Emulate Device ID, Vendor ID and MSE(Memory Space Enable) bit in
configuration space for an assigned VF, initialize assgined VF Bars.
The Device ID comes from PF's SRIOV capability
The Vendor ID comes from PF's Vendor ID
The PCI MSE bit always be set when VM reads from an assigned VF.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add cfg_header_read_cfg and cfg_header_write_cfg to handle the 1st 64B
CFG Space header PCI configuration space.
Only Command and Status Registers are pass through;
Only Command and Status Registers and Base Address Registers are writable.
In order to implement this, we add two type bit mask for per 4B register:
pass through mask and read-only mask. When pass through bit mask is set, this
means this bit of this 4B register is pass through, otherwise, it is virtualized;
When read-only mask is set, this means this bit of this 4B register is read-only,
otherwise, it's writable. We should write it to physical CFG space or virtual
CFG space base on whether the pass through bit mask is set or not.
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
1. Renames DEFINE_IOAPIC_SID with DEFINE_INTX_SID as the virtual source can
be IOAPIC or PIC
2. Rename the src member of source_id.intx_id to ctlr to indicate interrupt
controller
2. Changes the type of src member of source_id.intx_id from uint32_t to
enum with INTX_CTLR_IOAPIC and INTX_CTLR_PIC
Tracked-On: #4447
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
For SRIOV needs ARI support, so enable it in HV if
the PCI bridge support it.
TODO:
need check all the PCI devices under this bridge can support ARI,
if not, it is better not enable it as PCIe spec. That check will be
done when scanning PCI devices.
Tracked-On: #3381
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This is to enable relocation for code32.
- RIP relative addressing is available in x86-64 only so we manually add
relocation delta to the target symbols to fixup code32.
- both code32 and code64 need to load GDT hence both need to fixup GDT
pointer. This patch declares separate GDT pointer cpu_primary64_gdt_ptr
for code64 to avoid double fixup.
- manually fixup cpu_primary64_gdt_ptr in code64, but not rely on relocate()
to do that. Otherwise it's very confusing that symbols from same file could
be fixed up externally by relocate() or self-relocated.
- to make it clear, define a new symbol ld_entry_end representing the end of
the boot code that needs manually fixup, and use this symbol in relocate()
to filter out all symbols belong to the entry sections.
Tracked-On: #4441
Reviewed-by: Fengwei Yin <fengwei.yin@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
One argument is missing for the function ptirq_alloc_entry.
This patch fixes the doc generation error.
Tracked-On: #3882
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Fixed misspellings and rst formatting issues.
Added ptdev.h to the list of include file for doxygen
Tracked-On: #3882
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Add doxygen style comments to ptdev public APIs.
Add these API descriptions to group acrn_passthrough.
Tracked-On: #3882
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
This patch adds RDT MBA support to detect, configure and
and setup MBA throttle registers based on VM configuration.
Tracked-On: #3725
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add a new parameter pf_vdev for function vpci_init_vdev to support SRIOV
VF vdev initializaiton.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The init_one_dev_config is used to initialize a acrn_vm_pci_dev_config
SRIOV needs a explicit acrn_vm_pci_dev_config to create a VF vdev,so
refine it to return acrn_vm_pci_dev_config.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Due to SRIOV VF physical device needs to be initialized when
VF_ENABLE is set and a SRIOV VF physical device initialization
is same with standard PCIe physical device, so expose the
init_pdev for SRIOV VF physical device initialization.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
All SRIOV VF physical devices don't have bars in configuration space,
they are from the VF associated PF's VF_BAR registers of SRIOV capability.
Adding a vbars data structure in pci_cap_sriov data structure to store
SRIOV VF_BAR information, so that each VF bars can be initialized directly
through the vbars instead multiple accessing of the PF VF_BAR registers.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Current code avoid the rule 88 S in MISRA-C, so move xsaves and xrstors
assembler to individual functions.
Tracked-On: #4436
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
VF_ENABLE is one field of SRIOV capability that is used to create
or remove VF physical devices. If VF_ENABLE is set, hv can detect
if the VF physical devices are ready after waiting 100 ms.
v2: Add sanity check for writing NumVFs register, add precondition
and application constraints when VF_ENABLE is set and refine
code style.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Introduce SRIOV capability field for pci_vdev and add SRIOV capability
interception entries.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Make the SRIOV-Capable device invisible from SOS if there is
no room for its all virtual functions.
v2: fix a issue that if a PF has been dropped, the subsequent PF
will be dropped too even there is room for its VFs.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
if the device has PCIe capability, walks all PCIe extended
capabilities for SRIOV discovery.
v2: avoid type casting and refine naming.
