Using physical APIC IDs as vLAPIC IDs for pre-Launched and post-launched VMs
is not sufficient to replicate the host CPU and cache topologies in guest VMs,
we also need to passthrough host CPUID leaf.0BH to guest VMs, otherwise,
guest VMs may see weird CPU topology.
Note that in current code, ACRN has already passthroughed host cache CPUID
leaf 04H to guest VMs
Tracked-On: #6020
Reviewed-by: Wang, Yu1 <yu1.wang@intel.com>
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
In current code, ACRN uses physical APIC IDs as vLAPIC IDs for SOS,
and vCPU ids (contiguous) as vLAPIC IDs for pre-Launched and post-Launched VMs.
Using vCPU ids as vLAPIC IDs for pre-Launched and post-Launched VMs
would result in wrong CPU and cache topologies showing in the guest VMs,
and could adversely affect performance if the guest VM chooses to detect
CPU and cache topologies and optimize its behavior accordingly.
Uses physical APIC IDs as vLAPIC IDs (and related CPU/cache topology enumeration
CPUIDs passthrough) will replicate the host CPU and cache topologies in pre-Launched
and post-Launched VMs.
Tracked-On: #6020
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Signed-off-by: dongshen <dongsheng.x.zhang@intel.com>
Remove the direct calls to exec_vmptrld() or exec_vmclear(), and replace
with the wrapper APIs load_va_vmcs() and clear_va_vmcs().
Tracked-On: #5923
Signed-off-by: Zide Chen <zide.chen@intel.com>
This patch implements the VMREAD and VMWRITE instructions.
When L1 guest is running with an active VMCS12, the “VMCS shadowing”
VM-execution control is always set to 1 in VMCS01. Thus the possible
behavior of VMREAD or VMWRITE from L1 could be:
- It causes a VM exit to L0 if the bit corresponds to the target VMCS
field in the VMREAD bitmap or VMWRITE bitmap is set to 1.
- It accesses the VMCS referenced by VMCS01 link pointer (VMCS02 in
our case) if the above mentioned bit is set to 0.
This patch handles the VMREAD and VMWRITE VM exits in this way:
- on VMWRITE, it writes the desired VMCS value to the respective field
in the cached VMCS12. For VMCS fields that need to be synced to VMCS02,
sets the corresponding dirty flag.
- on VMREAD, it reads the desired VMCS value from the cached VMCS12.
Tracked-On: #5923
Signed-off-by: Alex Merritt <alex.merritt@intel.com>
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
This patch is to emulate VMCLEAR instruction.
L1 hypervisor issues VMCLEAR on a VMCS12 whose state could be any of
these: active and current, active but not current, not yet VMPTRLDed.
To emulate the VMCLEAR instruction, ACRN sets the VMCS12 launch state to
"clear", and if L0 already cached this VMCS12, need to sync it back to
guest memory:
- sync shadow fields from shadow VMCS VMCS to cache VMCS12
- copy cache VMCS12 to L1 guest memory
Tracked-On: #5923
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Enable VMCS shadowing for most of the VMCS fields, so that execution of
the VMREAD or VMWRITE on these shadow VMCS fields from L1 hypervisor
won't cause VM exits, but read from or write to the shadow VMCS.
Tracked-On: #5923
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Alexander Merritt <alex.merritt@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Software layout of VMCS12 data is a contract between L1 guest and L0
hypervisor to run a L2 guest.
ACRN hypervisor caches the VMCS12 which is passed down from L1 hypervisor
by the VMPTRLD instructin. At the time of VMCLEAR, ACRN syncs the cached
VMCS12 back to L1 guest memory.
Tracked-On: #5923
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
This patch emulates the VMPTRLD instruction. L0 hypervisor (ACRN) caches
the VMCS12 that is passed down from the VMPTRLD instruction, and merges it
with VMCS01 to create VMCS02 to run the nested VM.
- Currently ACRN can't cache multiple VMCS12 on one vCPU, so it needs to
flushes active but not current VMCS12s to L1 guest.
- ACRN creates VMCS02 to run nested VM based on VMCS12:
1) copy VMCS12 from guest memory to the per vCPU cache VMCS12
2) initialize VMCS02 revision ID and host-state area
3) load shadow fields from cache VMCS12 to VMCS02
4) enable VMCS shadowing before L1 Vm entry
Tracked-On: #5923
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
This patch implements the VMXOFF instruction. By issuing VMXOFF,
L1 guest Leaves VMX Operation.
- cleanup VCPU nested virtualization context states in VMXOFF handler.
- implement check_vmx_permission() to check permission for VMX operation
for VMXOFF and other VMX instructions.
Tracked-On: #5923
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
According to VMXON Instruction Reference, do the following checks in the
virtual hardware environment: vCPU CPL, guest CR0, CR4, revision ID
in VMXON region, etc.
Currently ACRN doesn't support 32-bit L1 hypervisor, and injects an #UD
exception if L1 hypervisor is not running in 64-bit mode.
Tracked-On: #5923
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
This patch emulates VMXON instruction. Basically checks some
prerequisites to enable VMX operation on L1 guest (next patch), and
prepares some virtual hardware environment in L0.
Tracked-On: #5923
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
The commit 2ab70f43e5
HV: cache: Fix page fault by flushing cache for VM trusty RAM in HV
It is wrong in using stac()/clac()
Tracked-On: #6020
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Now guest would use `Destination Shorthand` to broadcast IPIs if there're more
than one destination. However, it is not supported when the guest is in LAPIC
passthru situation, and all active VCPUs are working in X2APIC mode. As a result,
the guest would not work properly since this kind broadcast IPIs was ignored
by ACRN. What's worse, ACRN Hypervisor would inject GP to the guest in this case.
This patch extend vlapic_x2apic_pt_icr_access to support more destination modes
(both `Physical` and `Logical`) and destination shorthand (`No Shorthand`, `Self`,
`All Including Self` and `All Excluding Self`).
Tracked-On: #5923
Signed-off-by: Zide Chen <zide.chen@intel.com>
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The accrss right of HV RAM can be changed to PAGE_USER (eg. trusty RAM
of post-launched VM). So before using clflush(or clflushopt) to flush
HV RAM cache, must allow explicit supervisor-mode data accesses to
user-mode pages. Otherwise, it may trigger page fault.
Tracked-On: #6020
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Hypervisor does not need to care about hugepage settings in SOS kernel, user
could enable these settings in the scenario config file or GRUB menu.
