Per PCI Firmware Specification Revision 3.0, 4.1.2. MCFG Table Description:
Memory Mapped Enhanced Configuration Space Base Address Allocation Structure
assign the Start Bus Number and the End Bus Number which could decoded by the
Host Bridge. We should not access the PCI device which bus number outside of
the range of [Start Bus Number, End Bus Number).
For ACRN, we should:
1. Don't detect PCI device which bus number outside the range of
[Start Bus Number, End Bus Number) of MCFG ACPI Table.
2. Only trap the ECAM MMIO size: [MMCFG_BASE_ADDRESS, MMCFG_BASE_ADDRESS +
(End Bus Number - Start Bus Number + 1) * 0x100000) for SOS.
Tracked-On: #5233
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The old method of build pre-launched VM vacpi by HV source code is deprecated,
so remove related source code;
Tracked-On: #5266
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously we use a pre-defined structure as vACPI table for pre-launched
VM, the structure is initialized by HV code. Now change the method to use a
pre-loaded multiboot module instead. The module file will be generated by
acrn-config tool and loaded to GPA 0x7ff00000, a hardcoded RSDP table at
GPA 0x000f2400 will point to the XSDT table which at GPA 0x7ff00080;
Tracked-On: #5266
Signed-off-by: Victor Sun <victor.sun@intel.com>
Signed-off-by: Shuang Zheng <shuang.zheng@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously the ACPI table was stored in F segment which might not be big
enough for a customized ACPI table, hence reserve 1MB space in pre-launched
VM e820 table to store the ACPI related data:
0x7ff00000 ~ 0x7ffeffff : ACPI Reclaim memory
0x7fff0000 ~ 0x7fffffff : ACPI NVS memory
Tracked-On: #5266
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously the min load_addr for HV image is hard coded to 0x10000000 when
CONFIG_RELOC is enabled, now use CONFIG_HV_RAM_START as its prefer minimum
address like setting of CONFIG_PHYSICAL_START do in Linux kernel.
With this patch, we can offload the CONFIG_HV_RAM_START algorithm to
acrn-config or manually set it in scenario XML on some special boards.
Tracked-On: #5275
Signed-off-by: Victor Sun <victor.sun@intel.com>
When HV pass through the P2SB MMIO device to pre-launched VM, vgpio
device model traps MMIO access to the GPIO registers within P2SB so
that it can expose virtual IOAPIC pins to the VM in accordance with
the programmed mappings between gsi and vgsi.
Tracked-On: #5246
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add the capability of forwarding specified physical IOAPIC interrupt
lines to pre-launched VMs as virtual IOAPIC interrupts. This is for the
sake of the certain MMIO pass-thru devices on EHL CRB which can support
only INTx interrupts.
Tracked-On: #5245
Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
BDF string can be parsed by the configuration tool. A 16bit WORD value with
format (B:8, D:5, F:3) can be passed from configuration to the
hypervisor directly to save some BDF string parse code.
Tracked-On: #4937
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When trying to passthru a DHRD-ignored PCI device,
iommu_attach_device shall report success. Otherwise,
the assign_vdev_pt_iommu_domain will result in HV panic.
Same for iommu_detach_device case.
Tracked-On: #5240
Signed-off-by: Stanley Chang <stanley.chang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add HC_CREATE_VDEV and HC_DESTROY_VDEV two hypercalls that are used to
create and destroy an emulated device(PCI device or legacy device) in hypervisor
v3: 1) change HC_CREATE_DEVICE and HC_DESTROY_DEVICE to HC_CREATE_VDEV
and HC_DESTROY_VDEV
2) refine code style
v4: 1) remove unnecessary parameter
2) add VM state check for HC_CREATE_VDEV and HC_DESTROY hypercalls
Tracked-On: #4853
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
1.Modify clos_mask and mba_delay as a member of the union type.
2.Move HV_SUPPORTED_MAX_CLOS ,MAX_CACHE_CLOS_NUM_ENTRIES and
MAX_MBA_CLOS_NUM_ENTRIES to misc_cfg.h file.
Tracked-On: #5229
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
HV_SUPPORTED_MAX_CLOS:
This value represents the maximum CLOS that is allowed by ACRN hypervisor.
This value is set to be least common Max CLOS (CPUID.(EAX=0x10,ECX=ResID):EDX[15:0])
among all supported RDT resources in the platform. In other words, it is
min(maximum CLOS of L2, L3 and MBA). This is done in order to have consistent
CLOS allocations between all the RDT resources.
