x86/timer.[ch] was moved to the common directory largely unchanged.
x86 specific code now resides in x86/tsc_deadline_timer.c and its
interface was defined in hw/hw_timer.h. The interface defines two
functions: init_hw_timer() and set_hw_timeout() that provides HW
specific initialization and timer interrupt source.
Other than these two functions, the timer module is largely arch
agnostic.
Tracked-On: #5920
Signed-off-by: Rong Liu <rong2.liu@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Modules that use udelay() should include "delay.h" explicitly.
Tracked-On: #5920
Signed-off-by: Rong Liu <rong2.liu@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Generalize and split basic cpu cycle/tick routines from x86/timer:
- Instead of rdstc(), use cpu_ticks() in generic code.
- Instead of get_tsc_khz(), use cpu_tickrate() in generic code.
- Include "common/ticks.h" instead of "x86/timer.h" in generic code.
- CYCLES_PER_MS is renamed to TICKS_PER_MS.
The x86 specific API rdstc() and get_tsc_khz(), as well as TSC_PER_MS
are still available in arch/x86/tsc.h but only for x86 specific usage.
Tracked-On: #5920
Signed-off-by: Rong Liu <rong2.liu@intel.com>
Signed-off-by: Yi Liang <yi.liang@intel.com>
Instead of "#include <x86/foo.h>", use "#include <asm/foo.h>".
In other words, we are adopting the same practice in Linux kernel.
Tracked-On: #5920
Signed-off-by: Liang Yi <yi.liang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Now BSP may launch VMs before APs have not done its initilization,
for example, sched_control for per-cpu. However, when we initilize
the vcpu thread data, it will access the object (scheduler) of the
sched_control of APs. As a result, it will trigger the PF.
This patch would waits each physical has done its initilization before
to continue to execute.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Using the MFENCE to make sure trampoline code
has been updated (clflush) into memory beforing start APs.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Requires explicit arch path name in the include directive.
The config scripts was also updated to reflect this change.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Each .c file includes the arch specific irq header file (with full
path) by itself if required.
Tracked-On: #5825
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Move the EPT page table related APIs to ept.c. page module only provides APIs to
allocate/free page for page table page. pagetabl module only provides APIs to
add/modify/delete/lookup page table entry. The page pool and the page table
related APIs for EPT should defined in EPT module.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Per-core software SRAM L2 cache may be flushed by 'mwait'
extension instruction, which guest VM may execute to enter
core deep sleep. Such kind of flushing is not expected when
software SRAM is enabled for RTVM.
Hypervisor disables MONITOR-WAIT support on both hypervisor
and VMs sides to protect above software SRAM from being flushed.
This patch disable hypervisor(host) MONITOR-WAIT support and refine
software sram initializaion flow.
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
For FuSa's case, we remove all dynamic memory allocation use in ACRN HV. Instead,
we use static memory allocation or embedded data structure. For pagetable page,
we prefer to use an index (hva for MMU, gpa for EPT) to get a page from a special
page pool. The special page pool should be big enougn for each possible index.
This is not a big problem when we don't support 64 bits MMIO. Without 64 bits MMIO
support, we could use the index to search addrss not larger than DRAM_SIZE + 4G.
However, if ACRN plan to support 64 bits MMIO in SOS, we could not use the static
memory alocation any more. This is because there's a very huge hole between the
top DRAM address and the bottom 64 bits MMIO address. We could not reserve such
many pages for pagetable mapping as the CPU physical address bits may very large.
This patch will use dynamic page allocation for pagetable mapping. We also need
reserve a big enough page pool at first. For HV MMU, we don't use 4K granularity
page table mapping, we need reserve PML4, PDPT and PD pages according the maximum
physical address space (PPT va and pa are identical mapping); For each VM EPT,
we reserve PML4, PDPT and PD pages according to the maximum physical address space
too, (the EPT address sapce can't beyond the physical address space), and we reserve
PT pages by real use cases of DRAM, low MMIO and high MMIO.
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Tracked-On: #5788
In previous code, the rsdp initialization is done in get_rsdp() api implicitly.
The function is called multiple times in following acpi table parsing functions
and the condition (rsdp == NULL) need to be added in each parsing function.
This is not needed since the panic would occur if rsdp is NULL when do acpi
initialization.
Tracked-On: #5626
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
KeyLocker is a new security feature available in new Intel CPUs that
protects data-encryption keys for the Advanced Encryption Standard (AES)
algorithm.
This patch emulates Keylocker CPUID leaf 19H to support Keylocker
feature for guest VM.
To make the hypervisor being able to manage the IWKey correctly, this
patch doesn't expose hardware random IWKey capability
(CPUID.0x19.ECX[1]) to guest VM.