Tracked-On: #5815
Signed-off-by: Victor Sun <victor.sun@intel.com>
changes:
1. The VM load order type condition is not needed, since the function
is called only when create SOS VM or pre-launched VM;
2. Fixed wrong parameter of fill_seed_arg() which introduced by commit
80262f0602.
3. More comments on why multiboot string could override the pre-
configured VM bootargs and why append multiboot cmdline to SOS VM
bootargs;
Tracked-On: #5815
Signed-off-by: Victor Sun <victor.sun@intel.com>
Use BUILD_VERSION an BUILD_TAG variable also for hypervisor,
acrnprobe and crashlog. This eases build from an archive without
git available.
Tracked-On: #6035
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@opensource.tttech-industrial.com>
Make builds reproducible by honoring SOURCE_DATE_EPOCH and USER
environment variables in the respective Makefiles. Just follow the
recommendations at https://reproducible-builds.org/
Build tools (e.g. Debian packaging, Yocto) use this to ensure reproducibility
of packages.
Tracked-On: #6035
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@opensource.tttech-industrial.com>
Create virtual root port through add_vdev hypercall. add_vdev
identifies the virtual device to add by its vendor id and device id, then
call the corresponding function to create virtual device.
-create_vrp(): Find the right virtual root port to create
by its secondary bus number, then initialize the virtual root port.
And finally initialize PTM related configurations.
-destroy_vrp(): nothing to destroy
Tracked-On: #5915
Signed-off-by: Rong Liu <rong.l.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Acked-by: Jason Chen <jason.cj.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Add virtual root port that supports the most basic pci-e bridge and root port operations.
- init_vroot_port(): init vroot_port's basic registers.
- deinit_vroot_port(): reset vroot_port
- read_vroot_port_cfg(): read from vroot_port's virtual config space.
- write_vroot_port_cfg(): write to vroot_port's virtual config space.
Tracked-On: #5915
Signed-off-by: Rong Liu <rong.l.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Acked-by: Jason Chen <jason.cj.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
If PTM can be enabled on passthru device, a virtual root port
is added to vm to act as ptm root. And the passthru device is
connected to the virtual root port instead of the virtual host bridge.
Tracked-On: #5915
Signed-off-by: Rong Liu <rong.l.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
1. do not allow external modules to touch internal field of a timer.
2. make timer mode internal, period_in_ticks will decide the mode.
API wise:
1. the "mode" parameter was taken out of initialize_timer().
2. a new function update_timer() was added to update the timeout and
period fields.
3. the timer_expired() function was extended with an output parameter
to return the remaining cycles before expiration.
Also, the "fire_tsc" field name of hv_timer was renamed to "timeout".
With the new API, however, this change should not concern user code.
Tracked-On: #5920
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
x86/timer.[ch] was moved to the common directory largely unchanged.
x86 specific code now resides in x86/tsc_deadline_timer.c and its
interface was defined in hw/hw_timer.h. The interface defines two
functions: init_hw_timer() and set_hw_timeout() that provides HW
specific initialization and timer interrupt source.
Other than these two functions, the timer module is largely arch
agnostic.
Tracked-On: #5920
Signed-off-by: Rong Liu <rong2.liu@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Modules that use udelay() should include "delay.h" explicitly.
Tracked-On: #5920
Signed-off-by: Rong Liu <rong2.liu@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Generalize and split basic cpu cycle/tick routines from x86/timer:
- Instead of rdstc(), use cpu_ticks() in generic code.
- Instead of get_tsc_khz(), use cpu_tickrate() in generic code.
- Include "common/ticks.h" instead of "x86/timer.h" in generic code.
- CYCLES_PER_MS is renamed to TICKS_PER_MS.
The x86 specific API rdstc() and get_tsc_khz(), as well as TSC_PER_MS
are still available in arch/x86/tsc.h but only for x86 specific usage.
Tracked-On: #5920
Signed-off-by: Rong Liu <rong2.liu@intel.com>
Signed-off-by: Yi Liang <yi.liang@intel.com>
RTCT has been updated to version 2,
this patch updates hypervisor RTCT parser to support
both version 1 and version 2 of RTCT.
Tracked-On: #6020
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Jason CJ Chen <jason.cj.chen@intel.com>
'psram' and 'PSRAM' are legacy names and replaced
with 'ssram' and 'SSRAM' respectively.
Tracked-On: #6012
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Shuang Zheng <shuang.zheng@intel.com>
Define LIST_OF_VMX_MSRS which includes a list of MSRs that are visible to
L1 guests if nested virtualization is enabled.
- If CONFIG_NVMX_ENABLED is set, these MSRs are included in
emulated_guest_msrs[].
- otherwise, they are included in unsupported_msrs[].
In this way we can take advantage of the existing infrastructure to
emulate these MSRs.
Tracked-On: #5923
Spick igned-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In order to support nested virtualization, need to expose the "Enable VMX
outside SMX operation" bit to L1 hypervisor.
Tracked-On: #5923
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
For simplification purpose, use 'ssram' instead of
'software sram' for local names inside rtcm module.
Tracked-On: #6015
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Move Cache/TLB arch specific parts into cpu.h
After this change, we should not expose arch specific parts out from mmu.h
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Allow guest set CR4_VMXE if CONFIG_NVMX_ENABLED is set:
- move CR4_VMXE from CR4_EMULATED_RESERVE_BITS to CR4_TRAP_AND_EMULATE_BITS
so that CR4_VMXE is removed from cr4_reserved_bits_mask.
- force CR4_VMXE to be removed from cr4_rsv_bits_guest_value so that CR4_VMXE
is able to be set.
Expose VMX feature (CPUID01.01H:ECX[5]) to L1 guests whose GUEST_FLAG_NVMX_ENABLED
is set.
Assuming guest hypervisor (L1) is KVM, and KVM uses EPT for L2 guests.
Constraints on ACRN VM.
- LAPIC passthrough should be enabled.
- use SCHED_NOOP scheduler.
Tracked-On: #5923
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
moving invvpid and invept helper code from mmu.c to mmu.h, so that they
can be accessed by the nested virtualization code.
No logical changes.
Tracked-On: #5923
Signed-off-by: Zide Chen <zide.chen@intel.com>
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
NVMX_ENABLED: ACRN is built to support nested virtualization if set.
GUEST_FLAG_NVMX_ENABLED: indicates that the VMX capability can be present
in this guest to run nested VMs.
