_do_flr to do the job.
Tracked-On: #3465
Signed-off-by: Li Fei1 <fei1.li@intel.com>
ACRN hypervisor should trap guest doing PCIe FLR. Besides, it should save some status
before doing the FLR and restore them later, only BARs values for now.
This patch will trap guest Device Capabilities Register write operation if the device
supports PCI Express Capability and check whether it wants to do device FLR. If it does,
call pdev_do_flr to do the job.
Tracked-On: #3465
Signed-off-by: Li Fei1 <fei1.li@intel.com>
We don't use INIT signal notification method now. This patch
removes them.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
We have implemented a new notification method using NMI.
So replace the INIT notification method with the NMI one.
Then we can remove INIT notification related code later.
Tracked-On: #3886
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
There is a window where we may miss the current request in the
notification period when the work flow is as the following:
CPUx + + CPUr
| |
| +--+
| | | Handle pending req
| <--+
+--+ |
| | Set req flag |
<--+ |
+------------------>---+
| Send NMI | | Handle NMI
| <--+
| |
| |
| +--> vCPU enter
| |
+ +
So, this patch enables the NMI-window exiting to trigger the next vmexit
once there is no "virtual-NMI blocking" after vCPU enter into VMX non-root
mode. Then we can process the pending request on time.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
The NMI for notification should not be inject to guest. So,
this patch drops NMI injection request when we use NMI
to notify vCPUs. Meanwhile, ACRN doesn't support vNMI well
and there is no well-designed way to check if the NMI is
for notification or for guest now. So, we take all the NMIs as
notificaton NMI for hard rtvm temporarily. It means that the
hard rtvm will never receive NMI with this patch applied.
TODO: vNMI support is not ready yet. we will add it later.
Tracked-On: #3886
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
ACRN hypervisor needs to kick vCPU off VMX non-root mode to do some
operations in hypervisor, such as interrupt/exception injection, EPT
flush etc. For non lapic-pt vCPUs, we can use IPI to do so. But, it
doesn't work for lapic-pt vCPUs as the IPI will be injected to VMs
directly without vmexit.
Without the way to kick the vCPU off VMX non-root mode to handle pending
request on time, there may be fatal errors triggered.
1). Certain operation may not be carried out on time which may further
lead to fatal errors. Taking the EPT flush request as an example, once we
don't flush the EPT on time and the guest access the out-of-date EPT,
fatal error happens.
2). ACRN now will send an IPI with vector 0xF0 to target vCPU to kick the vCPU
off VMX non-root mode if it wants to do some operations on target vCPU.
However, this way doesn't work for lapic-pt vCPUs. The IPI will be delivered
to the guest directly without vmexit and the guest will receive a unexpected
interrupt. Consequently, if the guest can't handle this interrupt properly,
fatal error may happen.
The NMI can be used as the notification signal to kick the vCPU off VMX
non-root mode for lapic-pt vCPUs. So, this patch uses NMI as notification signal
to address the above issues for lapic-pt vCPUs.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
Reserved bits in a 8-bit PAT field has been checked in pat_mem_type_invalid.
Remove this redundant check "(PAT_FIELD_RSV_BITS & field) != 0UL" in
write_pat_msr.
Tracked-On: #1842
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
This patch adds a helper function send_single_nmi. The fisrt caller
will soon come with the following patch.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
This patch installs a NMI handler in acrn IDT to handle
NMIs out of dispatch_exception.
Tracked-On: #3886
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Kaige Fu <kaige.fu@intel.com>
In current architecutre, the maximum vCPUs number per VM could not
exceed the pCPUs number. Given the MAX_PCPU_NUM macro is provided
in board configurations, so remove the MAX_VCPUS_PER_VM from Kconfig
and add a macro of MAX_VCPUS_PER_VM to reference MAX_PCPU_NUM directly.
Tracked-On: #4230
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
rename the macro since MAX_PCPU_NUM could be parsed from board file and
it is not a configurable item anymore.