Tracked-On: #5695
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
'ptcm' and 'ptct' are legacy name according
to the latest TCC spec, hence rename below files
to avoid confusing:
ptcm.c -> rtcm.c
ptcm.h -> rtcm.h
ptct.h -> rtct.h
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Calling sanitize_multiboot() from init.c instead of cpu.c.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Use ept_flush_leaf_page to emulate guest WBINVD when PTCM is enabled and skip
the pSRAM in ept_flush_leaf_page.
TODO: do we need to emulate WBINVD in HV side.
Tracked-On: #5330
Signed-off-by: Qian Wang <qian1.wang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1.We added a function init_psram to initialize pSRAM as well as some definitions.
Both AP and BSP shall call init_psram to make sure pSRAM is initialized, which is
required by PTCM.
BSP:
To parse PTCT and find the entry of PTCM command function, then call PTCM ABI.
AP:
Wait until BSP has done the parsing work, then call the PTCM ABI.
Synchronization of AP and BSP is ensured, both inside and outside PTCM.
2. Added calls of init_psram in init_pcpu_post to initialize pSRAM in HV booting phase
Tracked-On: #5330
Signed-off-by: Qian Wang <qian1.wang@intel.com>
Add cteate method for vmcs9900 vdev in hypercalls.
The destroy method of ivshmem is also suitable for other emulated vdev,
move it into hcall_destroy_vdev() for all emulated vdevs
Tracked-On: #5394
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
Now ACRN supports direct boot mode, which could be SBL/ABL, or GRUB boot.
Thus the vboot wrapper layer can be removed and the direct boot functions
don't need to be wrapped in direct_boot.c:
- remove call to init_vboot(), and call e820_alloc_memory() directly at the
time when the trampoline buffer is actually needed.
- Similarly, call CPU_IRQ_ENABLE() instead of the wrapper init_vboot_irq().
- remove get_ap_trampoline_buf(), since the existing function
get_trampoline_start16_paddr() returns the exact same value.
- merge init_general_vm_boot_info() into init_vm_boot_info().
- remove vm_sw_loader pointer, and call direct_boot_sw_loader() directly.
- move get_rsdp_ptr() from vboot_wrapper.c to multiboot.c, and remove the
wrapper over two boot modes.
Tracked-On: #5197
Signed-off-by: Zide Chen <zide.chen@intel.com>
Per PCI Firmware Specification Revision 3.0, 4.1.2. MCFG Table Description:
Memory Mapped Enhanced Configuration Space Base Address Allocation Structure
assign the Start Bus Number and the End Bus Number which could decoded by the
Host Bridge. We should not access the PCI device which bus number outside of
the range of [Start Bus Number, End Bus Number).
For ACRN, we should:
1. Don't detect PCI device which bus number outside the range of
[Start Bus Number, End Bus Number) of MCFG ACPI Table.
2. Only trap the ECAM MMIO size: [MMCFG_BASE_ADDRESS, MMCFG_BASE_ADDRESS +
(End Bus Number - Start Bus Number + 1) * 0x100000) for SOS.
Tracked-On: #5233
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The ivshmem memory regions use the memory of the hypervisor and
they are continuous and page aligned.
this patch is used to initialize each memory region hpa.
v2: 1) if CONFIG_IVSHMEM_SHARED_MEMORY_ENABLED is not defined, the
entire code of ivshmem will not be compiled.
2) change ivshmem shared memory unit from byte to page to avoid
misconfiguration.
3) add ivshmem configuration and vm configuration references
v3: 1) change CONFIG_IVSHMEM_SHARED_MEMORY_ENABLED to CONFIG_IVSHMEM_ENABLED
2) remove the ivshmem configuration sample, offline tool provides default
ivshmem configuration.
3) refine code style.
v4: 1) make ivshmem_base 2M aligned.
Tracked-On: #4853
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Remove function of sanitize_vm_config() since the processing of sanitizing
will be moved to pre-build process.
When hypervisor has booted, we assume all VM configurations is sanitized;
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The commit 'HV: Config Splitlock Detection to be disable' allows
using CONFIG_ENFORCE_TURNOFF_AC to turn off splitlock #AC. If
CONFIG_ENFORCE_TURNOFF_AC is not set, splitlock #AC should be turn on
Tracked-On: #4962
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
As build variants for different board and different scenario growing, users
might make mistake on HV binary distributions. Checking board/scenario info
from log would be the fastest way to know whether the binary matches. Also
it would be of benifit to developers for confirming the correct binary they
are debugging.