Tracked-On: #5229
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
New board, EHL CRB, does not have legacy port IO UART. Even the PCI UART
are not work due to BIOS's bug workaround(the BARs on LPSS PCI are reset
after BIOS hand over control to OS). For ACRN console usage, expose the
debug UART via ACPI PnP device (access by MMIO) and add support in
hypervisor debug code.
Another special thing is that register width of UART of EHL CRB is
1byte. Introduce reg_width for each struct console_uart.
Tracked-On: #4937
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
-- use an array to fast locate the hypercall handler
to replace switch case.
-- uniform hypercall handler as below:
int32_t (*handler)(sos_vm, target_vm, param1, param2)
Tracked-On: #4958
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Enhance the help text that accompanies the CONFIG_SCENARIO symbol in Kconfig
Tracked-On: #5203
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
The ivshmem memory regions use the memory of the hypervisor and
they are continuous and page aligned.
this patch is used to initialize each memory region hpa.
v2: 1) if CONFIG_IVSHMEM_SHARED_MEMORY_ENABLED is not defined, the
entire code of ivshmem will not be compiled.
2) change ivshmem shared memory unit from byte to page to avoid
misconfiguration.
3) add ivshmem configuration and vm configuration references
v3: 1) change CONFIG_IVSHMEM_SHARED_MEMORY_ENABLED to CONFIG_IVSHMEM_ENABLED
2) remove the ivshmem configuration sample, offline tool provides default
ivshmem configuration.
3) refine code style.
v4: 1) make ivshmem_base 2M aligned.
Tracked-On: #4853
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Fix the bug for "is_apl_platform" func.
"monitor_cap_buggy" is identical to "is_apl_platform", so remove it.
On apl platform:
1) ACRN doesn't use monitor/mwait instructions
2) ACRN disable GPU IOMMU
Tracked-On:#3675
Signed-off-by: Junming Liu <junming.liu@intel.com>
v3 -> v4:
Refine commit message and code stype
1.
SDM Vol. 2A 3-211 states DisplayFamily = Extended_Family_ID + Family_ID
when Family_ID == 0FH.
So it should be family += ((eax >> 20U) & 0xffU) when Family_ID == 0FH.
2.
IF (Family_ID = 06H or Family_ID = 0FH)
THEN DisplayModel = (Extended_Model_ID « 4) + Model_ID;
While previous code this logic:
IF (DisplayFamily = 06H or DisplayFamily = 0FH)
Fix the bug about calculation of display family and
display model according to SDM definition.
3. use variable name to distinguish Family ID/Display Family/Model ID/Display Model,
then the code is more clear to avoid some mistake
Tracked-On:#3675
Signed-off-by: liujunming <junming.liu@intel.com>
Reviewed-by: Wu Xiangyang <xiangyang.wu@linux.intel.com>
Acked-by： Eddie Dong <eddie.dong@intel.com>
This patch will move the VM configuration check to pre-build stage,
a test program will do the check for pre-defined VM configuration
data before making hypervisor binary. If test failed, the make
process will be aborted. So once the hypervisor binary is built
successfully or start to run, it means the VM configuration has
been sanitized.
The patch did not add any new VM configuration check function,
it just port the original sanitize_vm_config() function from cpu.c
to static_checks.c with below change:
1. remove runtime rdt detection for clos check;
2. replace pr_err() from logmsg.h with printf() from stdio.h;
3. replace runtime call get_pcpu_nums() in ALL_CPUS_MASK macro
with static defined MAX_PCPU_NUM;
4. remove cpu_affinity check since pre-launched VM might share
pcpu with SOS VM;
The BOARD/SCENARIO parameter check and configuration folder check is
also moved to prebuild Makefile.
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Remove function of sanitize_vm_config() since the processing of sanitizing
will be moved to pre-build process.
When hypervisor has booted, we assume all VM configurations is sanitized;
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
-- move vm_state_lock to other place in vm structure
to avoid the memory waste because of the page-aligned.
-- remove the memset from create_vm
-- explicitly set max_emul_mmio_regions and vcpuid_entry_nr to 0
inside create_vm to avoid use without initialization.
-- rename max_emul_mmio_regions to nr_emul_mmio_regions
v1->v2:
add deinit_emul_io in shutdown_vm
Tracked-On: #4958
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
Reviewed-by: Grandhi, Sainath <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously the CPU affinity of SOS VM is initialized at runtime during
sanitize_vm_config() stage, follow the policy that all physical CPUs
except ocuppied by Pre-launched VMs are all belong to SOS_VM. Now change
the process that SOS CPU affinity should be initialized at build time
and has the assumption that its validity is guarenteed before runtime.
