Two PSE-GPIO controllers of EHL CRB require MSI-X emulation for
pass-thru because it uses multiple MSI vectors. Currently acrn-config
enables MSI-X emulation for only TSN devices. Enable MSI-X emulation
for PSE-GPIOs, too.
Tracked-On: #5242
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
After below commit in https://github.com/zephyrproject-rtos/zephyr
commit d0126a037d23484feebba00d2c0eac27e6393fef
Author: Zide Chen <zide.chen@intel.com>
Date: Wed Feb 5 08:32:00 2020 -0800
boards/x86/acrn: build it in x86_64 mode and switch to X2APIC
The zephyr image for acrn would be built in x86_64 mode by default, then the
load/entry address for pre-launched Zephyr image should be changed from
0x100000 to 0x8000 accordingly per below definition in zephyr .ld file:
zephyrproject_src/zephyr/include/arch/x86/intel64/linker.ld
SECTIONS
{
/*
* The "locore" must be in the 64K of RAM, so that 16-bit code (with
* segment registers == 0x0000) and 32/64-bit code agree on addresses.
* ... there is no 16-bit code yet, but there will be when we add SMP.
*/
.locore 0x8000 : ALIGN(16)
{
_locore_start = .;
The commit in zephyrproject is merged before zephyr v2.2 release, so from v2.2
on, HV need this fix to boot Zephyr as pre-launched VM.
Tracked-On: #5259
Signed-off-by: Victor Sun <victor.sun@intel.com>
ACRN 2.1 supports two virtual boot modes, deprivilege boot mode and
direct boot mode. The deprivilege boot mode’s main purpose is to support
booting Clear Linux Service VM with UEFI service support, but this
brings scalability problems when porting ACRN to new Intel platforms.
For the 2.2 release, deprivilege mode is removed, and only direct boot
is supported, and with this we've removed support for Clear Linux as the
service VM, which impacts over 50 ACRN documents. This PR removes
documents we don't intend to update, and fixes broken links that would
occur from references to these deleted docs.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Convert SERIAL_PCI_BDF string value to hex value.
Tracked-On: #4937
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Tested-by: Shuo A Liu <shuo.a.liu@intel.com>
Users can add one or more ivshmem shm regions for uos when the shm
regions are configured from scenario setting.
Tracked-On: #4853
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
add shm_region config in default launch XMLs to configure Inter-
VM communication for post-launched VMs.
Tracked-On: #4853
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
This patch is to expose GPIO chassis interrupts as INTx to safety VM for
EHL. User can configure this per-VM attribute in scenario xml using the
following format:
<pt_intx desc="pt intx mapping.">
(phys_gsi0, virt_gsi0), (phys_gsi1, virt_gsi1), (phys_gsiN, virt_gsiN)
</pt_intx>
The physical and virtual interrupt gsi in each pair are separated by a
comma and enclosed in parentheses. If an integer begins with 0x or 0X,
it is hexadecimal, otherwise, it is assumed to be decimal. Example:
<pt_intx desc="pt intx mapping.">
(1, 0), (0x3, 1), (0x4, 2), (5, 6), (89, 0x12)
</pt_intx>
Tracked-On: #5241
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
This patch is to support direct assignment of P2SB bridge to one pre-launched
VM for EHL. User can configure this per-VM attribute in scenario xml:
<mmio_resources desc="MMIO resources.">
<p2sb>y</p2sb>
</mmio_resources>
Set p2sb to y to passthru P2SB bridge to VM, and n otherwise.
Tracked-On: #5221
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Add missing IVSHMEM tag in mrb board xml file to fix build issue
Correct misspelled function name
Use better error messages
Tracked-On: #5221
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Because ivshmem memory uses hv memory, if the ivshmem feature is
enabled, HV_RAM_SIZE will include IVSHMEM_SHM_SIZE.
Tracked-On: #4853
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
add hybrid_rt scenario for the ElkhartLake CRB board so that user can
launch Yocto Linux as pre-launched VM.
Tracked-On: #5238
Signed-off-by: "Nishioka, Toshiki" <toshiki.nishioka@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
1.Modify clos_mask and mba_delay as a member of the union type.
2.Move HV_SUPPORTED_MAX_CLOS ,MAX_CACHE_CLOS_NUM_ENTRIES and
MAX_MBA_CLOS_NUM_ENTRIES to misc_cfg.h file.