Tracked-On: #4946
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
As per the BWG a delay should be provided between the
INIT IPI and Startup IPI. Without the delay observe hangs
on certain platforms during MP Init sequence. So Setting
a delay of 10us between assert INIT IPI and Startup IPI.
Also, as per SDM section 10.7 the the de-assert INIT IPI is
only used for Pentium and P6 processors. This is not applicable
for Pentium4 and Xeon processors so removing this sequence.
Tracked-On: #4835
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
CDP is an extension of CAT. It enables isolation and separate prioritization of
code and data fetches to the L2 or L3 cache in a software configurable manner,
depending on hardware support.
This commit adds a Kconfig switch "CDP_ENABLED" which depends on "RDT_ENABLED".
CDP will be enabled if the capability available and "CDP_ENABLED" is selected.
Tracked-On: #4604
Signed-off-by: Yan, Like <like.yan@intel.com>
Reviewed-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This commit makes some RDT code cleanup, mainling including:
- remove the clos_mask and mba_delay validation check in setup_res_clos_msr(), the check will be done in pre-build;
- rename platform_clos_num to valid_clos_num, which is set as the minimal clos_mas of all enabled RDT resouces;
- init the platform_clos_array in the res_cap_info[] definition;
- remove the unnecessary return values and return value check.
Tracked-On: #4604
Signed-off-by: Yan, Like <like.yan@intel.com>
#AC should be normally enabled for slpitlock detection, however,
community developers may want to run ACRN on buggy system.
In this case, CONFIG_ENFORCE_TURNOFF_AC can be used to turn off the
#AC, to let the guest run without #AC.
Tracked-On: #4765
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
If CPU support rise #AC for Splitlock Access, then enable this
feature at each CPU.
Tracked-On: #4496
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Yan, Like <like.yan@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This is a preparation patch for adding support for VT-d PI
related vCPU scheduling.
ACRN does not support vCPU migration, one vCPU always runs on
the same pCPU, so PI's ndst is never changed after startup.
VCPUs of a VM won’t share same pCPU. So the maximum possible number
of VCPUs that can run on a pCPU is CONFIG_MAX_VM_NUM.
Allocate unique Activation Notification Vectors (ANV) for each vCPU
that belongs to the same pCPU, the ANVs need only be unique within each
pCPU, not across all vCPUs. This reduces # of pre-allocated ANVs for
posted interrupts to CONFIG_MAX_VM_NUM, and enables ACRN to avoid
switching between active and wake-up vector values in the posted
interrupt descriptor on vCPU scheduling state changes.
A total of CONFIG_MAX_VM_NUM consecutive IRQs/vectors are reserved
for posted interrupts use.
The code first initializes vcpu->arch.pid.control.bits.nv dynamically
(will be added in subsequent patch), the other code shall use
vcpu->arch.pid.control.bits.nv instead of the hard-coded notification vectors.
Rename some functions:
apicv_post_intr --> apicv_trigger_pi_anv
posted_intr_notification --> handle_pi_notification
setup_posted_intr_notification --> setup_pi_notification
Tracked-On: #4506
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@Intel.com>
As ACRN prepares to support servers with large amounts of memory
current logic to allocate space for 4K pages of EPT at compile time
will increase the size of .bss section of ACRN binary.
Bootloaders could run into a situation where they cannot
find enough contiguous space to load ACRN binary under 4GB,
which is typically heavily fragmented with E820 types Reserved,
ACPI data, 32-bit PCI hole etc.
This patch does the following
1) Works only for "direct" mode of vboot
2) reserves space for 4K pages of EPT, after boot by parsing
platform E820 table, for all types of VMs.
Size comparison:
w/o patch
Size of DRAM Size of .bss
48 GB 0xe1bbc98 (~226 MB)
128 GB 0x222abc98 (~548 MB)
w/ patch
Size of DRAM Size of .bss
48 GB 0x1991c98 (~26 MB)
128 GB 0x1a81c98 (~28 MB)
Tracked-On: #4563
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The cupid() can be replaced with cupid_subleaf, which is more clear.
Having both APIs makes reading difficult.
Tracked-On: #4526
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Add some pre-assumption and safety check for PCIe ECAM:
1) ACRN only support platforms with PCIe ECAM to access PCIe device CFG space;
2) Must not use ECAM to access PCIe device CFG space before
pci_switch_to_mmio_cfg_ops was called. (In release version, ACRN didn't support
IO port Mechanism. ECAM is the only way to access the PCIe device CFG space).
Tracked-On: #4371
Signed-off-by: Li Fei1 <fei1.li@intel.com>
is not set
This patch does the following,
1. Removes RDT code if CONFIG_RDT_ENABLED flag is
not set.