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously we have complicated check mechanism on platform_acpi_info.h which
is supposed to be generated by acrn-config tool, but given the reality that
all configurations should be generated by acrn-config before build acrn
hypervisor, this check is not needed anymore.
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The SDC scenario configurations will not be validated so remove it from
build makefile;
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The old layout configuration source which located in:
hypervisor/arch/x86/configs/ is abandoned, remove it;
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
The make command is same as old configs layout:
under acrn-hypervisor folder:
make hypervisor BOARD=xxx SCENARIO=xxx [TARGET_DIR]=xxx [RELEASE=x]
under hypervisor folder:
make BOARD=xxx SCENARIO=xxx [TARGET_DIR]=xxx [RELEASE=x]
if BOARD/SCENARIO parameter is not specified, the default will be:
BOARD=nuc7i7dnb SCENARIO=industry
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There are 3 kinds of configurations in ACRN hypervisor source code: hypervisor
overall setting, per-board setting and scenario specific per-VM setting.
Currently Kconfig act as hypervisor overall setting and its souce is located at
"hypervisor/arch/x86/configs/$(BOARD).config"; Per-board configs are located at
"hypervisor/arch/x86/configs/$(BOARD)" folder; scenario specific per-VM configs
are located at "hypervisor/scenarios/$(SCENARIO)" folder.
This layout brings issues that board configs and VM configs are coupled tightly.
The board specific Kconfig file and misc_cfg.h are shared by all scenarios, and
scenario specific pci_dev.c is shared by all boards. So the user have no way to
build hypervisor binary for different scenario on different board with one
source code repo.
The patch will setup a new VM configurations layout as below:
misc/vm_configs
├── boards --> folder of supported boards
│ ├── <board_1> --> scenario-irrelevant board configs
│ │ ├── board.c --> C file of board configs
│ │ ├── board_info.h --> H file of board info
│ │ ├── pci_devices.h --> pBDF of PCI devices
│ │ └── platform_acpi_info.h --> native ACPI info
│ ├── <board_2>
│ ├── <board_3>
│ └── <board...>
└── scenarios --> folder of supported scenarios
├── <scenario_1> --> scenario specific VM configs
│ ├── <board_1> --> board specific VM configs for <scenario_1>
│ │ ├── <board_1>.config --> Kconfig for specific scenario on specific board
│ │ ├── misc_cfg.h --> H file of board specific VM configs
│ │ ├── pci_dev.c --> board specific VM pci devices list
│ │ └── vbar_base.h --> vBAR base info of VM PT pci devices
│ ├── <board_2>
│ ├── <board_3>
│ ├── <board...>
│ ├── vm_configurations.c --> C file of scenario specific VM configs
│ └── vm_configurations.h --> H file of scenario specific VM configs
├── <scenario_2>
├── <scenario_3>
└── <scenario...>
The new layout would decouple board configs and VM configs completely:
The boards folder stores kinds of supported boards info, each board folder
stores scenario-irrelevant board configs only, which could be totally got from
a physical platform and works for all scenarios;
The scenarios folder stores VM configs of kinds of working scenario. In each
scenario folder, besides the generic scenario specific VM configs, the board
specific VM configs would be put in a embedded board folder.
In new layout, all configs files will be removed out of hypervisor folder and
moved to a separate folder. This would make hypervisor LoC calculation more
precisely with below fomula:
typical LoC = Loc(hypervisor) + Loc(one vm_configs)
which
Loc(one vm_configs) = Loc(misc/vm_configs/boards/<board>)
+ LoC(misc/vm_configs/scenarios/<scenario>/<board>)
+ Loc(misc/vm_configs/scenarios/<scenario>/vm_configurations.c
+ Loc(misc/vm_configs/scenarios/<scenario>/vm_configurations.h
Tracked-On: #5077
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
To hide CET feature from guest VM completely, the MSR IA32_MSR_XSS also
need to be intercepted because it comprises CET_U and CET_S feature bits
of xsave/xstors operations. Mask these two bits in IA32_MSR_XSS writing.
With IA32_MSR_XSS interception, member 'xss' of 'struct ext_context' can
be removed because it is duplicated with the MSR store array
'vcpu->arch.guest_msrs[]'.