Tracked-On: #5923
Signed-off-by: Zide Chen <zide.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
TPAUSE, UMONITOR or UMWAIT instructions execution in guest VM cause
a #UD if "enable user wait and pause" (bit 26) of VMX_PROCBASED_CTLS2
is not set. To fix this issue, set the bit 26 of VMX_PROCBASED_CTLS2.
Besides, these WAITPKG instructions uses MSR_IA32_UMWAIT_CONTROL. So
load corresponding vMSR value during context switch in of a vCPU.
Please note, the TPAUSE or UMWAIT instruction causes a VM exit if the
"RDTSC exiting" and "enable user wait and pause" are both 1. In ACRN
hypervisor, "RDTSC exiting" is always 0. So TPAUSE or UMWAIT doesn't
cause a VM exit.
Performance impact:
MSR_IA32_UMWAIT_CONTROL read costs ~19 cycles;
MSR_IA32_UMWAIT_CONTROL write costs ~63 cycles.
Tracked-On: #6006
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
The current permission-checking and dispatching mechanism of hypercalls is
not unified because:
1. Some hypercalls require the exact vCPU initiating the call, while the
others only need to know the VM.
2. Different hypercalls have different permission requirements: the
trusty-related ones are enabled by a guest flag, while the others
require the initiating VM to be the Service OS.
Without a unified logic it could be hard to scale when more kinds of
hypercalls are added later.
The objectives of this patch are as follows.
1. All hypercalls have the same prototype and are dispatched by a unified
logic.
2. Permissions are checked by a unified logic without consulting the
hypercall ID.
To achieve the first objective, this patch modifies the type of the first
parameter of hcall_* functions (which are the callbacks implementing the
hypercalls) from `struct acrn_vm *` to `struct acrn_vcpu *`. The
doxygen-style documentations are updated accordingly.
To achieve the second objective, this patch adds to `struct hc_dispatch` a
`permission_flags` field which specifies the guest flags that must ALL be
set for a VM to be able to invoke the hypercall. The default value (which
is 0UL) indicates that this hypercall is for SOS only. Currently only the
`permission_flag` of trusty-related hypercalls have the non-zero value
GUEST_FLAG_SECURE_WORLD_ENABLED.
With `permission_flag`, the permission checking logic of hypercalls is
unified as follows.
1. General checks
i. If the VM is neither SOS nor having any guest flag that allows
certain hypercalls, it gets #UD upon executing the `vmcall`
instruction.
ii. If the VM is allowed to execute the `vmcall` instruction, but
attempts to execute it in ring 1, 2 or 3, the VM gets #GP(0).
2. Hypercall-specific checks
i. If the hypercall is for SOS (i.e. `permission_flag` is 0), the
initiating VM must be SOS and the specified target VM cannot be a
pre-launched VM. Otherwise the hypercall returns -EINVAL without
further actions.
ii. If the hypercall requires certain guest flags, the initiating VM
must have all the required flags. Otherwise the hypercall returns
-EINVAL without further actions.
iii. A hypercall with an unknown hypercall ID makes the hypercall
returns -EINVAL without further actions.
The logic above is different from the current implementation in the
following aspects.
1. A pre-launched VM now gets #UD (rather than #GP(0)) when it attempts
to execute `vmcall` in ring 1, 2 or 3.
2. A pre-launched VM now gets #UD (rather than the return value -EPERM)
when it attempts to execute a trusty hypercall in ring 0.
3. The SOS now gets the return value -EINVAL (rather than -EPERM) when it
attempts to invoke a trusty hypercall.
4. A post-launched VM with trusty support now gets the return value
-EINVAL (rather than #UD) when it attempts to invoke a non-trusty
hypercall or an invalid hypercall.
v1 -> v2:
- Update documentation that describe hypercall behavior.
- Fix Doxygen warnings
Tracked-On: #5924
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Fix a couple of typos in text displayed by a helper script
used when building ACRN. No functional change made to the
script itself.
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Instead of "#include <x86/foo.h>", use "#include <asm/foo.h>".
In other words, we are adopting the same practice in Linux kernel.
Tracked-On: #5920
Signed-off-by: Liang Yi <yi.liang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Add "transform" to generate following files with xsltproc in genconf.sh:
- ivshmem_cfg.h
- misc_cfg.h
- pt_intx.c
- vm_configurations.c
- vm_configurations.h
Add code formatter using clang-format. It formats the gernerated code
with customized condfiguration if clang-format package and configuraion
file ".clang-format" exist.
Add sed in genconf.sh "transform" to replace the copyright "YEAR" of generated files.
Tracked-On: #5980
Signed-off-by: Yang,Yu-chu <yu-chu.yang@intel.com>
Reviewed-by: Junjie Mao <junjie.mao@intel.com>
We should only map [low32_max_ram, 4G) MMIO region as UC attribute,
not map [low32_max_ram, low32_max_ram + 4G) region as UC attribute.
Otherwise, the HV will complain [4G, low32_max_ram + 4G) region has
already mapped.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
This patch fixes the 'uart=bdf@XXX' mechanism for the PCI serial
port devices which bar0 is not MMIO.
Tracked-On: #5968
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Signed-off-by: Li Fei <fei1.li@intel.com>
Both Windows guest and Linux guest use the MSR MSR_IA32_CSTAR, while
Linux uses it rarely. Now vcpu context switch doesn't save/restore it.
Windows detects the change of the MSR and rises a exception.
Do the save/resotre MSR_IA32_CSTAR during context switch.
Tracked-On: #5899
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
TLFS spec defines that when a VM is created, the value of
HV_X64_MSR_TIME_REF_COUNT is set to zero. Now tsc_offset is not
supported properly, so guest get a drifted reference time.
This patch implements tsc_offset. tsc_scale and tsc_offset
are calculated when a VM is launched and are saved in
struct acrn_hyperv of struct acrn_vm.
Tracked-On: #5956
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
TLFS spec defines that HV_X64_MSR_VP_INDEX and HV_X64_MSR_TIME_REF_COUNT
are read-only MSRs. Any attempt to write to them results in a #GP fault.
Fix the issue by returning error in handler hyperv_wrmsr() of MSRs
HV_X64_MSR_VP_INDEX/HV_X64_MSR_TIME_REF_COUNT emulation.
Tracked-On: #5956
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
TLFS spec defines different hypercall ABIs for X86 and x64. Currently
x64 hypercall interface is not supported well.