2. Set the CONFIG_RDT_ENABLED flag only on platforms
that support RDT so that build scripts will automatically
reflect the config.
Tracked-On: #3715
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
cache configuration.
This patch creates a generic infrastructure for
RDT resources instead of just L2 or L3 cache. This
patch also fixes L3 CAT config overwrite by L2 in
cases where both L2 and L3 CAT are supported.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
As part of rdt cat refactoring, goal is to combine all rdt
specific features such as CAT under one module. So renaming
rdt resouce specific files such as cat.c/.h to generic rdt.c/.h
files.
Tracked-On: #3715
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Initialize and sanitize a acrn specific multiboot info struct with current
supported multiboot1 in very early boot stage, which would bring below
benifits:
- don't need to do hpa2hva convention every time when refering boot_regs;
- panic early if failed to sanitize multiboot info, so that don't need to
check multiboot info pointer/flags and panic in later boot process;
- keep most code unchanged when introduce multiboot2 support in future;
Tracked-On: #4419
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1. Rename BOOT_CPU_ID to BSP_CPU_ID
2. Repace hardcoded value with BSP_CPU_ID when
ID of BSP is referenced.
Tracked-On: #4420
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
In platforms that support CAT, when it is enabled by ACRN, i.e.
IA32_resourceType_MASK_n registers are programmed with customized values,
it has impacts to the whole system.
The per guest flag GUEST_FLAG_CLOS_REQUIRED suggests that CAT may be
enabled in some guests, but not in others who don't have this flag,
which is conceptually incorrect.
This patch removes GUEST_FLAG_CLOS_REQUIRED, and adds a new Kconfig
entry CAT_ENABLED for CAT enabling. When it's enabled, platform_clos_array[]
defines a set of system-wide Class of Service (COS, or CLOS), and the
per guest vm_configs[].clos associates the guest with particular CLOS.
Tracked-On: #2462
Signed-off-by: Zide Chen <zide.chen@intel.com>
Currently panic() and pr_xxx() statements before init_primary_pcpu_post()
won't be printed, which is inconvenient and misleading for debugging.
This patch makes pr_xxx() APIs working before init_pcpu_pre():
- clear .bss in init.c, which makes sense to clear .bss at the very beginning
of initialization code. Also this makes it possible to call init_logmsg()
before init_pcpu_pre().
- move parse_hv_cmdline() and uart16550_init(true) to init.c.
- refine ticks_to_us() to handle the case that it's called before
calibrate_tsc(). As a side effect, it prints "0us" in early pr_xxx() calls.
- call init_debug_pre() in init_primary_pcpu() and after this point,
both printf() and pr_xxx() APIs are available.
However, this patch doesn't address the issue that pr_xxx() could be called
on PCPUs that set_current_pcpu_id() hasn't been called, which implies that
the PCPU ID shown in early logs may not be accurate.
Tracked-On: #2987
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1. Align the coding style for these MACROs
2. Align the values of fixed VECTORs
Tracked-On: #4348
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
SOS will use PCIe ECAM access PCIe external configuration space. HV should trap this
access for security(Now pre-launched VM doesn't want to support PCI ECAM; post-launched
VM trap PCIe ECAM access in DM).
Besides, update PCIe MMCONFIG region to be owned by hypervisor and expose and pass through
platform hide PCI devices by BIOS to SOS.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Use Enhanced Configuration Access Mechanism (MMIO) instead of PCI-compatible
Configuration Mechanism (IO port) to access PCIe Configuration Space
PCI-compatible Configuration Mechanism (IO port) access is used for UART in
debug version.
Tracked-On: #3475
Signed-off-by: Li Fei1 <fei1.li@intel.com>
rename the macro since MAX_PCPU_NUM could be parsed from board file and
it is not a configurable item anymore.
Tracked-On: #4230
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The default PCI mmcfg base is stored in ACPI MCFG table, when
CONFIG_ACPI_PARSE_ENABLED is set, acpi_fixup() function will
parse and fix up the platform mmcfg base in ACRN boot stage;
when it is not set, platform mmcfg base will be initialized to
DEFAULT_PCI_MMCFG_BASE which generated by acrn-config tool;
Please note we will not support platform which has multiple PCI
segment groups.
Tracked-On: #4157
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
xsave area:
legacy region: 512 bytes
xsave header: 64 bytes
extended region: < 3k bytes
So, pre-allocate 4k area for xsave. Use certain instruction to save or
restore the area according to hardware xsave feature set.
Tracked-On: #4166
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Anthony Xu <anthony.xu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In later patches we use information from DMAR tables to guide discovery
and initialization of PCI devices.
Tracked-On: #4134
Signed-off-by: Alexander Merritt <alex.merritt@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