Tracked-On: #5074
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Return-oriented programming (ROP), and similarly CALL/JMP-oriented
programming (COP/JOP), have been the prevalent attack methodologies for
stealth exploit writers targeting vulnerabilities in programs.
CET (Control-flow Enforcement Technology) provides the following
capabilities to defend against ROP/COP/JOP style control-flow subversion
attacks:
* Shadow stack: Return address protection to defend against ROP.
* Indirect branch tracking: Free branch protection to defend against
COP/JOP
The full support of CET for Linux kernel has not been merged yet. As the
first stage, hide CET from guest VM.
Tracked-On: #5074
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
On WHL platform, we need to pass through TPM to Secure pre-launched VM. In order
to do this, we need to add TPM2 ACPI Table and add TPM DSDT ACPI table to include
the _CRS.
Now we only support the TPM 2.0 device (TPM 1.2 device is not support). Besides,
the TPM must use Start Method 7 (Uses the Command Response Buffer Interface)
to notify the TPM 2.0 device that a command is available for processing.
Tracked-On: #5053
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Using ACPI_TABLE_HEADER MACRO to initial the ACPI Table Header.
Tracked-On: #5053
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
Add mmio device pass through support for pre-launched VM.
When we pass through a MMIO device to pre-launched VM, we would remove its
resource from the SOS. Now these resources only include the MMIO regions.
Tracked-On: #5053
Acked-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Add two hypercalls to support MMIO device pass through for post-launched VM.
And when we support MMIO pass through for pre-launched VM, we could re-use
the code in mmio_dev.c
Tracked-On: #5053
Signed-off-by: Li Fei1 <fei1.li@intel.com>
During context switch in hypervisor, xsave/xrstore are used to
save/resotre the XSAVE area according to the XCR0 and XSS. The legacy
region in XSAVE area include FPU and SSE, we should make sure the
legacy region be saved during contex switch. FPU in XCR0 is always
enabled according to SDM.
For SSE, we enable it in XCR0 during context switch.
Tracked-On: #5062
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
kick_thread function is only used by kick_vcpu to kick vcpu out of
non-root mode, the implementation in it is sending IPI to target CPU if
target obj is running and target PCPU is not current one; while for
runnable obj, it will just make reschedule request. So the kick_thread
is not actually belong to scheduler module, we can drop it and just do
the cpu notification in kick_vcpu.
Tracked-On: #5057
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
vcpu->running is duplicated with THREAD_STS_RUNNING status of thread
object. Introduce an API sleep_thread_sync(), which can utilize the
inner status of thread object, to do the sync sleep for zombie_vcpu().
Tracked-On: #5057
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Reviewed-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
-- replace global hypercall lock with per-vm lock
-- add spinlock protection for vm & vcpu state change
v1-->v2:
change get_vm_lock/put_vm_lock parameter from vm_id to vm
move lock obtain before vm state check
move all lock from vmcall.c to hypercall.c
Tracked-On: #4958
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There are some devices (like Samsung NVMe SSD SM981/PM981 which has 33 MSIX tables)
which have more than 16 MSIX tables. Extend the default value to 64 to handle them.
Tracked-On: #4994
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Some OSes assume the platform must have the IOAPIC. For example:
Linux Kernel allocates IRQ force from GSI (0 if there's no PIC and IOAPIC) on x86.
And it thinks IRQ 0 is an architecture special IRQ, not for device driver. As a
result, the device driver may goes wrong if the allocated IRQ is 0 for RTVM.
This patch expose vIOAPIC to RTVM with LAPIC passthru even though the RTVM can't
use IOAPIC, it servers as a place holder to fullfil the guest assumption.
After vIOAPIC has exposed to guest unconditionally, the 'ready' field could be
removed since we do vIOAPIC initialization for each guest.
Tracked-On: #4691
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
will follow this convention for spin lock initialization:
-- for simple global variable locks, use this style:
static spinlock_t xxx_spinlock = {.head = 0U, .tail = 0U,}
-- for the locks inside a data structure, need to call
spinlock_init to initialize.
Tracked-On: #4958
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
According to SDM 10.12.11, we can know this register is dedicated to the
purpose of sending self-IPIs with the intent of enabling a highly
optimized path for sending self-IPIs. Also sending the IPI via the Self
Interrupt Register ensures that interrupt is delivered to the processor
core. Specifically completion of the WRMSR instruction to the SELF IPI
register implies that the interrupt has been logged into the IRR.