Setup the hypercall interface page according to the vcpu mode.
Tracked-On: #5956
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
These two MACROs shall be wrapped as a single
value respectively, hence brackets should be used.
Tracked-On: #5951
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
In order to support platform (such as Ander Lake) which physical address width
bits is 46, the current code need to reserve 2^16 PD page ((2^46) / (2^30)).
This is a complete waste of memory.
This patch would reserve PD page by three parts:
1. DRAM - may take PD_PAGE_NUM(CONFIG_PLATFORM_RAM_SIZE) PD pages at most;
2. low MMIO - may take PD_PAGE_NUM(MEM_1G << 2U) PD pages at most;
3. high MMIO - may takes (CONFIG_MAX_PCI_DEV_NUM * 6U) PD pages (may plus
PDPT entries if its size is larger than 1GB ) at most for:
(a) MMIO BAR size must be a power of 2 from 16 bytes;
(b) MMIO BAR base address must be power of two in size and are aligned with
its size.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
The platform which physical-address width over 39 bits must support
1GB large page (Both MMU and VMX sides ). This could save lots of
page table pages for EPT MMIO mapping.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
No one uses get_mem_range_info to get the top/bottom/size of the physical memory.
We could get these informations by e820 table easily.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: eddie Dong <eddie.dong@intel.com>
We used get_mem_range_info to get the top memory address and then use this address
as the high 64 bits max memory address of SOS. This assumes the platform must have
high memory space.
This patch removes the assumption. It will set high 64 bits max memory address of
SOS to 4G by default (Which means there's no 64 bits high memory), then update
the high 64 bits max memory address if the SOS really has high memory space.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: eddie Dong <eddie.dong@intel.com>
SOS's memory size could be calculated by its vE820 Tables easily.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: eddie Dong <eddie.dong@intel.com>
We used get_mem_range_info to get the top memory address and then use this address
as the high 64 bits max memory address. This assumes the platform must have high
memory space.
This patch calculates the high 64 bits max memory address according the e820 tables
and removes the assumption "The platform must have high memory space" by map the
low RAM region and high RAM region separately.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: eddie Dong <eddie.dong@intel.com>
Now BSP may launch VMs before APs have not done its initilization,
for example, sched_control for per-cpu. However, when we initilize
the vcpu thread data, it will access the object (scheduler) of the
sched_control of APs. As a result, it will trigger the PF.
This patch would waits each physical has done its initilization before
to continue to execute.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Using the MFENCE to make sure trampoline code
has been updated (clflush) into memory beforing start APs.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Use MFENCE to strengthen the fast string operations execute order to ensure
all trampoline code was updated before flush it into the memory.
Tracked-On: #5929
Signed-off-by: Li Fei1 <fei1.li@intel.com>
For platform with HLAT (Hypervisor-managed Linear Address Translation)
capability, the hypervisor shall hide this feature to its guest.
This patch adds MSR_IA32_VMX_PROCBASED_CTLS3 MSR to unsupported MSR
list.
The presence of this MSR is determined by 1-setting of bit 49 of MSR
MSR_IA32_VMX_PROCBASED_CTLS. which is already in unsupported MSR list. [2]
Related documentations:
[1] Intel Architecture Instruction Set Extensions, version Feb 16, 2021,
Ch 6.12
[2] Intel KeyLocker Specification, Sept 2020, Ch 7.2
Tracked-On: #5895
Signed-off-by: Yifan Liu <yifan1.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch adds the following dependencies among recipes:
- Building of any C file depends on $(HV_CONFIG_TIMESTAMP) which indicates
the presence of generated configuration files.
- Source files listed in $(VM_CFG_C_SRCS), which are the generated
configuration files, depends on $(HV_CONFIG_TIMESTAMP)
With the dependencies above, the build system can now safely be executed in
parallel, e.g. `make -j4`.
Tracked-On: #5874
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
sanitize_pte is used to set page table entry to map to an sanitized page to
mitigate l1tf. It should belongs to pgtable module. So move it to pagetable.c
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
lookup_address is used to lookup a pagetable entry by an address. So rename it
to pgtable_lookup_entry to indicate this clearly.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
alloc_page/free_page should been called in pagetable module. In order to do this,
we add pgtable_create_root and pgtable_create_trusty_root to create PML4 page table
page for normal world and secure world.
After this done, no one uses alloc_ept_page. So remove it.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Add pgtable_create_trusty_root to allocate a page for trusty PML4 page table page.
This function also copy PDPT entries from Normal world to Secure world.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Add pgtable_create_root to allocate a page for PMl4 page table page.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Rename mmu_add to pgtable_add_map;
Rename mmu_modify_or_del to pgtable_modify_or_del_map.
And move these functions declaration into pgtable.h
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
In VT-d scenario, if MSI interrupt has been enabled,
vCPU writes the content in MSI registers,
and all bits of the content are read-only.
In this case, hypervisor code will call
enable_disable_msi(vdev, false), which will disable MSI.
And there's no chance to call remap_vmsi.
This is wrong behavior, which will result in the disable of MSI.
Tracked-On: #5847
Reviewed-by: Li Fei1 <fei1.li@intel.com>
Signed-off-by: liujunming <junming.liu@intel.com>
Requires explicit arch path name in the include directive.
The config scripts was also updated to reflect this change.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Each .c file includes the arch specific irq header file (with full
path) by itself if required.
Tracked-On: #5825
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
A new x86/guest/virq.h head file now contains all guest
related interrupt handling API.
Tracked-On: #5825
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Each of them now resides in a separate .c file.
Tracked-On: #5825
Signed-off-by: Yang, Yu-chu <yu-chu.yang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Move exception stack layout struct and exception/NMI handling
declarations from x86/irq.h into x86/cpu.h.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The common irq file is responsible for managing the central
irq_desc data structure and provides the following APIs for
host interrupt handling.
- init_interrupt()
- reserve_irq_num()
- request_irq()
- free_irq()
- set_irq_trigger_mode()
- do_irq()
API prototypes, constant and data structures belonging to common
interrupt handling are all moved into include/common/irq.h.