Tracked-On: #4230
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
remove 'guest_init_pml4' and 'tmp_pg_array' in vm_arch
since they are not used.
Tracked-On: #1842
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Add yield support for schedule, which can give up pcpu proactively.
Tracked-On: #4178
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Signed-off-by: Yu Wang <yu1.wang@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
IO sensitive Round-robin scheduler aim to schedule threads with
round-robin policy. Meanwhile, we also enhance it with some fairness
configuration, such as thread will be scheduled out without properly
timeslice. IO request on thread will be handled in high priority.
This patch only add a skeleton for the sched_iorr scheduler.
Tracked-On: #4178
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Signed-off-by: Yu Wang <yu1.wang@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
On some platforms, HPA regions for Virtual Machine can not be
contiguous because of E820 reserved type or PCI hole. In such
cases, pre-launched VMs need to be assigned non-contiguous memory
regions and this patch addresses it.
To keep things simple, current design has the following assumptions,
1. HPA2 always will be placed after HPA1
2. HPA1 and HPA2 don’t share a single ve820 entry.
(Create multiple entries if needed but not shared)
3. Only support 2 non-contiguous HPA regions (can extend
at a later point for multiple non-contiguous HPA)
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Tracked-On: #4195
Acked-by: Anthony Xu <anthony.xu@intel.com>
1. disable physical MSI before writing the virtual MSI CFG space
2. do the remap_vmsi if the guest wants to enable MSI or update MSI address or data
3. disable INTx and enable MSI after step 2.
The previous Message Control check depends on the guest write MSI Message Control
Register at the offset of Message Control Register. However, the guest could access
this register at the offset of MSI Capability ID register. This patch remove this
constraint. Also, The previous implementation didn't really disable MSI when guest
wanted to disable MSI.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
With cpu-sharing enabled, there are more than 1 vcpu on 1 pcpu, so the
smp_call handler should switch the vmcs to the target vcpu's vmcs. Then
get the info.
dump_vcpu_reg and dump_guest_mem should run on certain vmcs, otherwise,
there will be #GP error.
Renaming:
vcpu_dumpreg -> dump_vcpu_reg
switch_vmcs -> load_vmcs
Tracked-On: #4178
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Deterministic is important for RTVM. The mitigation for MCE on
Page Size Change converts a large page to 4KB pages runtimely during
the vmexit triggered by the instruction fetch in the large page.
These vmexits increase nondeterminacy, which should be avoided for RTVM.
This patch builds 4KB page mapping in EPT for RTVM to avoid these vmexits.
Tracked-On: #4101
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Only apply the software workaround on the models that might be
affected by MCE on page size change. For these models that are
known immune to the issue, the mitigation is turned off.
Atom processors are not afftected by the issue.
Also check the CPUID & MSR to check whether the model is immune to the issue:
CPU is not vulnerable when both CPUID.(EAX=07H,ECX=0H).EDX[29] and
IA32_ARCH_CAPABILITIES[IF_PSCHANGE_MC_NO] are 1.
Other cases not listed above, CPU may be vulnerable.
This patch also changes MACROs for MSR IA32_ARCH_CAPABILITIES bits to UL instead of U
since the MSR is 64bit.
Tracked-On: #4101
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
After changing init_vmcs to smp call approach and do it before
launch_vcpu, it could work with noop scheduler. On real sharing
scheudler, it has problem.
pcpu0 pcpu1 pcpu1
vmBvcpu0 vmAvcpu1 vmBvcpu1
vmentry
init_vmcs(vmBvcpu1) vmexit->do_init_vmcs
corrupt current vmcs
vmentry fail
launch_vcpu(vmBvcpu1)
This patch mark a event flag when request vmcs init for specific vcpu. When
it is running and checking pending events, will do init_vmcs firstly.