Tracked-On: #4937
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by： Eddie Dong <eddie.dong@intel.com>
Currently, not all platforms support posted interrupt processing of both
VT-x and VT-d. On EHL, VT-d doesn't support posted interrupt processing.
So in such scenario, is_pi_capable() in vcpu_handle_pi_notification()
will bypass the PIR pending bits check which might cause a self-NV-IPI
lost.
With commit "bf1ff8c98 (hv: Offload syncing PIR to vIRR to processor
hardware)", the syncing PIR to vIRR is postponed and it is handled by a
self-NV-IPI in the following VMEnter. The process looks like,
a) vcpu A accepts a virtual interrupt ->
1) ACRN_REQUEST_EVENT is set
2) corresponding bit in PIR is set
3) Posted Interrupt ON bit is set
b) vcpu A does virtual interrupt injection on resume path due to
the pending ACRN_REQUEST_EVENT ->
1) hypervisor disables host interrupt
2) ACRN_REQUEST_EVENT is cleared
3) a self-NV-IPI is sent via ICR of LAPIC.
4) IRR bit of the self-NV-IPI is set
c) (VM-ENTRY) vcpu A returns into non-root mode
1) host interrupt enable(by HW)
2) posted interrupt processing clears the ON bit, sync PIR to vIRR
3) deliver the virtual interrupt if guest rflags.IF=1
d) (VM-EXIT) vcpu A traps due to a instruction execution (e.g. HLT)
1) host interrupt disable(by HW)
2) hypervisor enable host interrupt
Above illustrates a normal process of the virtual interrupt injection
with cpu PI support. However, a failing case is observed. The failing
case is that the self-NV-IPI from b-3 is not accepted by the core until
a timing between d-1 and d-2. b-4 happening between d-1 and d-2 is
observed by debug trace. So the self-NV-IPI will be handled in root-mode
which cannot do the syncing PIR to vIRR processing. Due to the bug
described in the first paragraph, vcpu_handle_pi_notification() cannot
succeed the virtual interrupt injection request. This patch fix it by
removing the wrong check in vcpu_handle_pi_notification() because
vcpu_handle_pi_notification() only happens on platform with cpu PI
support.
Here are some cost data for sending IPI via LAPIC ICR regsiter.
Normally, the cycles between ICR write and IRR got set is 140~260,
which is not accurate due to the MSR read overhead.
And from b-3 to c is about 560 cycles. So b-4 happens during this
period. But in bad case, b-4 doesn't happen even c is triggered.
The worse case i captured is that ICR write and IRR got set costs more
than 1900 cycles. Now, the best GUESS of the huge cost of IPI via ICR is
the ACPI bus arbitration(refer to SDM 10.6.3, 10.7 and Figure 10-17).
Tracked-On: #4937
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by： Eddie Dong <eddie.dong@intel.com>
Wrap a function to do guest ept flush. This function doesn't do real EPT flush.
It just make the EPT flush request and do the real flush just before vcpu vmenter.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
remove spin lock for micro code update since the guest
operating system will take lock
Tracked-On: #4958
Signed-off-by: Mingqiang Chi <mingqiang.chi@intel.com>
The commit 'HV: Config Splitlock Detection to be disable' allows
using CONFIG_ENFORCE_TURNOFF_AC to turn off splitlock #AC. If
CONFIG_ENFORCE_TURNOFF_AC is not set, splitlock #AC should be turn on
Tracked-On: #4962
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Check bit 48 in IA32_VMX_BASIC MSR, if it is 1, return error, as we only
support Intel 64 architecture.
SDM:
Appendix A.1 BASIC VMX INFORMATION
Bit 48 indicates the width of the physical addresses that may be used for the
VMXON region, each VMCS, anddata structures referenced by pointers in a
VMCS (I/O bitmaps, virtual-APIC page, MSR areas for VMX transitions). If
the bit is 0, these addresses are limited to the processor’s
physical-address width.2 If the bit is 1, these addresses are limited to
32 bits. This bit is always 0 for processors that support Intel 64
architecture.
Tracked-On: #4956
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
We always assume the physical platform has XSAVE, and we always enable
XSAVE at the beginning, so, no need to check the OXSAVE in host.
Tracked-On: #4956
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
As build variants for different board and different scenario growing, users
might make mistake on HV binary distributions. Checking board/scenario info
from log would be the fastest way to know whether the binary matches. Also
it would be of benifit to developers for confirming the correct binary they
are debugging.
Tracked-On: #4946
Signed-off-by: Victor Sun <victor.sun@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
dmar_reserve_irte is added to reserve N coutinuous IRTEs.