Conversely, the following arch specific APIs are added which are
called from the common code at various points:
- init_irq_descs_arch()
- setup_irqs_arch()
- init_interrupt_arch()
- free_irq_arch()
- request_irq_arch()
- pre_irq_arch()
- post_irq_arch()
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
This is done be adding irq_rsvd_bitmap as an auxiliary bitmap
besides irq_alloc_bitmap.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The common IRQ handling routine calls arch specific functions
pre_irq_arch() and post_irq_arch() before and after calling the
registered action function respectively.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The common part initializes the global irq_desc data structure while the
arch specific part initialize the HW and its own irq data.
This is one of the preparation steps for spliting IRQ handling into common
and architecture specific parts.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Arch specific IRQ data is now an opaque pointer in irq_desc.
This is a preparation step for spliting IRQ handling into common
and architecture specific parts.
Tracked-On: #5825
Signed-off-by: Peter Fang <peter.fang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The 'uart=' parameter for the hypervisor takes multiple forms. One
is to specify the BDF (Bus, Device, Function) value of the serial
port PCI device. The description in the documentation used the
previous format (e.g. '0:18.1') but a 16-bit WORD in HEX needs
to be passed nowadays. E.g.: '0:18.1' is specified by 'uart=0xc1'
Tracked-On: #5842
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Signed-off-by: Benjamin Fitch <benjamin.fitch@intel.com>
This patch moves pgtable definition to pgtable.h and include the proper
header file for page module.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Move the EPT page table related APIs to ept.c. page module only provides APIs to
allocate/free page for page table page. pagetabl module only provides APIs to
add/modify/delete/lookup page table entry. The page pool and the page table
related APIs for EPT should defined in EPT module.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Move the MMU page table related APIs to mmu.c. page module only provides APIs to
allocate/free page for page table page. pagetabl module only provides APIs to
add/modify/delete/lookup page table entry. The page pool and the page table
related APIs for MMU should defined in MMU module.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
We would move the MMU page table related APIs to mmu.c and move the EPT related
APIs to EPT.c. The page table module only provides APIs to add/modify/delete/lookup
page table entry.
This patch separates common APIs and adds separate APIs of page table module
for MMU/EPT.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
post_uos_sworld_memory are used for post-launched VM which support trusty.
It's more VM related. So move it definition into vm.c
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Per-core software SRAM L2 cache may be flushed by 'mwait'
extension instruction, which guest VM may execute to enter
core deep sleep. Such kind of flushing is not expected when
software SRAM is enabled for RTVM.
Hypervisor disables MONITOR-WAIT support on both hypervisor
and VMs sides to protect above software SRAM from being flushed.
This patch disable ACRN guest MONITOR-WAIT support if software
SRAM is configured.
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Per-core software SRAM L2 cache may be flushed by 'mwait'
extension instruction, which guest VM may execute to enter
core deep sleep. Such kind of flushing is not expected when
software SRAM is enabled for RTVM.
Hypervisor disables MONITOR-WAIT support on both hypervisor
and VMs sides to protect above software SRAM from being flushed.
This patch disable hypervisor(host) MONITOR-WAIT support and refine
software sram initializaion flow.
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Below boolean function are defined in this patch:
- is_software_sram_enabled() to check if SW SRAM
feature is enabled or not.
- set global variable 'is_sw_sram_initialized'
to file static.
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The fields and APIs in old 'struct memory_ops' are used to add/modify/delete
page table (page or entry). So rename 'struct memory_ops' to 'struct pgtable'.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Use default_access_right field to replace get_default_access_right API.
Tracked-On: #5830
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
RTVM is enforced to use 4KB pages to mitigate CVE-2018-12207 and performance jitter,
which may be introduced by splitting large page into 4KB pages on demand. It works
fine in previous hardware platform where the size of address space for the RTVM is
relatively small. However, this is a problem when the platforms support 64 bits
high MMIO space, which could be super large and therefore consumes large # of
EPT page table pages.
This patch optimize it by using large page for purely data pages, such as MMIO spaces,
even for the RTVM.
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Tracked-On: #5788
To mitigate the page size change MCE vulnerability (CVE-2018-12207), ACRN would
clear the execution permission in the EPT paging-structure entries for large pages
and then intercept an EPT execution-permission violation caused by an attempt to
execution an instruction in the guest.
However, the current code would clear the execution permission in the EPT paging-
structure entries for small pages too when we clearing the the execution permission
for large pages. This would trigger extra EPT violation VM exits.
This patch fix this issue.
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Tracked-On: #5788
The top-level Makefile should not define any default value as the
hypervisor may have its own configurations set by previous builds.
This patch also changes the hypervisor default RELEASE to `n`.
Tracked-On: #5772
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
This patch resolves the following bugs that break the targets `diffconfig`
and `applydiffconfig`:
- Comments after variable definitions cause the varaible to contain
unintended trailing whitespaces.
- HV_CONFIG_XML is no longer defined; it is now HV_SCENARIO_XML.
- '*.asl' files are also generated and should be involved when comparing
the generated configuration files.
- Strings between diacritic marks (`) are intepreted as shell commands
even they are part of informative messages.
- HV_DIFFCONFIG_LIST should not contain duplicated lines.
Tracked-On: #5772
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
For clarity, we now prefer y|n over 0|1 as the values of boolean options on
make command lines. This patch applies this preference to the Makefile of
the device model and tools, while RELEASE=0|1 is still supported for
backward compatibility.
Tracked-On: #5772
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
SOS_RAM_SIZE/UOS_RAM_SIZE Kconfig are only used to calculate how many pages we
should reserve for the VM EPT mapping.
Now we reserve pages for each VM EPT pagetable mapping by the PLATFORM_RAM_SIZE
not the VM RAM SIZE. This could simplify the reserve logic for us: not need to
take care variable corner cases. We could make assume we reserve enough pages
base on the VM could not use the resources beyond the platform hardware resources.
So remove these two unused VM ram size kconfig.
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Tracked-On: #5788
Add free_page to free page when unmap pagetable.
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Tracked-On: #5788
For FuSa's case, we remove all dynamic memory allocation use in ACRN HV. Instead,
we use static memory allocation or embedded data structure. For pagetable page,
we prefer to use an index (hva for MMU, gpa for EPT) to get a page from a special
page pool. The special page pool should be big enougn for each possible index.
This is not a big problem when we don't support 64 bits MMIO. Without 64 bits MMIO
support, we could use the index to search addrss not larger than DRAM_SIZE + 4G.
However, if ACRN plan to support 64 bits MMIO in SOS, we could not use the static
memory alocation any more. This is because there's a very huge hole between the
top DRAM address and the bottom 64 bits MMIO address. We could not reserve such
many pages for pagetable mapping as the CPU physical address bits may very large.