Tracked-On: #5229
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
1.Add macro MAX_CACHE_CLOS_NUM_ENTRIES for CAT, and MAX_MBA_CLOS_NUM_ENTRIES for MBA.
MAX_MBA_CLOS_NUM_ENTRIES:
Max number of Cache Mask entries corresponding to each CLOS.
This can vary if CDP is enabled vs disabled, as each CLOS entry will have corresponding
cache mask values for Data and Code when CDP is enabled.
MAX_CACHE_CLOS_NUM_ENTRIES:
Max number of MBA delay entries corresponding to each CLOS.
2.Move VMx_VCPU_CLOS macro to misc_cfg.h head file.
Tracked-On: #5229
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
HV_SUPPORTED_MAX_CLOS:
This value represents the maximum CLOS that is allowed by ACRN hypervisor.
This value is set to be least common Max CLOS (CPUID.(EAX=0x10,ECX=ResID):EDX[15:0])
among all supported RDT resources in the platform. In other words, it is
min(maximum CLOS of L2, L3 and MBA). This is done in order to have consistent
CLOS allocations between all the RDT resources.
Tracked-On: #5229
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
add IVSHMEM config in hybrid_rt scenario on tgl-rvp board.
Tracked-On: #4853
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
We use sos kernel cmdline maxcpus to limit the pCPU number of SOS
for hybrid or hybrid_rt scenarios by vcpu numbers calculation.
v2: add SOS CPU affinity calculation by total pCPU plus pCPUs
occupied by pre-launched VMs when no pcpuid configured
in SOS.
Tracked-On: #5216
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Reviewed-by: Victor Sun <victor.sun@intel.com>
Add cfl-k700-i7 board xml and its industry xml to support ACRN industry
scenario on cfl-k700-i7 board.
Tracked-On: #5212
Signed-off-by: Victor Sun <victor.sun@intel.com>
CPU sharing between pre-launch VMs and SOS, post-launch VMs were
forbidden.
Remove the limitation.
Tracked-On: #5153
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Terry Zou <terry.zou@intel.com>
This patch is to support the Inter-VM communication by IVSHMEM
in config tool.
Users can configure IVSHMEM_ENABLE to enable or disable Inter-VM
communication by IVSHMEM; users can configure the name, size,
communication VM IDs of the IVSHMEM devices in the VM settings of
scenario xmls, then config tool will generate the related IVSHMEM
configurations for Inter-VM communication.
The config tool will do sanity check including when saving the xmls:
the format of shared memory region configuration is
[name],[size],[VM ID]:[VM ID](:[VM ID]...);
the max size of the name is 32 bytes;
the names should not be duplicated;
the mininum value of shared memory region size is 2M;
the value of shared memory region is a power of 2;
the size of share memory region should not extended the size of
available ram.
Tracked-On: #4853
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Shared memory regoins can be added or deleted or updated from
scenario settings in config app with sanity check.
v2: move IVSHMEM config to hv->FEATURES->IVSHMEM
Tracked-On: #4853
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
add IVSHMEM_ENABLED and IVSHMEM_REGION in scenario xmls to support
Inter-VM communications configuration for VMs.
v2: move IVSHMEM config into <FEATURES> section
Tracked-On: #4853
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Enable TPM passthrough configuration for pre-launched VM feature, on
TGL, by adding 'tgl-rvp' to TPM_PASSTHRU_BOARD.
Tracked-On: #5205
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Get the max number with integer list to instead string 'number'.
Tracked-On: #5199
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
The default memory is 16G on TGL; the value of PLATFORM_RAM_SIZE and
SOS_RAM_SIZE is a little small in default xml.
Tracked-On: #5184
Reviewed-by: Victor Sun <victor.sun@intel.com>
Signed-off-by: fuzhongl <fuzhong.liu@intel.com>
add an IVSHMEM regoin and the related configuration parameters in
hybrid_rt scenario on whl-ipc-i5. The size of the shared memory is
2M, and it is used for the communication between VM0 and VM2.
v6: rename shm name; remove unnecessary MACROs.
v7: rename MACRO for shm name; add unassigned vbdf for post-launched
VMs.