Tracked-On: #4178
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The default PCI mmcfg base is stored in ACPI MCFG table, when
CONFIG_ACPI_PARSE_ENABLED is set, acpi_fixup() function will
parse and fix up the platform mmcfg base in ACRN boot stage;
when it is not set, platform mmcfg base will be initialized to
DEFAULT_PCI_MMCFG_BASE which generated by acrn-config tool;
Please note we will not support platform which has multiple PCI
segment groups.
Tracked-On: #4157
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
xsave area:
legacy region: 512 bytes
xsave header: 64 bytes
extended region: < 3k bytes
So, pre-allocate 4k area for xsave. Use certain instruction to save or
restore the area according to hardware xsave feature set.
Tracked-On: #4166
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Anthony Xu <anthony.xu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
ptirq_msix_remap doesn't do the real remap, that's the vmsi_remap and vmsix_remap_entry
does. ptirq_msix_remap only did the preparation.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Major changes:
1. Correct handling of device multi-function capability
We only check function zero for this feature. If it has it, we continue
looking at all remaining functions, ignoring those with invalid vendors.
The PCI spec says we are not to probe beyond function zero if it does
not exist or indicates it is not a multi-function device.
2a. Walk *ALL* buses in the PCI space, however,
Before walking the PCI hierarchy, post-processed ACPI DMAR info is parsed
and a map is created between all device-scopes across all DRHDs and the
corresponding IOMMU index.
This map is used at the time of walking the PCI hierarchy. If a BDF that
ACRN is currently working on, is found in the above-mentioned map, the
BDF device is mapped to the corresponding DRHD in the map.
If the BDF were a bridge type, realized with "Header Type" in config space,
the BDF device along with all its downstream devices are mapped to the
corresponding DRHD in the map.
To avoid walking previously visited buses, we maintain a bitmap that
stores which bus is walked when we handle Bridge type devices.
Once ACPI information is included into ACRN about the PCI-Express Root
Complexes / PCI Host Bridges, we can avoid the final loop which probes
all remainder buses, and instead jump to the next Host Bridge bus.
From prior patches, init_pdev returns the pdev structure it created to
the caller. This allows us to complete initialization by updating its
drhd_idx to the correct DRHD.
Tracked-On: #4134
Signed-off-by: Alexander Merritt <alex.merritt@intel.com>
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
We add new member pci_pdev.drhd_idx associating the DRHD
(IOMMU) with this pdev, and a method to convert a pbdf of a device to
this index by searching the pdev list.
Partial patch: drhd_index initialization handled in subsequent patch.
Tracked-On: #4134
Signed-off-by: Alexander Merritt <alex.merritt@intel.com>
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Add some encapsulation of utilities which read PCI header space using
wrapper functions. Also contain verification of PCI vendor to its own
function, rather than having hard-coded integrals exposed among other
code.
Tracked-On: #4134
Signed-off-by: Alexander Merritt <alex.merritt@intel.com>
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
add shell command to support dump dump guest memory
e.g.
dump_guest_mem vm_id, gva, length
Tracked-On: #4144
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The current code declare pci_bar structure following the PCI bar spec. However,
we could not tell whether the value in virtual BAR configuration space is valid
base address base on current pci_bar structure. We need to add more fields which
are duplicated instances of the vBAR information. Basides these fields which will
added, bar_base_mapped is another duplicated instance of the vBAR information.
This patch try to reshuffle the pci_bar structure to declare pci_bar structure
following the software implement benefit not the PCI bar spec.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
In 64-bit mode, processor pushes SS and RSP onto stack unconditionally.
Also when dumping the exception info, it makes more sense to dump
the RSP at the point of interrupt, rather than the RSP after pushing
context (including GPRs)
Tracked-On: #4102
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Issue description:
-----------------
Machine Check Error on Page Size Change
Instruction fetch may cause machine check error if page size
and memory type was changed without invalidation on some
processors[1][2]. Malicious guest kernel could trigger this issue.
This issue applies to both primary page table and extended page
tables (EPT), however the primary page table is controlled by
hypervisor only. This patch mitigates the situation in EPT.