This patch will use dynamic page allocation for pagetable mapping. We also need
reserve a big enough page pool at first. For HV MMU, we don't use 4K granularity
page table mapping, we need reserve PML4, PDPT and PD pages according the maximum
physical address space (PPT va and pa are identical mapping); For each VM EPT,
we reserve PML4, PDPT and PD pages according to the maximum physical address space
too, (the EPT address sapce can't beyond the physical address space), and we reserve
PT pages by real use cases of DRAM, low MMIO and high MMIO.
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Tracked-On: #5788
memory_ops structure will be changed to store page table related fields.
However, secure world memory base address is not one of them, it's VM
related. So save sworld_memory_base_hva in vm_arch structure directly.
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Tracked-On: #5788
Current memory allocation algorithm is to find the available address from
the highest possible address below max_address. If the function returns 0,
means all memory is used up and we have to put the resource at address 0,
this is dangerous for a running hypervisor.
Also returns 0 would make code logic very complicated, since memcpy_s()
doesn't support address 0 copy.
Tracked-On: #5626
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
In previous code, the rsdp initialization is done in get_rsdp() api implicitly.
The function is called multiple times in following acpi table parsing functions
and the condition (rsdp == NULL) need to be added in each parsing function.
This is not needed since the panic would occur if rsdp is NULL when do acpi
initialization.
Tracked-On: #5626
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
In this way, all multiboot standard data structure could be found in
multiboot_std.h. The multiboot_priv.h stores all private definitions
and multiboot.h is the only public API header file.
Tracked-On: #5661
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Accessing to software SRAM region is not allowed when
software SRAM is pass-thru to prelaunch RTVM.
This patch removes software SRAM region from service VM
EPT if it is enabled for prelaunch RTVM.
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Fixing an incorrect struct definition for ir_bits in ioapic_rte. Since bits after
the delivery status in the lower 32 bits are not touched by code,
this has never showed up as an issue. And the higher 32 bits in the RTE
are aligned by the compiler.
Tracked-On: #5773
Signed-off-by: Sainath Grandhi <sainath.grandhi@intel.com>
Currently the VM bootargs load address is hard-coded at 8KB right before
kernel load address, this should work for Linux kernel only since Linux
kernel is guaranteed to be loadered high than GPA 8K so its load address
would never be overflowed, other OS like Zephyr has no such assumption.
Tracked-On: #5689
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
ivshmem spec says that the size of BAR0 is 256 bytes. Windows
ivshmem driver will check the size of BAR0. It will refuse to
load the ivshmem driver if BAR0 size is not 256.
For post-launched VM hv land ivshmem BARs are allocated by
device model. For pre-launched VM hv land ivshmem BARs are
allocated by acrn-config tool. Both device model and acrn-config
tool should make sure that the BAR base addr are aligned to 4K
at least.
Tracked-On: #5717
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch denies Service VM the access permission to device resources
owned by hypervisor.
HV may own these devices: (1) debug uart pci device for debug version
(2) type 1 pci device if have pre-launched VMs.
Current implementation exposes the mmio/pio resource of HV owned devices
to SOS, should remove them from SOS.
Tracked-On: #5615
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
This patch denies Service VM the access permission to device
resources owned by pre-launched VMs.
Rationale:
* Pre-launched VMs in ACRN are independent of service VM,
and should be immune to attacks from service VM. However,
current implementation exposes the bar resource of passthru
devices to service VM for some reason. This makes it possible
for service VM to crash or attack pre-launched VMs.
* It is same for hypervisor owned devices.
NOTE:
* The MMIO spaces pre-allocated to VFs are still presented to
Service VM. The SR-IOV capable devices assigned to pre-launched
VMs doesn't have the SR-IOV capability. So the MMIO address spaces
pre-allocated by BIOS for VFs are not decoded by hardware and
couldn't be enabled by guest. SOS may live with seeing the address
space or not. We will revisit later.
Tracked-On: #5615
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The logical processor scoped IWKey can be copied to or from a
platform-scope storage copy called IWKeyBackup. Copying IWKey to
IWKeyBackup is called ‘backing up IWKey’ and copying from IWKeyBackup to
IWKey is called ‘restoring IWKey’.
IWKeyBackup and the path between it and IWKey are protected against
software and simple hardware attacks. This means that IWKeyBackup can be
used to distribute an IWKey within the logical processors in a platform
in a protected manner.
Linux keylocker implementation uses this feature, so they are
introduced by this patch.
Tracked-On: #5695
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Different vCPU may have different IWKeys. Hypervisor need do the iwkey
context switch.
This patch introduce a load_iwkey() function to do that. Switches the
host iwkey when the switch_in vCPU satisfies:
1) keylocker feature enabled
2) Different from the current loaded one.
Two opportunities to do the load_iwkey():
1) Guest enables CR4.KL bit.
2) vCPU thread context switch.
load_iwkey() costs ~600 cycles when do the load IWKey action.
Tracked-On: #5695
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
KeyLocker is a new security feature available in new Intel CPUs that
protects data-encryption keys for the Advanced Encryption Standard (AES)
algorithm. These keys are more valuable than what they guard. If stolen
once, the key can be repeatedly used even on another system and even
after vulnerability closed.
It also introduces a CPU-internal wrapping key (IWKey), which is a key-
encryption key to wrap AES keys into handles. While the IWKey is
inaccessible to software, randomizing the value during the boot-time
helps its value unpredictable.
Keylocker usage:
- New “ENCODEKEY” instructions take original key input and returns HANDLE
crypted by an internal wrap key (IWKey, init by “LOADIWKEY” instruction)
- Software can then delete the original key from memory
- Early in boot/software, less likely to have vulnerability that allows
stealing original key
- Later encrypt/decrypt can use the HANDLE through new AES KeyLocker
instructions
- Note:
* Software can use original key without knowing it (use HANDLE)
* HANDLE cannot be used on other systems or after warm/cold reset
* IWKey cannot be read from CPU after it's loaded (this is the
nature of this feature) and only 1 copy of IWKey inside CPU.
The virtualization implementation of Key Locker on ACRN is:
- Each vCPU has a 'struct iwkey' to store its IWKey in struct
acrn_vcpu_arch.
- At initilization, every vCPU is created with a random IWKey.