Tracked-On: #4853
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Fix build issue while CDP_ENABLED=y for EHL-CRB-B.
Tracked-On: #5092
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
The default memory is 16G on TGL; the value of HV and sos
ramsize is a little small in default xml.
Tracked-On: # 5184
Signed-off-by: fuzhongl <fuzhong.liu@intel.com>
Add a comment for SOS_VM to indicate its VM ID for better understanding;
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
when CONFIG_MAX_MSIX_TABLE_NUM was set to 64, it will trigger timeout ASSERT
on WHL-I5 board.
Tracked-On: #5178
Signed-off-by: lirui34 <ruix.li@intel.com>
This patch will move the VM configuration check to pre-build stage,
a test program will do the check for pre-defined VM configuration
data before making hypervisor binary. If test failed, the make
process will be aborted. So once the hypervisor binary is built
successfully or start to run, it means the VM configuration has
been sanitized.
The patch did not add any new VM configuration check function,
it just port the original sanitize_vm_config() function from cpu.c
to static_checks.c with below change:
1. remove runtime rdt detection for clos check;
2. replace pr_err() from logmsg.h with printf() from stdio.h;
3. replace runtime call get_pcpu_nums() in ALL_CPUS_MASK macro
with static defined MAX_PCPU_NUM;
4. remove cpu_affinity check since pre-launched VM might share
pcpu with SOS VM;
The BOARD/SCENARIO parameter check and configuration folder check is
also moved to prebuild Makefile.
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add cpu_affinity setup for SOS VM. Cpu affinity must be set in
scenario XML, except if no pre-launched VM on the scenario and
all pCPUs will be assigned to SOS VM in that case;
Tracked-On: #5077
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Previously the CPU affinity of SOS VM is initialized at runtime during
sanitize_vm_config() stage, follow the policy that all physical CPUs
except ocuppied by Pre-launched VMs are all belong to SOS_VM. Now change
the process that SOS CPU affinity should be initialized at build time
and has the assumption that its validity is guarenteed before runtime.
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Set guest flag value for logical partition.
Tracked-On: #5119
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Remove RT guest flags from logical partition
configuration.
Tracked-On: #5119
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
The folders for config xmls and scenario setting source code are moved
to misc/vm_configs/xmls and misc/vm_configs/board, misc/vm_configs/scenario,
so this patch is to update config path for these folders.
Tracked-On: #5077
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Add xmls/samples folders under misc/vm_configs, and make soft link for
them.
Tracked-On: #5077
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Add hybrid_rt source code for whl-ipc-i5/i7.
Tracked-On: #5081
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
1.Refine cpu affinity in hybrid rt xmls for whl-ipc-i5/7
2.Refine guest flag for hybrid rt xmls for whl-ipc-i5/7
Tracked-On: #5081
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Add support to generate passthru TPM information for whl-ipc-i5/i7.
Tracked-On: #5077
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
There is some macro defined in misc_cfg.h while CAT/MBA enabled.
include the missing header to solve build issue.
Tracked-On: #5092
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Now the hypervisor configuration source code layout is changed, so acrn-config
need to change accordingly to make sure XML based configuration build success;
Tracked-On: #5077
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Add acrn-config tool formated nuc7i7dnb configurations code in misc/vm_configs/
folder with new layout;
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
The make command is same as old configs layout:
under acrn-hypervisor folder:
make hypervisor BOARD=xxx SCENARIO=xxx [TARGET_DIR]=xxx [RELEASE=x]
under hypervisor folder:
make BOARD=xxx SCENARIO=xxx [TARGET_DIR]=xxx [RELEASE=x]
if BOARD/SCENARIO parameter is not specified, the default will be:
BOARD=nuc7i7dnb SCENARIO=industry
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There are 3 kinds of configurations in ACRN hypervisor source code: hypervisor
overall setting, per-board setting and scenario specific per-VM setting.
Currently Kconfig act as hypervisor overall setting and its souce is located at
"hypervisor/arch/x86/configs/$(BOARD).config"; Per-board configs are located at
"hypervisor/arch/x86/configs/$(BOARD)" folder; scenario specific per-VM configs
are located at "hypervisor/scenarios/$(SCENARIO)" folder.
This layout brings issues that board configs and VM configs are coupled tightly.