Mitigation details:
------------------
Implement non-execute huge pages in EPT.
This patch series clears the execute permission (bit 2) in the
EPT entries for large pages. When EPT violation is triggered by
guest instruction fetch, hypervisor converts the large page to
smaller 4 KB pages and restore the execute permission, and then
re-execute the guest instruction.
The current patch turns on the mitigation by default.
The follow-up patches will conditionally turn on/off the feature
per processor model.
[1] Refer to erratum KBL002 in "7th Generation Intel Processor
Family and 8th Generation Intel Processor Family for U Quad Core
Platforms Specification Update"
https://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/7th-gen-core-family-spec-update.pdf
[2] Refer to erratum SKL002 in "6th Generation Intel Processor
Family Specification Update"
https://www.intel.com/content/www/us/en/products/docs/processors/core/desktop-6th-gen-core-family-spec-update.html
Tracked-On: #4101
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
MISRA C requires specified bounds for arrays declaration, previous declaration
of platform_clos_array in board.h does not meet the requirement.
Tracked-On: #3987
Signed-off-by: Victor Sun <victor.sun@intel.com>
The DMAR info is board specific so move the structure definition to board.c.
As a configruation file, the whole board.c could be generated by acrn-config
tool for each board.
Please note we only provide DMAR info MACROs for nuc7i7dnb board. For other
boards, ACPI_PARSE_ENABLED must be set to y in Kconfig to let hypervisor parse
DMAR info, or use acrn-config tool to generate DMAR info MACROs if user won't
enable ACPI parse code for FuSa consideration.
The patch also moves the function of get_dmar_info() to vtd.c, so dmar_info.c
could be removed.
Tracked-On: #3977
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The value of CONFIG_MAX_IOMMU and MAX_DRHDS are identical to DRHD_COUNT
which defined in platform ACPI table, so remove CONFIG_MAX_IOMMU_NUM
from Kconfig and link these three MACROs together.
Tracked-On: #3977
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Now the e820 structure store ACRN HV memory layout, not the physical memory layout.
Rename e820 to hv_hv_e820 to show this explicitly.
Tracked-On: #4007
Signed-off-by: Li Fei1 <fei1.li@intel.com>
After adding PCI BAR remap support, mmio_node may unregister when there's others
access it. This patch add a lock to protect mmio_node access.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Concurrent access on PCI device may happened if UOS try to access PCI configuration
space on different vCPUs through IO port. This patch just adds a global PCI lock for
each VM to prevent the concurrent access.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Refine PCI CONFIG_ADDRESS Register definition as its physical layout.
In this case, we could read/write PCI CONFIG_ADDRESS Register atomically.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Since guest could re-program PCI device MSI-X table BAR, we should add mmio
emulation handler unregister.
However, after add unregister_mmio_emulation_handler API, emul_mmio_regions
is no longer accurate. Just replace it with max_emul_mmio_regions which records
the max index of the emul_mmio_node.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
In theory, guest could re-program PCI BAR address to any address. However, ACRN
hypervisor only support [0, top_address_space) EPT memory mapping. So we need to
check whether the PCI BAR re-program address is within this scope.
Tracked-On: #3475
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
kick means to notify one thread_object. If the target thread object is
running, send a IPI to notify it; if the target thread object is
runnable, make reschedule on it.
Also add kick_vcpu API in vcpu layer to notify vcpu.
Tracked-On: #3813
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Signed-off-by: Yu Wang <yu1.wang@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
After moving softirq to following interrupt path, softirq handler might
break in the schedule spinlock context and try to grab the lock again,
then deadlock.
Disable interrupt with schedule spinlock context.
For the IRQ disable/restore operations:
CPU_INT_ALL_DISABLE(&rflag)
CPU_INT_ALL_RESTORE(rflag)
each takes 50~60 cycles.
renaming: get_schedule_lock -> obtain_schedule_lock
Tracked-On: #3813
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