- Hypervisor traps the execution of LOADIWKEY (by 'LOADIWKEY exiting'
VM-exectuion control) of vCPU to capture and save the IWKey if guest
set a new IWKey. Don't support randomization (emulate CPUID to
disable) of the LOADIWKEY as hypervisor cannot capture and save the
random IWKey. From keylocker spec:
"Note that a VMM may wish to enumerate no support for HW random IWKeys
to the guest (i.e. enumerate CPUID.19H:ECX[1] as 0) as such IWKeys
cannot be easily context switched. A guest ENCODEKEY will return the
type of IWKey used (IWKey.KeySource) and thus will notice if a VMM
virtualized a HW random IWKey with a SW specified IWKey."
- In context_switch_in() of each vCPU, hypervisor loads that vCPU's
IWKey into pCPU by LOADIWKEY instruction.
- There is an assumption that ACRN hypervisor will never use the
KeyLocker feature itself.
This patch implements the vCPU's IWKey management and the next patch
implements host context save/restore IWKey logic.
Tracked-On: #5695
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In order for a VMM to capture the IWKey values of guests, processors
that support Key Locker also support a new "LOADIWKEY exiting"
VM-execution control in bit 0 of the tertiary processor-based
VM-execution controls.
This patch enables the tertiary VM-execution controls.
Tracked-On: #5695
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
KeyLocker is a new security feature available in new Intel CPUs that
protects data-encryption keys for the Advanced Encryption Standard (AES)
algorithm.
This patch emulates Keylocker CPUID leaf 19H to support Keylocker
feature for guest VM.
To make the hypervisor being able to manage the IWKey correctly, this
patch doesn't expose hardware random IWKey capability
(CPUID.0x19.ECX[1]) to guest VM.
Tracked-On: #5695
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@Intel.com>
Bit19 (CR4_KL) of CR4 is CPU KeyLocker feature enable bit. Hypervisor
traps the bit's writing to track the keylocker feature on/off of guest.
While the bit is set by guest,
- set cr4_kl_enabled to indicate the vcpu's keylocker feature enabled status
- load vcpu's IWKey in host (will add in later patch)
While the bit is clear by guest,
- clear cr4_kl_enabled
This patch trap and passthru the CR4_KL bit to guest for operation.
Tracked-On: #5695
Signed-off-by: Shuo A Liu <shuo.a.liu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Current implementation, SOS may allocate the memory region belonging to
hypervisor/pre-launched VM to a post-launched VM. Because it only verifies
the start address rather than the entire memory region.
This patch verifies the validity of the entire memory region before
allocating to a post-launched VM so that the specified memory can only
be allocated to a post-launched VM if the entire memory region is mapped
in SOS’s EPT.
Tracked-On: #5555
Signed-off-by: Li Fei1 <fei1.li@intel.com>
Reviewed-by: Yonghua Huang <yonghua.huang@intel.com>
Currently, we hardcode the GPA base of Software SRAM
to an address that is derived from TGL platform,
as this GPA is identical with HPA for Pre-launch VM,
This hardcoded address may not work on other platforms
if the HPA bases of Software SRAM are different.
Now, Offline tool configures above GPA based on the
detection of Software SRAM on specific platform.
This patch removes the hardcoding GPA of Software SRAM,
and also renames MACRO 'SOFTWARE_SRAM_BASE_GPA' to
'PRE_RTVM_SW_SRAM_BASE_GPA' to avoid confusing, as it
is for Prelaunch VM only.
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
- RTCM is initialized in hypervisor only
if RTCM binaries are detected.
- Remove address space of RTCM binary from
Software SRAM region.
- Refine parse_rtct() function, validity of
ACPI RTCT table shall be checked by caller.
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Physical address to SW SRAM region maybe different
on different platforms, this hardcoded address may
result in address mismatch for SW SRAM operations.
This patch removes above hardcoded address and uses
the physical address parsed from native RTCT.
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Fei Li <fei1.li@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
'ptcm' and 'ptct' are legacy name according
to the latest TCC spec, hence rename below files
to avoid confusing:
ptcm.c -> rtcm.c
ptcm.h -> rtcm.h
ptct.h -> rtct.h
Tracked-On: #5649
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
This patch fixes the following issues that break the build system:
1. The tag of the root nodes of board/scenario XML files are still acrn-config,
not config_tools. This patch reverts the XPATH that refers to these nodes.
2. HV_PREDEFINED_BOARD_DIR now also relies on BOARD which may not be
available at the time the variable is defined. As both board and
scenario XML files are placed under the same directory, this patch
refines the path calculation logic to get rid of mixing variables of
the different flavors.
Tracked-On: #5644
Fixes: 97c9b24030 ("acrn-config: Reorg config tool folder")
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Simplify multiboot API by removing the global variable efiloader_sig.
Replaced by constant at the use site.
Tracked-On: #5661
Signed-off-by: Yi Liang <yi.liang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Remove include/boot.h since it contains only assembly variables that
should only be accessed in arch/x86/init.c.
Tracked-On: #5661
Signed-off-by: Yi Liang <yi.liang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Split off definition of "struct efi_info" into a separate header
file lib/efi.h.
Tracked-On: #5661
Signed-off-by: Jason Chen CJ <jason.cj.chen@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
This is done by adding the MAX_MMAP_ENTRIES macro in multiboot.h.
This macro has to be sync-ed with E820_MAX_ENTRIES manually though.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
The init_multiboot_info() and sanitize_multiboot_ifno() APIs now
require parameters instead of implicitly relying on global boot
variables.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Calling sanitize_multiboot() from init.c instead of cpu.c.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
This way, we void exposing acrn_mbi as a global variable.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
This function is a derivative of get_multiboot_info().
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Move "struct multboot_info" from multiboot.h into multboot.c.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Move multiboot specific declarations from boot.h to multiboot.h.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Create multiboot_pri.h and move the relevant declarations into this
file.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Create a multiboot module under the boot directory and move multiboot
files as part of this.
Tracked-On: #5661
Signed-off-by: Vijay Dhanraj <vijay.dhanraj@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Remove vm_configs folder and move all the XML files and generic code example into config_tools/data
Tracked-On: #5644
Signed-off-by: Xie, nanlin <nanlin.xie@intel.com>
In order to enable changing the generated C configuration files manually,
this patch introduces the target `diffconfig` to the build system.