Tracked-On: #4433
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
add vpci bridge operations in hypervisor, to avoid SOS mis-operations
to affect other VM's PCI devices.
assumption: before hypervisor bootup, the physical pci-bridge shall be
configured correctly by BIOS or other bootloader; for ACS (Access
Control Service) capability, it is configured by BIOS to support the
devices under it to be isolated and allocated to different VMs.
to simplify the emulations of vpci bridge, set limitations as following:
1. expose all configure space registers, but readonly
2. BIST not support; by default is 0
3. not support interrupt, including INTx and MSI.
TODO:
1. configure tool can select whether a PCI bridge is emulated or pass
through.
Open:
1. SOS how to reset PCI device under the PCI bridge?
Tracked-On: #3381
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
The init value for XCR0 and XSS should be the same with spec:
In SDM Vol1 13.3:
XCR0[0] is associated with x87 state (see Section 13.5.1). XCR0[0] is
always 1. The other bits in XCR0 are all 0 coming out of RESET.
The IA32_XSS MSR (with MSR index DA0H) is zero coming out of RESET.
The previous code try to fix the xsave area leak to other VMs during init
phase, but bring the error to linux. Besides, it cannot avoid the
possible leak in running phase. Need find a better solution.
Tracked-On: #4430
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
is not set
This patch does the following,
1. Removes RDT code if CONFIG_RDT_ENABLED flag is
not set.
2. Set the CONFIG_RDT_ENABLED flag only on platforms
that support RDT so that build scripts will automatically
reflect the config.
Tracked-On: #3715
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
cache configuration.
This patch creates a generic infrastructure for
RDT resources instead of just L2 or L3 cache. This
patch also fixes L3 CAT config overwrite by L2 in
cases where both L2 and L3 CAT are supported.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There can be times when user unknowinlgy enables
CONFIG_CAT_ENBALED SW flag, but the hardware might
not support L3 or L2 CAT. In such case software can
end up writing to the CAT MSRs which can cause
undefined results. The patch fixes the issue by
enabling CAT only when both HW as well software
via the CONFIG_CAT_ENABLED supports CAT.
The patch also address typo with "clos2prq_msr"
function name. It should be "clos2pqr_msr" instead.
PQR stands for platform qos register.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Upcoming intel platforms can support both L2 and L3
but our current code only supports either L2 or L3 CAT.
So split the MSRs so that we can support allocation
for both L2 and L3.
This patch does the following,
1. splits programming of L2 and L3 cache resource
based on the resource ID.
2. Replace generic platform_clos_array struct with resource
specific struct in all the existing board.c files.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
As part of rdt cat refactoring, goal is to combine all rdt
specific features such as CAT under one module. So renaming
rdt resouce specific files such as cat.c/.h to generic rdt.c/.h
files.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Initialize efi info of acrn mbi when boot from multiboot2 protocol, with
this patch hypervisor could get host efi info and pass it to Linux zeropage,
then make guest Linux possible to boot with efi environment;
Tracked-On: #4419
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The patch re-arch boot component header files by:
- moving multiboot.h from include/arch/x86/ to boot/include/ and keep
this header for multiboot1 protocol data struct only;
- moving multiboot related MACROs in cpu_primary.S to multiboot.h;
- creating an independent boot.h to store acrn specific boot information
for other files' reference;
Tracked-On: #4419
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
BVT (Borrowed virtual time) scheduler is used to schedule vCPUs on pCPU.
It has the concept of virtual time, vCPU with earliset virtual time is
dispatched first.
Main concepts:
tick timer:
a period tick is used to measure the physcial time in units of MCU
(minimum charing unit).
runqueue:
thread in the runqueue is ordered by virtual time.
weight:
each thread receives a share of the pCPU in proportion to its
weight.
context switch allowance:
the physcial time by which the current thread is allowed to advance
beyond the next runnable thread.
warp:
a thread with warp enabled will have a change to minus a value (Wi)
from virtual time to achieve higher priority.
virtual time:
AVT: actual virtual time, advance in proportional to weight.
EVT: effective virtual time.
EVT <- AVT - ( warp ? Wi : 0 )
SVT: scheduler virtual time, the minimum AVT in the runqueue.
Tracked-On: #4410
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1. Rename BOOT_CPU_ID to BSP_CPU_ID
2. Repace hardcoded value with BSP_CPU_ID when
ID of BSP is referenced.
Tracked-On: #4420
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Now only PCI MSI-X BAR access need dynamic register/unregister. Others don't need
unregister once it's registered. So we don't need to lock the vm level emul_mmio_lock
when we handle the MMIO access. Instead, we could use finer granularity lock in the
handler to ptotest the shared resource.
This patch fixed the dead lock issue when OVMF try to size the BAR size:
Becasue OVMF use ECAM to access the PCI configuration space, it will first hold vm
emul_mmio_lock, then calls vpci_handle_mmconfig_access. While this tries to size a
BAR which is also a MSI-X Table BAR, it will call register_mmio_emulation_handler to
register the MSI-X Table BAR MMIO access handler. This will causes the emul_mmio_lock
dead lock.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Now we split passthrough PCI device from DM to HV, we could remove all the passthrough
PCI device unused code.