The board specific Kconfig file and misc_cfg.h are shared by all scenarios, and
scenario specific pci_dev.c is shared by all boards. So the user have no way to
build hypervisor binary for different scenario on different board with one
source code repo.
The patch will setup a new VM configurations layout as below:
misc/vm_configs
├── boards --> folder of supported boards
│ ├── <board_1> --> scenario-irrelevant board configs
│ │ ├── board.c --> C file of board configs
│ │ ├── board_info.h --> H file of board info
│ │ ├── pci_devices.h --> pBDF of PCI devices
│ │ └── platform_acpi_info.h --> native ACPI info
│ ├── <board_2>
│ ├── <board_3>
│ └── <board...>
└── scenarios --> folder of supported scenarios
├── <scenario_1> --> scenario specific VM configs
│ ├── <board_1> --> board specific VM configs for <scenario_1>
│ │ ├── <board_1>.config --> Kconfig for specific scenario on specific board
│ │ ├── misc_cfg.h --> H file of board specific VM configs
│ │ ├── pci_dev.c --> board specific VM pci devices list
│ │ └── vbar_base.h --> vBAR base info of VM PT pci devices
│ ├── <board_2>
│ ├── <board_3>
│ ├── <board...>
│ ├── vm_configurations.c --> C file of scenario specific VM configs
│ └── vm_configurations.h --> H file of scenario specific VM configs
├── <scenario_2>
├── <scenario_3>
└── <scenario...>
The new layout would decouple board configs and VM configs completely:
The boards folder stores kinds of supported boards info, each board folder
stores scenario-irrelevant board configs only, which could be totally got from
a physical platform and works for all scenarios;
The scenarios folder stores VM configs of kinds of working scenario. In each
scenario folder, besides the generic scenario specific VM configs, the board
specific VM configs would be put in a embedded board folder.
In new layout, all configs files will be removed out of hypervisor folder and
moved to a separate folder. This would make hypervisor LoC calculation more
precisely with below fomula:
typical LoC = Loc(hypervisor) + Loc(one vm_configs)
which
Loc(one vm_configs) = Loc(misc/vm_configs/boards/<board>)
+ LoC(misc/vm_configs/scenarios/<scenario>/<board>)
+ Loc(misc/vm_configs/scenarios/<scenario>/vm_configurations.c
+ Loc(misc/vm_configs/scenarios/<scenario>/vm_configurations.h
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Update the draft content about Debian packaging with something more user
friendly and complete.
I removed the version of the release.json included in the doc and
instead just include the release.json file directly.
I added comments about the configuration parameters directly in the
release.json file, using the convention already being used there.
(If we updated the json python package being used to json5, the
release.json file could include comments using // convention and things
would look a bit cleaner.)
Tracked-On: #5022
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
1.Add UUID for Pre-launched RT VM.
2.Add hybrid_rt.xml for whl-ipc-i7/i5 and also add template Pre-Launched
RT sample xml.
3.Refine sanity check for load_kern_addr/entry.
Tracked-On: #5081
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
add tsn devices and the NVME device in the board xml
Tracked-On: #4831
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
Config tool should keep aligning with Kconfig default value for
MAX_MSIX_TABLE_NUM.
Note: Remain the same configuration for the board which does not have
PCIe slot or NVME slot.
Tracked-On: #4994
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
1.add max MSI-X table number in board xmls.
2.leave MAX_MSIX_TABLE_NUM item to blank.
Tracked-On: #4994
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Detect and get MSI-X table number in board xmls.
Parse and generate the number for board config while 'MAX_MSIX_TABLE_NUM'
item is blank.
Tracked-On: #4994
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
1.Update passtrough device config for ehl-crb-b launch xmls.
Tracked-On: #5016
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Add support 6 VMs for ehl-crb-b industry xml.
Tracked-On: #5015
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
MBA_DELAY/CLOS_MASK show be exposed only if "MBA"/"L2" or "L3" existed
in rdt resource supoorted in board xml;
The default value of MBA_DELAY is 0;
The numbers of MAB_DELAY/CLOS_MASK entries is determined by:
If CDP is not enabled, the number of entries for CLOS_MASK and MBA_DELAY
is the min of CLOS_MAX of all RDT resources;
If CDP is enabled, divide the CLOS_MAX values for L3 and L2 resources
by 2 and then find the min of all RDT resources to get common_clos_max,
the number of entries for CLOS_MASK is common_clos_max*2,
the number of entries for MBA_DELAY is comm_clos_max.