After generating the configuration files, a developer can manually modify
these sources (which are placed under build/configs) and invoke `make
diffconfig` to generate a patch that shows the made differences. Such
patches can be registered to a build by invoking the `applydiffconfig`
target. The build system will always apply them whenever the configuration
files are regenerated.
A typical workflow to create a patch is as follows.
# The pre_build target relies on generated configuration files
hypervisor$ make BOARD=xxx SCENARIO=yyy pre_build
(manually edit files under build/configs/boards and
build/configs/scenarios)
hypervisor$ make diffconfig # Patch generated to build/config.patch
hypervisor$ cp build/config.patch /path/to/patch
The following steps apply apply the patch to another build.
hypervisor$ make BOARD=xxx SCENARIO=yyy defconfig
hypervisor$ make applydiffconfig PATCH=/path/to/patch-file-or-directory
hypervisor$ make
After any patch is registered for a build, the configuration files will be
automatically regenerated the next time `make` is invoked.
To show a list of registered patches for generated configuration files,
invoke `make applydiffconfig` without specifying `PATCH`.
v2:
* Add target `applydiffconfig` which accepts a PATCH variable to register
an arbitrary patch file or a directory containing patch file(s) for a
build. `.config_patches` is no longer used.
Tracked-On: #5644
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
This patch makes the build system of the hypervisor to cache the board and
scenario XML files in the build directory and generate C configuration
files from them at build time. The C configuration files that are cached in
the git repo is no longer used or updated. Paths to these generated files
in the prebuild Makefile is updated accordingly.
The following targets are introduced or modified.
* defconfig: Copy default configuration XMLs to the build directory and
generate C configuration files.
* oldconfig: No action.
* menuconfig: Print a message to redirect users to use the config app
and exit.
* showconfig: Print the BOARD, SCENARIO and RELEASE configured for the
current build.
* update_config: No action.
* (default): Build the hypervisor with defined configurations.
The following variables can be set on the command line to specify the
default configuration to be used.
* BOARD: Either a name of the target board or a path to a customized
board XML. When a board name is specified, the board XML file
is expected to be available under
misc/acrn-config/xmls/board-xmls.
* SCENARIO: Either a name of the scenario of a path to a customized
scenario XML. When a scenario name is specified, the
scenario XML file is expected to be available under
misc/acrn-config/xmls/config-xmls/$(BOARD).
* BOARD_FILE: Path to the board XML file to be used. This is now
obsoleted as BOARD provides the same functionality.
* SCENARIO_FILE: Path to the scenario XML file to be used. This is now
obsoleted as BOARD provides the same functionality.
BOARD/SCENARIO or BOARD_FILE/SCENARIO_FILE shall be used in pair, and
BOARD_FILE/SCENARIO_FILE shall point to valid files when specified. Any
violation to those constraints will stop the build with error
messages. When BOARD/SCENARIO and BOARD_FILE/SCENARIO_FILE are both defined
on the command line, the former takes precedence as the latter are to be
obsoleted.
Additionally, users can define the RELEASE variable to specify a debug or
release build. In case a previous build exists but is configured for a
different build type, the build system will automatically update the
scenario XML and rebuild the sources.
This patch also includes the following tweaks:
1. Do not use `realpath` to process search paths for generated
headers. `realpath` only accepts paths of existing files, while the
directories for generated headers may not be created at the time the
search paths are calculated.
2. Always expect `pci_dev.c` to be in place.
3. HV_CONFIG_* series now encodes absolute paths.
v3:
* Do not validate BOARD_FILE/SCENARIO_FILE if BOARD/SCENARIO are given.
v2:
* `defconfig` now also generates the C configuration files.
* BOARD/SCENARIO now accept either board/scenario names or XML file paths.
* Adapt to the new allocation.xml & unified.xml.
* Cleanup names of internal variables in config.mk for brevity.
Tracked-On: #5644
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
In order to remove Kconfig from the build process, acrn-config shall
transform XML configuration files to config.h and config.mk by itself. This
patch adds XSLT scripts that do the trick.
Unfortunately, the scenario XML file along is not sufficient to generate
config.h and config.mk, though. In addition to resource
allocation (i.e. allocating physical RAM for the hypervisor), the
transformation also need to do the following:
1. Translate UART info in board XML into several configuration entries
depending on the UART selected in the scenario XML.
2. Use the MAX_MSIX_TABLE_NUM value in the board XML if the scenario
XML does not specify it.
In order to use XSLT to transform both XMLs in one shot, a template is
provided to create another XML that includes (using XInclude) both board
and scenario XMLs as sub-nodes. It will be instantiated once the
transformations are integrated in the following patch.
v2:
* Add `allocation.xml` to `unified.xml` to include the results from static
allocation.
* Use HV_RAM_START and HV_RAM_SIZE in allocation results if they are not
explicitly specified in the scenario XML.
Tracked-On: #5644
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
In order for a unified interface for generating configuration sources from
board and scenario XMLs, this patch introduces a script named genconf.sh
which takes XML files as inputs and generate sources under the specified
directory. Once used in Makefiles, this script helps to minimize the
impacts on the Makefiles when we refine the configuration source generation
process in the future.
This patch also adds a non-zero return value to board_cfg_gen.py and
scenario_cfg_gen.py so that we do not need to inspect the logs to determine
if the generation succeeds.
Tracked-On: #5644
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
The commit 'Fix: HV: VM OS failed to assign new address to pci-vuart
BARs' need more reshuffle.
Tracked-On: #5491
Signed-off-by: Tao Yuhong <yuhong.tao@intel.com>
Signed-off-by: Eddie Dong <eddie.dong@intel.com>
When "signal_event" is called, "wait_event" will actually not block.
So it is ok to remove this line.
Tracked-On: #5605
Signed-off-by: Jie Deng <jie.deng@intel.com>
Now, we use hash table to maintain intx irq mapping by using
the key generated from sid. So once the entry is added,we can
not update source ide any more. Otherwise, we can't locate the
entry with the key generated from new source ide.
For source id change, remove_remapping/add_remapping is used
instead of update source id directly if entry was added already.
Tracked-On: #5640
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch move the split-lock logic into dedicated file
to reduce LOC. This may make the logic more clear.
Tracked-On: #5605
Signed-off-by: Jie Deng <jie.deng@intel.com>
This patch adds a cache register for VMX_PROC_VM_EXEC_CONTROLS
to avoid the frequent VMCS access.
Tracked-On: #5605
Signed-off-by: Jie Deng <jie.deng@intel.com>