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add assign/deassign PCI device hypercall APIs to assign a PCI device from SOS to
post-launched VM or deassign a PCI device from post-launched VM to SOS. This patch
is prepared for spliting passthrough PCI device from DM to HV.
The old assign/deassign ptdev APIs will be discarded.
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
To enable gvt-d,need to allow the GPU IOMMU.
While gvt-d hasn't been enabled on APL yet,
so let APL disable GPU IOMMU.
v2 -> v3:
* let APL platforms disable GPU IOMMU.
Tracked-On: #4405
Signed-off-by: Junming Liu <junming.liu@intel.com>
Reviewed-by: Wu Binbin <binbin.wu@intel.com>
In platforms that support CAT, when it is enabled by ACRN, i.e.
IA32_resourceType_MASK_n registers are programmed with customized values,
it has impacts to the whole system.
The per guest flag GUEST_FLAG_CLOS_REQUIRED suggests that CAT may be
enabled in some guests, but not in others who don't have this flag,
which is conceptually incorrect.
This patch removes GUEST_FLAG_CLOS_REQUIRED, and adds a new Kconfig
entry CAT_ENABLED for CAT enabling. When it's enabled, platform_clos_array[]
defines a set of system-wide Class of Service (COS, or CLOS), and the
per guest vm_configs[].clos associates the guest with particular CLOS.
Tracked-On: #2462
Signed-off-by: Zide Chen <zide.chen@intel.com>
1. Align the coding style for these MACROs
2. Align the values of fixed VECTORs
Tracked-On: #4348
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
is_polling_ioreq is more straightforward. Rename it.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
'param' is BDF value instead of GPA when VHM driver
issues below 2 hypercalls:
- HC_ASSIGN_PTEDEV
- HC_DEASSIGN_PTDEV
This patch is to remove related code in hc_assign/deassign()
functions.
Tracked-On: #4334
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
SOS will use PCIe ECAM access PCIe external configuration space. HV should trap this
access for security(Now pre-launched VM doesn't want to support PCI ECAM; post-launched
VM trap PCIe ECAM access in DM).
Besides, update PCIe MMCONFIG region to be owned by hypervisor and expose and pass through
platform hide PCI devices by BIOS to SOS.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Use Enhanced Configuration Access Mechanism (MMIO) instead of PCI-compatible
Configuration Mechanism (IO port) to access PCIe Configuration Space
PCI-compatible Configuration Mechanism (IO port) access is used for UART in
debug version.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Sometimes HV wants to know if there are pending interrupts of one vcpu.
Add .has_pending_intr interface in acrn_apicv_ops and return the pending
interrupts status by check IRRs of apicv.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Introduce two kinds of events for each vcpu,
VCPU_EVENT_IOREQ: for vcpu waiting for IO request completion
VCPU_EVENT_VIRTUAL_INTERRUPT: for vcpu waiting for virtual interrupts events
vcpu can wait for such events, and resume to run when the
event get signalled.
This patch also change IO request waiting/notifying to this way.
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This simple event implemention can only support exclusive waiting
at same time. It mainly used by thread who want to wait for special event
happens.
Thread A who want to wait for some events calls
wait_event(struct sched_event *);
Thread B who can give the event signal calls
signal_event(struct sched_event *);
Tracked-On: #4329
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Before we assign a PT device to post-launched VM, we should reset the PCI device
first. However, ACRN hypervisor doesn't plan to support PCIe hot-plug and doesn't
support PCIe bridge Secondary Bus Reset. So the PT device must support FLR or PM
reset. This patch do this check when assigning a PT device to post-launched VM.
Tracked-On: #3465
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Since we restore BAR values when writing Command Register if necessary. We don't
need to trap FLR and do the BAR restore then.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
When PCIe does Conventinal Reset or FLR, almost PCIe configurations and states will
lost. So we should save the configurations and states before do the reset and restore
them after the reset. This was done well by BIOS or Guest now. However, ACRN will trap
these access and handle them properly for security. Almost of these configurations and
states will be written to physical configuration space at last except for BAR values
for now. So we should do the restore for BAR values. One way is to do restore after
one type reset is detected. This will be too complex. Another way is to do the restore
when BIOS or guest tries to write the Command Register. This could work because:
1. The I/O Space Enable bit and Memory Space Enable bits in Command Register will reset
to zero.
2. Before BIOS or guest wants to enable these bits, the BAR couldn't be accessed.
3. So we could restore the BAR values before enable these bits if reset is detected.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Per SDM 10.12.5.1 vol.3, local APIC should keep LAPIC state after receiving
INIT. The local APIC ID register should also be preserved.
Tracked-On: #4267
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