Tracked-On: #4943
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Reviewed-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Refine sanity check for RDT CLOS and MBA Delay.
Tracked-On: #4943
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Reviewed-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Update the LICENSE year for hv files which generate by config tool.
Tracked-On: #5004
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
The pci.ids database should be already prepared while tools of 'lspci'
were correctly installed and this check for pci.ids should be removed.
Tracked-On: #4989
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
For the base of vuart 1 is not an invalid com base, the tools will check
the target vuart id and it's VM id if matches the other VM's. If they do
not match the error message will report to re-configuration.
Tracked-On: #4991
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
1. add life-mngr as a target in misc/Makefile, so it is
convenient to build and used in Yocto system.
2. add install target in life-mngr/Makefile to be packaged
into device file-system.
Tracked-On: #4870
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
This patch adds support to configure MBA delay values from
scenario xml files just as it is done for CAT mask. This will
improve user experience when configuring RDT resource mask
values.
Tracked-On: #4943
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
There are three TSN devices on EHL CRB, and each of them need 32
vectors.
In order to support TSN devices, increase msix table size and irte
size.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
generate msix emulation information from known exist PCI devices for
board config.
Tracked-On: #4831
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Reviewed-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Don't hardcode install paths. Instead of hardcoding where binaries are
installed, add variables that installer can override.
Tracked-On: #4864
Signed-off-by: Chee Yang Lee <chee.yang.lee@intel.com>
Signed-off-by: Naveen Saini <naveen.kumar.saini@intel.com>
refine sanity check for MASK_CLOS number by max clos in board xml.
Tracked-On: #4876
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
1.Refinement GVT args for SOS kernel cmdline in scenario config xmls.
2.Refinement GVT args for launch UOS script in launch config xmls.
Tracked-On: #4869
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
1.Update efi bootloader image file path for Yocto rootfs.
2.Remove empty check for UEFI OS loader name.
Tracked-On: #4868
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Update mrb ttys, up2 iomem and ehl-crb-b information.
Tracked-On: #4862
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
Currently, MMIO PCI BDF of ttyS was indexed by IRQ, but it may found
the wrong BDF when the IRQ was shared and it is not expected. So, the
patch uses the MMIO base to query /proc/iomem to find BDF, the waring
will get if BDF is not present in iomem.
Tracked-On: #4862
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
RDT config item is located in the 5rd layer of scenario config;
the number of CLOS_MASK config is dynamically obtained by the rdt
resource clos max in the board config;
the vcpu_clos config is dynamically added or removed when the
pcpu_id config is added or removed;
the drop-down list of vcpu_clos config is reduced by half when
CDP_ENABLED=y.
Tracked-On: #4860
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Reviewed-by: Victor Sun <victor.sun@intel.com>
1.Add parser and sanity check for RDT_ENABLED/CDP_ENABLED/CLOS_MASK.
2.Skip to generate RDT inforamtion when HW not support RDT or usr
select 'n' to disable RDT feature.
3.Add contiguous bit 1 check for CLOS_MASK.
Tracked-On: #4860
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
1.Add RDT feature in scenario xmls, add set RDT_ENABLED=y, CDP_ENABLED=n
by default for industry scenario if HW support RDT.
2.Add CLOS_MASK in xmls to configurable and set them to '0xff' by
default if HW support RDT.
3.Remove configurable="0" of clos for PRE launched VM and POST VM, currently,
remain configurable="0" for SOS VM.
4.Add vcpu_clos to match the pcpu_id number, and set vcpu_clos to 0.
Tracked-On: #4860
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
This patch adds xml file, both board as well scenario files
that are need to run ACRN on top of QEMU as a nested hypervisor.
Currently support is only for SDC scenario.
Tracked-On: #3198
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
This patch sets defaults similar to generic platform configuration
when leaf features like PM_INFO, S3_INFO, S5_INFO, DRHD_INFO, CPU_BRAND,
CX_INFO, PX_INFO, MMCFG_BASE_INFO are not generated via either target
offline tool or user supplies empty field in case of emulation.
Tracked-On: #3198
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Victor Sun <victor.sun@intel.com>