N could be 1, 2, 4, 8, 16, or 32.
The reserved IRTEs will not be freed.
Tracked-On:#4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
For a ptirq_remapping_info entry, when build IRTE:
- If the caller provides a valid IRTE, use the IRET
- If the caller doesn't provide a valid IRTE, allocate a IRET when the
entry doesn't have a valid IRTE, in this case, the IRET will be freed
when free the entry.
Tracked-On:#4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
idx_in:
- If the caller of dmar_assign_irte passes a valid IRTE index, it will
be resued;
- If the caller of dmar_assign_irte passes INVALID_IRTE_ID as IRTE index,
the function will allocate a new IRTE.
idx_out:
This paramter return the actual index of IRTE used. The caller need to
check whether the return value is valid or not.
Also this patch adds an internal function alloc_irte.
The function takes count as input paramter to allocate continuous IRTEs.
The count can only be 1, 2, 4, 8, 16 or 32.
This is prepared for multiple MSI vector support.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Script only append 'U' for the config of int with a range.
Add a range to MAX_IR_ENTRIES.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
There're some platforms still doesn't support 1GB large page on CPU side.
Such as lakefield, TNT and EHL platforms on which have some silicon bug and
this case CPU don't support 1GB large page.
This patch tries to release this constrain to support more hardware platform.
Note this patch doesn't release the constrain on IOMMU side.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
This patch tries to release hardware platform 1GB large page support constrain
on CPU side.
There're some silicon bug on lakefield, TNT and EHL platforms which cause CPU
couldn't support 1GB large page. As a result, the pre-assumption The platform
which ACRN supports must support 1GB large page on both CPU side and VTD side
is not true any more.
This reverts commit f01aad7e to let trampoline execution use 2MB pages.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
The information needed to enable MSI-x emulation.
Only enable MSI-x emuation for the devices in msix_emul_devs array.
Currently, only EHL has the need to enable MSI-x emulation for TSN
devices.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously append_seed_arg() just do fill in seed arg to dest cmd buffer,
so rename the api name to fill_seed_arg().
Since fill_seed_arg() will be called in SOS VM path only, the param of
bool vm_is_sos is not needed and will be replaced by dest buffer size.
The seed_args[] which used by fill_seed_arg() is pre-defined as all-zero,
so memset() is not needed in fill_seed_arg(), buffer pointer check
and strncpy_s() are not needed also.
Tracked-On: #4885
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Per C11 standard (ISO/IEC 9899:2011): K.3.7.1.1
1. Copying shall not take place between objects that overlap;
2. If there is a runtime-constraint violation, the memcpy_s function stores
zeros in the first s1max characters of the object;
3. The memcpy_s function returns zero if there was no runtime-constraint
violation. Otherwise, a nonzero value is returned.
Tracked-On: #4885
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Previously sanitize_multiboot_info() was called after init_debug_pre() because
the debug message can only print after uart is initialized. On the other hand,
multiboot cmdline need to be parsed before init_debug_pre() because the cmdline
could override uart settings and make sure debug message printed successfully.
This cause multiboot info was parsed in two stages.
The patch revise the multiboot parse logic that split sanitize_multiboot_info()
api and use init_acrn_multiboot_info() api for the early stage. The most of
multiboot info will be initialized during this stage and no debug message need
to be printed. After uart is initialized, the sanitize_multiboot_info() would
do sanitize multiboot info and print needed debug messages.
Tracked-On: #4885
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Update efi bootloader image file path for Yocto rootfs in Kconfig.
Tracked-On: #4868
Signed-off-by: Wei Liu <weix.w.liu@intel.com>
Reviewed-by: Victor Sun <victor.sun@intel.com>
Now Host Bridge and PCI Bridge could only be added to SOS's acrn_vm_pci_dev_config.
So For UOS, we always emualte Host Bridge and PCI Bridge for it and assign PCI device
to it; for SOS, if it's the highest severity VM, we will assign Host Bridge and PCI
Bridge to it directly, otherwise, we will emulate them same as UOS.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
According PCI Code and ID Assignment Specification Revision 1.11, a PCI device
whose Base Class is 06h and Sub-Class is 00h is a Host bridge.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
We should check whether a PCI device is host bridge or not by Base Class (06h)
and Sub-Class (00h).
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
As per the BWG a delay should be provided between the
INIT IPI and Startup IPI. Without the delay observe hangs
on certain platforms during MP Init sequence. So Setting
a delay of 10us between assert INIT IPI and Startup IPI.
Also, as per SDM section 10.7 the the de-assert INIT IPI is
only used for Pentium and P6 processors. This is not applicable
for Pentium4 and Xeon processors so removing this sequence.
Tracked-On: #4835
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
in shutdown_vm, it uses guest flags when handling the phyiscal
CPUs whose LAPIC is pass-through. So if it is cleared first,
the related vCPUs and pCPUs can not be switched to correct state.
so move the clear action after the flags used.
Tracked-On: #4848
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
1. context_entry couldn't be NULL in iommu_attach_device since bus
number is checked before the call.
2. root_entry couldn't be NULL in iommu_detach_device since bus number
is checked before the call.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add a function dmar_unit_valid to check if the input dmar uint is valid
or not.
A valid dmar_unit should not be NULL, or ignore flag should not be set.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Snoop control will not be turned on by hypervisor, delete snoop control
related code.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Initialize root_table_addr/ir_table_addr of dmar uint when register the dmar uint.
So no need to check if they are initialzed or not later.
Tracked-On: #4831
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Invalidate cache by scanning and flushing the whole guest memory is
inefficient which might cause long execution time for WBINVD emulation.
A long execution in hypervisor might cause a vCPU stuck phenomenon what
impact Windows Guest booting.
This patch introduce a workaround method that pausing all other vCPUs in
the same VM when do wbinvd emulation.
Tracked-On: #4703
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Refine find_ptirq_entry by hashing instead of walk each of the PTIRQ entries one by one.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong<eddie.dong@Intel.com>
RTVM (with lapic PT) boots hang when maxcpus is
assigned a value less than the CPU number configured
in hypervisor.
In this case, vlapic_state(per VM) is left in TRANSITION
state after BSP boot, which blocks interupts to be injected
to this UOS.
Tracked-On: #4803
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Li, Fei <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
There's no need to look up MSI ptirq entry by virtual SID any more since the MSI
ptirq entry would be removed before the device is assigned to a VM.
Now the logic of MSI interrupt remap could simplify as:
1. Add the MSI interrupt remap first;
2. If step is already done, just do the remap part.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong<eddie.dong@Intel.com>
Reviewed-by: Grandhi, Sainath <sainath.grandhi@intel.com>
If HV relocation is enabled, either ACRN efi-stub or GRUB relocates
hypervisor image above HPA 256MB, thus we put hvlog and ramoops buffer
under 256MB to avoid conflict with hypervisor owned address.
This patch hardcodes these addresses:
0xa00000 - 0xdfffff: 4MiB for ramoops buffer
0xe00000 - 0xffffff: 2MiB for hvlog buffer
However, user can customize them to other addresses as long as it's under
256MB, available in host e820, and SOS bootarg "nokaslr" is not specified.
If HV relocation is disabled, need to make sure that these buffer
addresses are not between HV_RAM_START and HV_RAM_START + HV_RAM_SIZE.
Tracked-On: #4760
Signed-off-by: Zide Chen <zide.chen@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
For post-launched VMs, the configured CPU affinity could be different
from the actual running CPU affinity. This new field acrn_vm->cpu_affinity
recognizes this difference so that it's possible that CREATE_VM
hypercall won't overwrite the configured CPU afifnity.
Change name cpu_affinity_bitmap in acrn_vm_config to cpu_affinity.
This is read-only in run time, never overwritten by acrn-dm.
Remove vm_config->vcpu_num, which means the number of vCPUs of the
configured CPU affinity. This is not to be confused with the actual
running vCPU number: vm->hw.created_vcpus.
Changed get_vm_bsp_pcpu_id() to get_configured_bsp_pcpu_id() for less
confusion.
Tracked-On: #4616
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
ACRN syncs PIR to vIRR in the software in cases the Posted
Interrupt notification happens while the pCPU is in root mode.
Sync can be achieved by processor hardware by sending a
posted interrupt notiification vector.
This patch sends a self-IPI, if there are interrupts pending in PIR,
which is serviced by the logical processor at the next
VMEnter
Tracked-On: #4777
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
CDP is an extension of CAT. It enables isolation and separate prioritization of
code and data fetches to the L2 or L3 cache in a software configurable manner,
depending on hardware support.
This commit adds a Kconfig switch "CDP_ENABLED" which depends on "RDT_ENABLED".
CDP will be enabled if the capability available and "CDP_ENABLED" is selected.
Tracked-On: #4604
Signed-off-by: Yan, Like <like.yan@intel.com>
Reviewed-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This commit makes some RDT code cleanup, mainling including:
- remove the clos_mask and mba_delay validation check in setup_res_clos_msr(), the check will be done in pre-build;
- rename platform_clos_num to valid_clos_num, which is set as the minimal clos_mas of all enabled RDT resouces;
- init the platform_clos_array in the res_cap_info[] definition;
- remove the unnecessary return values and return value check.
Tracked-On: #4604
Signed-off-by: Yan, Like <like.yan@intel.com>
A RDT resource could be CAT or MBA, so only one of struct rdt_cache and struct rdt_membw
would be used at a time. They should be a union.
This commit merge struct rdt_cache and struct rdt_membw in to a union res.
Tracked-On: #4604
Signed-off-by: Yan, Like <like.yan@intel.com>
Reviewed-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com
#AC should be normally enabled for slpitlock detection, however,
community developers may want to run ACRN on buggy system.
In this case, CONFIG_ENFORCE_TURNOFF_AC can be used to turn off the
#AC, to let the guest run without #AC.
Tracked-On: #4765
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The virtual MSI information could be included in ptirq_remapping_info structrue,
there's no need to pass another input paramater for this puepose. So we could
remove the ptirq_msi_info input.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
We look up PTIRQ entru only by SID. So _by_sid could removed.
And refine function name to verb-obj style.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
For return value of local_gpa2hpa, either INVALID_HPA or NULL
means the EPT walking failure. Current code only take care of
NULL return and leave INVALID_HPA as correct case.
In some cases (if guest page table is filled with invalid memory
address), it could crash ACRN from guest.
Add INVALID_HPA return check as well.
Also add @pre assumptions for some gpa2hpa usages.
Tracked-On: #4730
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
When boot ACRN hypervisor from grub multiboot, HV will be loaded at
CONFIG_HV_RAM_START since relocation is not supported in grub
multiboot1. The CONFIG_HV_RAM_SIZE in industry scenario will take
~330MB(0x14000000), unfortunately the efi memmap on NUC7i7DNB is
truncated at 0x6dba2000 although it is still usable from 0x6dba2000. So
from grub point of view, it could not find a continuous memory from
0x6000000 to load industry scenario. Per efi memmap, there is a big
memory area available from 0x40400000, so put CONFIG_HV_RAM_START to
0x41000000 is much safe for NUC7i7DNB.
Tracked-On: #4641
Signed-off-by: Victor Sun <victor.sun@intel.com>
The original stack used in CPU booting is: ld_bss_end + 4KB;
which could be out of the RAM size limit defined in link_ram file.
So add a specific stack space in link_ram file, and used in
CPU booting.
Tracked-On: #4738
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Reviewed by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
According to SDM Vol 3, Chap 10.4.7.2 Local APIC State After It Has Been Software Disabled,
The mask bits for all the LVT entries are set when the local APIC has been software disabled.
So there's no need to mask all the LVT entries one by one.
Tracked-On: #4550
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Currently the vcpu_affinity[] array fixes the vCPU to pCPU mapping.
While the new cpu_affinity_bitmap doesn't explicitly sepcify this
mapping, instead, it implicitly assumes that vCPU0 maps to the pCPU
with lowest pCPU ID, vCPU1 maps to the second lowest pCPU ID, and
so on.
This makes it possible for post-launched VM to run vCPUs on a subset of
these pCPUs only, and not all of them.
acrn-dm may launch post-launched VMs with the current approach: indicate
VM UUID and hypervisor launches all VCPUs from the PCPUs that are masked
in cpu_affinity_bitmap.
Also acrn-dm can choose to launch the VM on a subset of PCPUs that is
defined in cpu_affinity_bitmap. In this way, acrn-dm must specify the
subset of PCPUs in the CREATE_VM hypercall.
Additionally, with this change, a guest's vcpu_num can be easily calculated
from cpu_affinity_bitmap, so don't assign vcpu_num in vm_configuration.c.
Tracked-On: #4616
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Add FADT table support to support guest S5 setting.
According to ACPI 6.3 Spec, OSPM must ignored the DSDT and FACS fields if them're zero.
However, Linux kernel seems not to abide by the protocol, it will check DSDT still.
So add an empty DSDT to meet it.
Tracked-On: #4623
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Remove sdc2 scenario since the VM launch requirement under this scenario
could be satisfied by industry scenario now;
Tracked-On: #4661
Signed-off-by: Victor Sun <victor.sun@intel.com>
